2AMLF-VL103DLTE Vehicle Terminal

VL103 LTE Vehicle Terminal USER MAN V U 1 A .1 L Product overview GNSS indicator Network indicator Power indicator SIM card slot On/off switch Real-time tracking Driving behavior analysis (4 types) Serial port (optional) Over-speed alert SOS alert Tamper alert Removal alert Power-supply-cut alert Low power alert Vibration alert Geo-fence Item VL103 Power cable (Length:1m) Relay Panic button Quantity 1 1 Optional Optional Specif ication Network Frequency 4G & 2G VL103D (L): LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B28 GSM: B2/B3/B5/B8 VL103D (E) LTE-FDD: B1/B3/B7/B8/B20/B28 LTE-TDD: B34/B38/B39/B40/B41 GSM: B2/B3/B5/B8 Location accuracy Relay TTFF (open sky) <10 meters CEP Optional Avg. hot start≤1sec Avg. cold start≤32sec Indication GPS (Blue), Cellular (Green), Power (Red) Battery Operating voltage Operating temperature 270 mAh, 3.7V Li-Polymer battery 9-90VDC –20 °C to +70 °C Device weight 55 g Device dimension 92 mm*40 mm*20 mm Product Setup 1. Prepare a micro SIM card that supports the same network with this device. 2. Remove the shell of device. 3. Insert SIM card into the slot and toggle the switch to ON. LED Indication Power Status (Red) On for 0.3s and off for 0.3s On for 1s and off for 3s On for 0.1s and off for 3s Solid on Off Low power Fully charged Working normally Charging (Higher priority than the status of low power) Battery is exhausted/Internal failure GNSS Status (Blue) On for 0.3s and off for 0.3s Searching GNSS signal Solid on Positioned GNSS module is in sleep mode or not working Cellular Status (Green) On for 0.3s and off for 0.3s On for 1s and off for 3s On for 0.1s and off for 3s Solid on Off Network initializing Receiving signal normally Network connected Calling No signal received/No SIM card detected Power supply Status (Red, Blue, Green) Red, Blue and Green on for 3s Connected/disconnected power supply Off Interfaces 8 Pin Standard Version Interface Color Description V+ Red Power + (9-90V) V- Black Power - Ground pin ACC Orange Vehicle ignition detection Relay Yellow Cut-off vehicle fuel supply SOS+ White SOS Trigger Pin SOS- Black SOS Ground Pin Data A Blue RS485 Date B Green RS485 Wiring of Standard Version Tips for finding right wires: 1. Use multimeter to find out the positive and negative sides of vehicle battery. Note: No matter the ignition key is switched to ON or OFF, current battery voltage can be shown in the multimeter. 2. The way to find ACC wire: Connect multimeter’s black probe to negative side, and connect red probe to a random wire, at this moment, the voltage shown in multimeter is 0V; turn the key to ON, if the supply voltage is shown, that’s the correct ACC wire. 3. Connect the two connectors together, if the vehicle has no connector, please connect device’s wires to corresponding vehicle wires. Installation recommendation Please install the device under the guidance of professional personnel. Near the head light Inside the taillight cover or the plastic component Inside the pedal Under the back seat Inside the headlight cover around the speed meter Inside the taillight cover Under the pedal Inside the front cover Under rear windshield Note: 1. The device should face up to sky. 2. Metal thermal barrier or heating layer, which are always installed on windshield, may affect the signal, please avoid installing the device under these objects. Platform & APP 1. Login service platform Please login the designated service platform to set and operate the device. 2. Download APP Please download and install the APP in designated website, APP store or Google Play store. Around dashboard Under front hood SMS Commands VERSION# STATUS# Query the firmware version Query the status PARAM# Query parameters (IMEI, SOS numbers, center number, and time zone) WHERE# Query the current location URL# Query the location link URL# Network connected and position fixed: <05-22 10:53> http://maps.google.com/maps? q=N23.111712,E114.409264 Network not connected but position fixed: <05-2210:53> http://maps.google.com/maps? q=N23.111712,E114.409264 Network not connected and position not fixed: NO DATA! GPRSSET# Query network parameters (GPRS status, APN, server address, URL, etc.) GPRSSET# GPRS,ON;Currently use APN:CMnet,,;APN Auto set:OFF; SERVER,1,test.topstargps.com, 11139;URL, http://maps.google.com/maps?q= APN# Set APN parameters APN, apnname# OR APN, apnname,user,pwd# Close automatic APN and set by yourself. APN# Check the current APN parameters. SERVER# Set the parameters of the monitoring server SERVER,mode,domainName/IP, port,protocol# eg:SERVER,1,www.ydpat.com, 8011,0# SERVER,0,211.154.135.113, 8011,0# mode = 1 means set with domain name mode = 0 means set with ip address protocol = 0 means connect server with TCP protocol protocol = 1 means connect server with UDP protocol SERVER# Check the current sever parameters SOS# Set SOS numbers SOS,A,phone number 1,phone number 2,phone number 3# Add SOS phone number. SOS,D,sequence number 1, sequence number 2,sequence number 3# Delete the phone number according to the sequence number. SOS,D,phone number# Delete the matching SOS phone number. SOS# Check the SOS phone number. TIMER# Set the time interval for the GNSS module to send data TIMER,T1,T2# T1=5~18000 or 0, upload interval when ACC ON, unit: seconds; 0 means no upload; default is 10; T2=5~18000 or 0, upload interval when ACC OFF,unit: seconds; 0 means no upload; default is 10. TIMER# Check the current parameters of T1 and T2. RELAY# Control the power and fuel RELAY,A# A=0/1;0 means connection, 1 means cut off;default: 0. RELAY# Check the status of the control. ADT# Set parameters to upload voltage values of the external battery ADT,A,T# A=ON/OFF, On/Off ADC data upload,default: Off B=5~3600, Default: 600s; Upload time interval,unit: seconds ADT,OFF# Turn off analog data upload ADT# Query the ADT port parameters RESET# The device restarts 20 seconds later after receiving the command. RESET# The device would reboot in 20S after receiving the command. SPEEDCHECK# Set and query th…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 1 of 5 Appendix External Photos for FYCR2211000444AT FCC ID: 2AMLF-VL103D Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 2 of 5 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 3 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 4 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 5 of 5

VL103 LTE VehicleTerminal DATA Cellular LTE-FDD B1/B2/B3/B4/B5/B7/B8/B28 GSM B2/B3/B5/B8 Internal Battery 270mAh 3.7V Li-Polymer Operating Voltage DC 9V to 90V STANDARD INTERFACE IMEI: 357301091884238 (L) 1 2 3 45 6 7 8 1 2 3 4 5 6 7 8 White: SOS Purple: ADC Red: VCC Blue: Data A Black: GND Orange: ACC Yellow: Relay Green: Data B 20mm 4 mm 4 mm 4 mm 3 mm 4 mm FCC ID:2AMLF-VL103D Contains FCC ID:2AMLFXQ600-LA

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 1 of 7 Appendix Internal Photos for FYCR2211000444AT FCC ID: 2AMLF-VL103D Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 2 of 7 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 3 of 7 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 4 of 7 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 5 of 7 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 6 of 7 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 7 of 7 - End of the Appendix -

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 1 of 12 Winkey Wang EMC Technical Manager RF EXPOSURE EVALUATION REPORT Application No.: FYCR2211000444AT Applicant: Shenzhen Jimi IoT Co., Ltd. Address of Applicant: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Manufacturer: Shenzhen Jimi IoT Co., Ltd. Address of Manufacturer: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Factory: Shenzhen Jimi IoT Co., Ltd. Address of Factory: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Equipment Under Test (EUT): EUT Name: LTE Vehicle Terminal Model No.: VL103 Trade Mark: JIMI FCC ID: 2AMLF-VL103D Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2022-11-09 Date of Evaluation: 2022-11-12 to 2022-11-18 Date of Issue: 2022-12-07 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 2 of 12 Revision Record Version Chapter Date Modifier Remark 01 2022-12-07 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 3 of 12 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 General Description of E.U.T. ............................................................................................................ 4 3.2 Details of E.U.T. ................................................................................................................................. 4 3.3 Separation Distance ........................................................................................................................... 5 3.4 Test Location ...................................................................................................................................... 6 3.5 Test Facility ........................................................................................................................................ 6 3.6 Deviation from Standards ................................................................................................................... 6 3.7 Abnormalities from Standard Conditions ........................................................................................... 6 4 FCC Radiofrequency radiation exposure limits .................................................................................... 7 4.1 Blanket 1 mW Blanket Exemption ...................................................................................................... 7 4.2 MPE-based Exemption ...................................................................................................................... 7 4.3 SAR-based Exemption ....................................................................................................................... 8 5 Measurement and Calculation ............................................................................................................... 11 5.1 Maximum transmit power ................................................................................................................. 11 5.2 RF Exposure Calculation ................................................................................................................. 12 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 4 of 12 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power Supply: Input: 9-90V DC Battery information Model: PL432033S Rated voltage: DC 3.7V Capacity: 270mAh 1.0Wh Cable: Power cable 100cm For BLE Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V5.0 LE Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: PIFA Antenna Gain: 1.33dBi For GSM Operation Frequency Band: GSM850/PCS1900 Antenna Type: PIFA antenna Antenna Gain: GSM850: -1.5dBi; PCS1900: 0.7dBi For LTE LTE Operation Frequency Band: LTE Band 2,4,5,7 Antenna Type: PIFA Antenna Antenna Gain: LTE Band 2: 0.7dBi LTE Band 4: 0.7dBi LTE Band 5: -1.5dBi LTE Band 7: 0.7dBi Remark: The information in this section is provided by the applicant or manufacturer, CCS is not liable to the accuracy, suitability, reliability or/and integrity of the information. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 5 of 12 3.3 Separation Distance Minimum test separation distance: 20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044403 Page: 6 of 12 3.4 Test Location All tests were performed at: Compliance Certification Services（Kunshan）Inc. Shenzhen branch. …

Text truncated - open the document above for the full version.

SunnywayTechnology(ShenZhen)Co.Ltd Pagenumber1-9 SPECIFICATION for Antenna SunnywayTechnology(Shenzhen)Co.Ltd CustomerNo.JimiIot ProductNo.Sunnyway SunnywayTechnology(Shenzhen)Co.Ltd 6thFloor,Building5,NantaiyunChuangguCenter,GuangmingDistrict,Shenzhen [email protected] Tel: 86-0755-82504210 Fax:86-02164842328 SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber2-9 Contents SPECIFICATION...................................................................................................................1 SunnywayTechnology(Shenzhen)Co.Ltd ......................................................................... 2 CONTENTS...........................................................................................................................2 1.BILATERALCONFIRMATIONPAGE.........................................................................3 2.GENERAL..................................................................................................................4 3.GENERALPRODUCTSPECIFICATIONS...........................................................4 4.SPECIFICATIONDETIALS...........................................................................................5 4.1MECHANICALPROPERTIES..............................................................................................5 4.2ELECTRICPERFORMANCE.........................................................................................7 5.PRODUCTPACKAGING.........................................................................................9 6.DOCUMENTRESUME............................................................................................9 SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber3-9 1.BilateralConfirmationpage 1.1Customersignature CustomerJimiIot Separtment/post Sign Date HardwareEngineer/RD Mechanical/MD ProjectManager/PM Commercial/Puchasing Checker 1.2SignatureofSunnywayTechnologycompany Separtment/post Sign Date AntennaEngineer/RD Mechanical/MD ProjectManager/PM QA Checker SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen) Co . Ltd Page number4-9 2. General 2.1Scope of application Thisspecificationis onlyapplicableto J i m i I ot L T E antenna 2 . 2 Operatingtemperaturerange Temperaturerange of this product: -20 ~ + 65C 2.3Storagetemperaturerange : This productis stored at - 30 ~ + 75 °C 3 .Generalproductspecifications NO .ITEMSDETAILS 1 Type FPC 2 OperatingFrequency Band BT 2.4 G 3VSWR ≤2.5 4 Max . Gain 1.33dBi 5 RadiationEfficiency≥40 % 6 Impedance 50Ω 7 AntennaType PIFA 8 Antennacomposition N/A 9 EntityPicture SunnywayTech nology(Shenzhen) Co. Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber5-9 4.SpecificationDetials 4.1MechanicalProperties 4.11ProductComposition No. Material Size(MM) 1 FPC 50*12*12Thick0.3mm 4.12Apperance Goodappearancewithoutscars 、 dirts 、 protuberances,etc. 4.13AntennaPictureandStructureDimension Refertoproductdrawings: SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber6-9 SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber7-9 4.2Electric Performance Environment Temperature ： 10 °C ——+30 °C Humidity：≤80%(+40°C) Atmospher：750mmkg±30mmkg Equipment NetworkAnalyzer: AnechiorChamber: AgilentE8358A ETS Maker 24002500 VSWR 2.42 SunnywayTechnology(Shenzhen)Co.Ltd TestDataforElectricalPerformance: 4.22.1S11oftheAntenna: SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber8-9 4.22.2Passivegainefficiency: Frequency/Mhz Efficiency/% MaxGain/dBi 240039.170.93 24104009119 24204285109 243043.251.33 244043.550.84 24504385109 24604159058 247042.851.14 248041.110.81 249039.990.97 25003715067 4.22.3Radiationpattern: SunnywayTechnology(Shenzhen)Co.Ltd SunnywayTechnology(Shenzhen)Co.Ltd Pagenumber9-9 5.Product Mannerofpacking: Packedinselfsealedbags,200pcseach. 6.Document DocumentNo. ReleaseDate2022/11/19 Author PeilinLu Review Huangxiong RevisedHistory DateVersionRevisedRecord 2022/11/19 1.00 NewProject SunnywayTechnology(Shenzhen)Co.Ltd

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044402 Page: 1 of 77 Winkey Wang EMC Technical Manager TEST REPORT Application No.: FYCR2211000444AT Applicant: Shenzhen Jimi IoT Co., Ltd. Address of Applicant: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Manufacturer: Shenzhen Jimi IoT Co., Ltd. Address of Manufacturer: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Factory: Shenzhen Jimi IoT Co., Ltd. Address of Factory: 3-4/F, Block A, Building#7, Shenzhen International Innovation Valley, Dashi 1st Road, Nanshan District ShenZhen China Equipment Under Test (EUT): EUT Name: LTE Vehicle Terminal Model No.: VL103 Trade Mark: JIMI FCC ID: 2AMLF-VL103D Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2022-11-09 Date of Test: 2022-11-12 to 2022-11-18 Date of Issue: 2022-12-07 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044402 Page: 2 of 77 Revision Record Version Chapter Date Modifier Remark 01 2022-12-07 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044402 Page: 3 of 77 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221100044402 Page: 4 of 77 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 6 4.1 DETAILS OF E.U.T. ......................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 6 4.4 TEST LOCATION ............................................................................................................................. 7 4.5 TEST FACILITY ............................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 7 5 EQUIPMENT LIST ............................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................11 6.1 ANTENNA REQUIREMENT ................................................................................................................11 6.1.1 Test Requirement: ..................................................................................................................11 6.1.2 Conclusion ..............................................................................................................................11 7 RADIO SPECTRUM MATTER TEST RESULTS .................................................................................12 7.1 CONDUCTED PEAK OUTPUT POWER ................................................................................................12 7.1.1 E.U.T. Operation .....................................................................................................................12 7.1.2 Test Mode Description ............................................................................................................12 7.1.3 Test Setup Diagram ................................................................................................................13 7.1.4 Measurement Procedure and Data .........................................................................................13 7.2 MINIMUM 6DB BANDWIDTH .....................…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 1 of 3 Appendix Test Setup Photos for FYCR2211000444AT FCC ID: 2AMLF-VL103D Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 2 of 3 Test Setup Photo Radiated Emissions which fall in the restricted bands Radiated Spurious Emissions Below 1GHz Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 3 of 3 - End of the Appendix -