2AMQ8-LTSW6Surge Protector

User Manual 1.Product parameter USB Output DC5V/3.4A（total） E ach USB Output is 2.1A Wireless charging Compatible protocol Output Power Qi- EPP 10W Max Input voltage AC125V/60Hz Protect function Over temperature protection, FOD foreign object detection 2、Description of wireless charging function: 1.Put the mobile phone with wireless charging function (such as iPhone8 /X/11, Samsung Note8/S9+, Huawei ma te20Pro, etc.) to t he c enter of wireless charging， and the charging will start automatically. When the wireless charger is in normal working condition, the LED green light blink slow. The indicator status is described in the following table： sta tus Power-on Standby Charging After full Metal foreign body detection Indicator status bright Always off Breathing state Everbright Flash 1s / time 2. When charging, you need to keep the center position of the phone aligned with the center position of the wireless charger to perform wireless charging. If it is not working properly, please adjust the position of the phone until the phone shows normal charging or the LED green light blink slow. 3.Notes Do not mix met al foreign objects between the p hone and the wireless charger while charging. In order to ensure normal charging, the thickness of the plastic or silicone mobile phone case is less than1-2mm. The material and thickness of the phone case can affect the normal charging function and increase the temperature of the wireless charging. If necessary, remove the phone case for wireless charging. Do not squeeze or bump the product. Do not disassemble or modify it by yourself. Do not place the product near fire or into fire or water. Do not use the wireless charger under severe heat, humidity or corrosive conditions to avoid damage to the circuit. Do not place the magnetic card (ID card, bank card, etc.) with a magnetic strip or chip too close to avoid the magnetic card failure. Keep implanted medical devices (cardiac pacemakers, implantable cochlea, etc.) at least 20 cm away from the wireless charger to avoid potential interference with medical equipment. Children should be taken care to avoid unnecessary accidents. FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undeundesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or mormore of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Company: Ningbo Litesun Electronics Co.,Ltd Add: Simen Town, yuyao, Zhejiang 315472 China Tel: 0086-574-62128318 Fax: 0086-574-62128700 FCC Authorization Date: 2020-07-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Ningbo Litesun Electronics Co.,Ltd, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Printed Name: Ding ganggang Title: Engineer QA-FR-170-B

Compan y Name: Ningbo Litesun Electronics Co.,Ltd Add: Simen Town, yuyao, Zhejiang 315472 China Tel: 0086-574-62128318 Fax : 0086-574-62128700 E-mail: [email protected] FCC Confidential Authorization Date: 2020-07-10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AMQ8-LTSW6 To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Ningbo Litesun Electronics Co.,Ltd hereby requests long-term con fidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Printed Name: Ding ganggang Title: Engineer

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS Antenna

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200710002-00B FCC Part 15C Page 9 of 22 FCC §1.1307& §1.1310& §2.1091 – MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard FCC §1.1307 & 1.1310 & §2.1091 According to the item 5(b) of KDB 680106 D01 RF Exposure Wireless Charging Apps v03: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF evaluation. a) Power transfer frequency is less that 1 MHz. b) Output power from each primary coil is less than or equal to 15 watts. c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. d) Client device is placed directly in contact with the transmitter. e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Limits for Maximum Permissible Exposure (MPE) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 *100 6 3.0-30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 300-1,500 / / f/300 6 1,500-100,000 / / 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f²) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200710002-00B FCC Part 15C Page 10 of 22 EUT Setup Result a) Power transfer frequency is less that 1 MHz. Yes, the device operates in the frequency 110 kHz-205 kHz. b) Output power from each primary coil is less than or equal to 15 watts. Yes, the maximum output power of the primary coil is 5W<15W. c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Yes, the transfer system including a charging system with only single primary coils is to detect and allow only between individual of coils. d) Client device is inserted in or placed directly in contact with the transmitter. Yes, client device is placed directly in contact with the transmitter. e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes, this is a mobile device. f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. The EUT H-field Strength levels at 15 cm surrounding the device and 20 cm above the top surface are less than 50% the MPE limit. Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200710002-00B FCC Part 15C Page 11 of 22 Test Data Environmental Conditions Temperature: 24.2 °C Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Chao Gao on 2020-07-23. H-Field Strength Frequency Range (kHz) Position A (A/m) Position B (A/m) Position C (A/m) Position D (A/m) Position E (A/m) 50% Limit (A/m) Limit Test (A/m) 110-205 0.087 0.049 0.068 0.064 0.234 0.815 1.63 E- Field Strength Frequency Range (kHz) Position A (V/m) Position B (V/m) Position C (V/m) Position D (V/m) Position E (V/m) 50% Limit (V/m) Limit Test (V/m) 110-205 1.910 1.101 1.562 1.432 2.136 307 614 Note: 1: According with KDB 680106 D01 RF Exposure Wireless Charging Apps v03, Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63 A/m. 2: The distance for position A, B, C, D are 15cm, the distance for position E is 20cm.

FCC PART 15C TEST REPORT For Ningbo Litesun Electronics Co.,Ltd Simen Town, yuyao, Zhejiang 315472 China FCC ID: 2AMQ8-LTSW6 Report Type: Original Report Product Type: Surge Protector Test Engineer: Chao Gao Report Number: RSHA200710002-00B Report Date: 2020-08-03 Reviewed By: Oscar Ye EMC Manager Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road,Kunshan,Jiangsu province,China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200710002-00B FCC Part 15C Page 2 of 22 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §1.1307& §1.1310& §2.1091 – MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................ 9 APPLICABLE STANDARD .............................................................................................................................................. 9 EUT SETUP ................................................................................................................................................................ 10 RESULT ...................................................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 11 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 12 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS ..................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 13 TEST PROCEDURE ...................................................................................................................................................... 13 FACTOR & OVER LIMIT CALCULATION ...................................................................................................................... 14 TEST RESULTS SUMMARY .......................................................................................................................................... 14 TEST DATA ................................................................................................................................................................ 14 FCC §15.209 & §15.205 - SPURIOUS EMISSIONS ................................................................................................ 17 APPLICABLE STANDARD ..........................................................................................................................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Conducted Emissions (Front View) Conducted Emissions (Side View) Radiated Emissions View (Below 30MHz) Radiated Emissions View (Above 30MHz) H-Filed Strength View Position A H-Filed Strength View Position B H-Filed Strength View Position C H-Filed Strength View Position D H-Filed Strength View Position E E-Filed Strength View Position A E-Filed Strength View Position B E-Filed Strength View Position C E-Filed Strength View Position D E-Filed Strength View Position E