2AM8R-D810ADriveri

2.9 11 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Netradyne Inc. Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. Product Name: Driveri FCC ID: 2AM8R-D810A Model(s): D-810 2.911(d)(5)(i) Equipment Type We, [Netradyne Inc.] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: David Julian Date: 17-01-2026 Title and Company name: CTO Netradyne Inc NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Netradyne Inc. Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. Product Name: DriverI FCC ID: 2AM8R- D810A Model(s): D-810 2.911(d)(5)(ii) Applicant filing We, [Netradyne Inc.] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: David Julian Date: 17-01-2026 Title and Company name: CTO Netradyne Inc NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

833-GRN-ZONE | 9171 Towne Centre Drive, #110. San Diego, CA 92122netradyne.com Section 2.911(d)(7) USA Agent for Service of Process Company name: Netradyne Inc Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. Product Name: Driveri FCC ID: 2AM8R-D810 Model(s): D-810, D-810A and D-811 2.911(d)(7) USA Designated Agent for Service of Process We, [Insert applicant name] (“the applicant”) designate [Agent located in the United States] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Netradyne Inc. USA Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. FRN Number: 0026737700 Contact Name: David Julian Telephone No: +1 8587528914 Email: [email protected] Applicant Company name: Netradyne Inc. Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. FRN Number: 0026737700 FCC Grantee Code: 2AM8R Contact Name: David Julian Telephone No: +1 8587528914 Email: [email protected] Signature: Title: CTO Signature: Title: CTO Date: 05-15-2025 Date: 05-15-2025 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats- to-the-communications-supply-chain-through-the

Agent Authorization Company: Netradyne, Inc. Address: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122. Product Name: Driveri Model Number(s): D-810, Derivative Model: D-810A and D-811 Product Description: Driveri (D810) is an AI-powered, vision-based IoT system designed for fleet vehicles. Installed discreetly behind the rear-view mirror, it is powered via a direct connection to the vehicle's battery and can interface with the OBD II or J1939 port to access engine data. The device operates passively, requiring no interaction from the driver. While the vehicle is in motion, Driveri captures 360° video coverage of both the cabin and the vehicle’s exterior using six cameras—two digital for in-cabin monitoring and four analog for external views. The forward-facing camera is the primary recorder, while the remaining exterior cameras can be configured based on customer needs. Onboard patented machine learning algorithms analyse the recorded footage and sensor data to detect driving and driver behaviour events.Upon detecting an event, the device uploads alerts and processed data to a cloud dashboard, allowing fleet managers to monitor incidents in real time. Two driver-facing LEDs indicate the operational status of the device. Additional daughter boards— including an Audio board, Lumia board, and Camera board—enhance the system’s functionality. We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Jan 17, 2026 Name: David Julian Title: CTO Company: Netradyne, Inc.

Declaration letter We, Netradyne Inc, hereby declare that our products are intended for Business-to-Business (B2B) use only and are not sold directly to consumers for personal installation or modification. Our devices are installed exclusively by professional installers who are trained and authorized to perform installation, maintenance, repair, and removal of our equipment. End users or consumers are not permitted to remove, alter, or tamper with any components of our devices, including antennas, for any reason. Should you require any further information or clarification, please do not hesitate to contact us. Signature: Date: 09-06-2025 Name: David Julian Title: CTO Company: Netradyne Inc

833-GRN-ZONE | 9171 Towne Centre Drive, #110. San Diego, CA 92122netradyne.com Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-15-2025 Subject; Request for Confidentiality FCC ID: 2AM8R-D810 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in the operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In addition to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: David Julian Title: CTO

Label-1 Label-2 Label-3

Label Label on EUT

RF EXPOSURE EVALUATION 1. PRODUCTINFORMATION Product Description Driveri Model Name D-810 FCC ID 2AM8R-D810A 2. EVALUATION METHODANDLIMIT Human exposure to RF emissions from mobile devices(47CFR§2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. The device under test (D-810) is neither a mobile device nor a RF exposure product and it is not closed to 20cm distance from persons LIMITS FOR GENERAL POPULATIONIUNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm 2 ) Averaging Time IEl 2 IHl 2 or , S(Minutes) 0.3--1.34 614 1.63 (100)* 30 1.34--30 824/f 2.19/f (180/f 2 )* 30 30--300 27.5 0.073 0.2 30 300--1500 -- -- f/1500 30 1500--100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz*Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. (operated in BT/ WIFI) See47CFR§§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4rrR 2 Where: S=power density P=power input toantenna G=power gain of the antenna in the direction of interest relative to anisotropic radiator R=distance to the center of radiation of the antenna 3. CALCULATION A minimum test separation distance 20cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of §2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. The device under test (Driveri) is neither a mobile device nor a RF exposure product and it is not closed to 20cm distance from persons Antenna Gain (2.4 GHz Wi-Fi, BT and BLE) = 3dBi (Numeric=1.995), rr = 3.14 Note 1: Only the worst case recorded. Note 2: LTE and GPS are mounted externally. Frequency (MHz) Output Power (dBm) Output Power (mW) Power Density (mW/cm 2) Power Density Limit (mW/cm 2) 2437(Wi-Fi) 22.48 177.0108 0.0702 1 2480 (BLE) 7.33 5.4075 0.0021 1 2480(BT) 1.78 1.5066 0.0005 1

SPE-11-8-026-J Freedom Part No: FXP831.07.0100C Description: FXP.831 Freedom 2.4/4.9-6GHz Ground Coupled Antenna Features: Flexible Ultra Low Profile Adheres directly to inside of product plastic or glass housing Dipole Antenna Form factor and cable routing convenient for integration High Efficiency Cable: 100mm of Ø1.37mm Connector: IPEX MHF Connector (U.FL compatible) RoHS & Reach Compliant 2 SPE-11-8-026-J www.taoglas.com Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Taoglas reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 1. Introduction 3 2. Specifications 4 3. Electrical Characteristic 5 4. Radiation Patterns 9 5. Mechanical Drawing 17 6. Precautions for usage 18 7. Packaging 19 Changelog 20 3 SPE-11-8-026-J www.taoglas.com The FXP831 is a high efficiency, small, dual-band, dipole antenna for 2.4/4.9-6GHz band including DSRC, V2V, WiFi, Bluetooth, Zigbee and other applications in these bands. The FXP.831 has a peak gain of 2.5dBi at 2.4GHz and efficiencies of 56%, and 4.5dBi and 55% along bands 4.9GHz to 6GHz. This Taoglas patent granted antenna is unique in the market because it is made from poly-flexible material, has a tiny form factor (45*7*.01mm) and has double-sided 3M tape for easy “peel and stick” mounting. The cable routes conveniently directly out of the bottom of the antenna, reducing the volume the antenna takes up in the device to an absolute minimum compared to other designs. The FXP.831 is the ideal all-round antenna solution for squeezing into narrow spaces and still maintaining high performance, for example on the inside top or adjacent side applied directly to the plastic housing of LCD devices. Many module manufacturers specify peak gain limits for any antennas that are to be connected to that module. Those peak gain limits are based on free-space conditions. In practice, the peak gain of an antenna tested in free-space can degrade by at least 1 or 2dBi when put inside a device. So ideally you should go for a slightly higher peak gain antenna than mentioned on the module specification to compensate for this effect, giving you better performance. Upon testing of any of our antennas with your device and a selection of appropriate layout, integration technique, or cable, Taoglas can make sure any of our antennas’ peak gain will be below the peak gain limits. Taoglas can then issue a specification and/or report for the selected antenna in your device that will clearly show it complying with the peak gain limits, so you can be assured you are meeting regulatory requirements for that module. For example, a module manufacturer may state that the antenna must have less than 2dBi peak gain, but you don’t need to select an embedded antenna that has a peak gain of less than 2dBi in free space. This will give you a less optimized solution. It is better to go for a slightly higher free-space peak gain of 3dBi or more if available. Once that antenna gets integrated into your device, performance will degrade below this 2dBi peak gain due to the effects of GND plane, surrounding components, and device housing. If you want to be absolutely sure, contact Taoglas and we will test. Choosing a Taoglas antenna with a higher peak gain than what is specified by the module manufacturer and enlisting our help will ensure you are getting the best performance possible without exceeding the peak gain limits. The cable and connector are fully customizable, for further information contact your regional Taoglas customer support team. 1. Introduction 1. Introduction 1. Introduction 1. Introduction 1. Introduction 1. Introduction 1. Introduction 1. Introduction 4 SPE-11-8-026-J www.taoglas.com Electrical Frequency 2.4 ~ 2.5GHz, 4.9 ~ 6.0GHz Peak Gain (free space) 2.5dBi 4.5dBi Peak Gain (on plastic*) 3.0dBi 5.5dBi Average Gain (free space) -2.6dBi -2.6dBi Average Gain (on plastic) -2.6dBi -1.8dBI Efficiency (free space) 56% 55% Efficiency (on plastic) 56% 75% VSWR ≦2.5 : 1 Impedance 50 Ohms Polarization Linear Radiation Pattern Omni Input Power 2W max. Mechanical Dimensions 45mm x 7mm Antenna Body Material Polymer Cable Gray 100mm 1.37 co-axial Connector Ipex MHF ENVIRONMENTAL Temperature Range -40°C to 85°C Humidity Non-condensing 65°C 95% RH 2. Specifications 3. Antenna Characteristics2. Specifications 3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics2. Specifications 3. Antenna Characteristics2. Specifications 3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics2. Specifications 5 SPE-11-8-026-J www.taoglas.com 3.1 S11 3. Electrical Characteristic 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics -45 -40 -35 -30 -25 -20 -15 -10 -5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Freq(GHz) S11(dB) Free space with 1.0mm ABS with 1.5mm ABS with 2.0mm ABS 6 SPE-11-8-026-J www.taoglas.com 3.1 3.2 Test setup A ETS AMS-8500 test chamber is used for the free space radiation testing for FXP831.07.0100A. The measurement is taken with the antenna properly mounted in the designated device. Device tested in AMS-8500 Rectangular test chamber. 7 SPE-11-8-026-J www.taoglas.com 3.2 Peak Gain 0 1 2 3 4 5 6 7 8 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 4200 4400 4600 4800 5000 5200 5400 …

Text truncated - open the document above for the full version.

Report No.: AAEMT/RF/251104-01-03 Page | 1 Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 FCC Test Report Part 15 Subpart C FCC ID：2AM8R-D810A Client Information: *Applicant: Netradyne Inc *Applicant add.: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122 Product Information: Sampling Details..................: The below Test Item provided by applicant *EUT Name: Driveri *Model No.: D-810 *Brand Name: *Series Model: D-810A, D-811 Standards: FCC PART 15 Subpart C: 2015 section 15.247 AA Electro Magnetic Test Laboratory Private Limited Add. : Plot No 174, Udyog Vihar - Phase 4, Sector 18, Gurgaon, Haryana, India Date of Receipt: Nov. 04, 2025 Date of Test: Nov. 04 ~ Dec. 08, 2025 Date of Issue: Dec. 29, 2025 Test Result: Pass Declaration of Conformity: Disclaimer: The * Information are provided by Manufacturer and it is verified through the Request form and Marking Label, AA Electro Magnetic Test Laboratory is not responsible for the above information accuracy. This device described above has been tested by AA Electro Magnetic Test Laboratory Private Limited, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. *This test report must not be used by the client to claim product endorsement by any agency of the U.S. government. Prepared By (+ signature) Rakhi Garg: Reviewed & Approved by: (+ signature) Ankur Kumar : Declaration of conformity of the results is based as per the standard limits Report No.: AAEMT/RF/251104-01-03 Page | 2 Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 1 Contents Page COVER PAGE 1 CONTENTS 2 2 VERSION 2 3 TEST SUMMARY 4 3.1 COMPLIANCE WITH FCC PART 15 SUBPART C 4 3.2 MEASUREMENT UNCERTAINTY 5 3.3 TEST LOCATION 5 4 TEST FACILITY 6 4.1 DEVIATION FROM STANDARD 6 4.2 ABNORMALITIES FROM STANDARD CONDITIONS 6 5 GENERAL INFORMATION 7 5.1 GENERAL DESCRIPTION OF EUT 7 5.2 EUT PERIPHERAL LIST 9 5.3 TEST PERIPHERAL LIST 9 6 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 7 TEST RESULT 12 7.1 DESCRIPTION OF TEST CONDITIONS 12 7.2 ANTENNA REQUIREMENT 13 7.3 CONDUCTION EMISSIONS MEASUREMENT 14 7.4 RADIATED EMISSIONS MEASUREMENT 18 7.5 6 DB BANDWIDTH 47 7.6 MAXIMUM PEAK OUTPUT POWER 57 7.7 PEAK POWER SPECTRAL DENSITY 60 7.8 BAND EDGES REQUIREMENT 71 7.9 CONDUCTED SPURIOUS EMISSIONS 77 Report No.: AAEMT/RF/251104-01-03 Page | 3 Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 2 Version Revision Record Version Chapter Date Modifier Remark -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Report No.: AAEMT/RF/251104-01-03 Page | 4 Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 3 Test Summary 3.1 Compliance with FCC Part 15 subpart C TEST TEST REQUIREMENT TEST METHOD RESULT Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PASS Conducted Emissions at Mains Terminals FCC PART 15 C section 15.207 ANSI C63.10: Clause 6.2 PASS Radiated Spurious Emission (30 MHz to 25 GHz) FCC PART 15 C section 15.209 &15.247(d) ANSI C63.10: Clause 6.4, 6.5 and 6.6 PASS 6 dB Bandwidth FCC PART 15 C section 15.247 (a)(2) ANSI C63.10: Clause 6.9.1 PASS Maximum Peak Output Power FCC PART 15 C section 15.247(b)(3) FCC/KDB-558074 D01 v03r01 Clause 9.1.2 PASS Peak Power Spectral Density FCC PART 15 C section 15.247(e) ANSI C63.10: Clause 6.11.2.3 PASS Band Edges Measurement FCC PART 15 C section 15.247 (d) &15.205 FCC/KDB-558074 D01 v03r01 Clause 13.3.1 PASS Conducted Spurious Emission (30MHz to 25GHz) FCC PART 15 C section 15.209 &15.247(d) ANSI C63.10: Clause 6.7 PASS Remark: N/A: not applicable. Refer to the relative section for the details. EUT: In this whole report EUT means Equipment Under Test. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radio Frequency. ANSI C63.10: the detail version is ANSI C63.10:2020 in the whole report. Report No.: AAEMT/RF/251104-01-03 Page | 5 Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 3.2 Measurement Uncertainty All measurements involve certain levels of uncertainties, the following measurements uncertainty Levels have estimated based on standards, the maximum value of the uncertainty as below: No. Item Uncertainty 1 Conducted Emiss…

Text truncated - open the document above for the full version.

Report No.: AAEMT/RF/251104-01-01 1 | P a g e Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 FCC Test Report Part 15 subpart C FCC ID: 2AM8R-D810A Client Information: *Applicant: Netradyne Inc *Applicant add.: 9171 Towne Centre Drive, Suite 110, San Diego, CA 92122 Product Information: Sampling Details..................: The below Test Item provided by applicant *EUT Name: Driveri *Model No.: D-810 *Brand Name: *Series Model: D-810A, D-811 Standards: FCC PART 15 Subpart C: 2013 section 15.247 AA Electro Magnetic Test Laboratory Private Limited Add. : Plot No 174, Udyog Vihar - Phase 4, Sector 18, Gurgaon, Haryana, India Date of Receipt: Nov. 04, 2025 Date of Test: Nov. 04 ~ Dec. 05, 2025 Date of Issue: Dec. 29, 2025 Test Result: Pass Declaration of Conformity: Declaration of conformity of the results is based as per the standard limits Disclaimer: The * Information are provided by Manufacturer and it is verified through the Request form and Marking Label, AA Electro Magnetic Test Laboratory is not responsible for the above information accuracy. This device described above has been tested by AA Electro Magnetic Test Laboratory Private Limited, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. *This test report must not be used by the client to claim product endorsement by any agency of the U.S. government. Prepared By (+ signature) Rakhi Garg: Reviewed & Approved by: (+ signature) Ankur Kumar : Report No.: AAEMT/RF/251104-01-01 2 | P a g e Plot No.174, UdyogVihar Phase 4, Sector -18, Gurgaon -122016, Haryana, India Contact: 0124-4235350, 4145343; e-mail: info @aaemtlabs.com; Website: www.aaemtlabs.com Decision Rule Used: Simple Acceptance (i.e., w = 0, Acceptance Limit = Tolerance Limit) as Per ILAC-G8:09/2019 AAEMT/A2LA/TRF/ FCC-15C/24_01_REV0 AA Electro Magnetic Test Laboratory Private Limited Certificate#5593.01 1 Contents Page COVER PAGE 1 CONTENTS ............................................................................................................................................................................. 2 2 VERSION ................................................................................................................................................................................. 4 3 TEST SUMMARY .................................................................................................................................................................. 5 3.1 COMPLIANCE WITH FCC PART 15 SUBPART C .................................................................................................................... 5 3.2 MEASUREMENT UNCERTAINTY .......................................................................................................................................... 6 3.3 TEST LOCATION ................................................................................................................................................................. 6 4 TEST FACILITY .................................................................................................................................................................... 7 4.1 DEVIATION FROM STANDARD ............................................................................................................................................. 7 4.2 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................................................ 7 5 GENERAL INFORMATION................................................................................................................................................. 8 5.1 GENERAL DESCRIPTION OF EUT ........................................................................................................................................ 8 5.2 EUT PERIPHERAL LIST ..................................................................................................................................................... 10 5.3 TEST PERIPHERAL LIST .................................................................................................................................................... 10 6 EQUIPMENTS LIST FOR ALL TEST ITEMS ................................................................................................................ 11 7 TEST RESULT ...................................................................................................................................................................... 13 7.1 DESCRIPTION OF TEST CONDITIONS .................................................................................................................................. 13 7.2 ANTENNA REQUIREMENT ................................................................................................................................................. 14 7.2.1 Standard requirement .............................................................................................................................................. 14 7.2.2 EUT Antenna .......................................................................................................................................................... 14 7.3 CONDUCTION EMISSIONS MEASUREMENT ........................................................................................................................ 15 7.3.1 Applied procedures / Limit ..................................................................................................................................... 15 7.3.2 Test procedure .......…

Text truncated - open the document above for the full version.