2AN75-HT018A-1TXHUBSAN HT018A Transmitter

V2.0 Zino 2 《User Manual》 All users must read product operating instructions as well as this liability disclaimer before using any Hubsan product. By using a Hubsan product(s), users are accepting the terms and conditions of Hubsan liability and operational guidelines. This product is not suitable for minors under 14 years of age. While operating a Hubsan product (s), users also accept all liability and responsibility for their own behavior, actions as well as any consequences resulting thereof while using a Hubsan product(s). These products may only be used for purposes that are proper and in accordance with local regulations, terms and any applicable policies / guidelines Hubsan may make avail- able. Users agree to comply with these terms and conditions, along with any and all relevant policies / guidelines set forth by Hubsan. INSTRUCTIONS Some product flight functions are restricted in certain areas. Once you use this prod- uct, you are deemed to have read carefully the relevant ICAO regulations, local airspace control provisions and the regulations governing UAVs. You assume all liability for any non-compliance with the foregoing, are responsible for the conse- quences for your actions as well as any indirect and / or direct liability that arises as a result of these limitations. (1) Select an open environment devoid of high rise buildings and tall obstructions (such as trees and poles). Near buildings and obstacles, flight control signals and GPS signals can be severely weakened; GPS functions such as GPS mode and Return to Home may not function properly. (2) Do not fly in bad weather conditions (such as in wind, rain or fog). (3) Fly the aircraft in ambient temperatures of 0-40 °C. (4) When flying, please stay away from obstructions, crowds, high voltage lines, trees, water, etc. (5) To avoid remote control signal interference, do not fly in complex electromagnet- ic environments (such as venues with radio stations, power plants and towers). (6) The aircraft cannot be used in or near the Arctic circle or Antarctica. (7) Do not fly in no-fly zones. (8) Do not operate the aircraft near high pressure lines, airports or areas with severe magnetic interference. FLIGHT ENVIRONMENT REQUIREMENTS DISCLAIMER & WARNING IMPORTANT SAFETY INFORMATION OPERATION Be extremely careful and responsible when using the aircraft. Small electronic components can be damaged due to crashes or exposure to moisture / liquid. To avoid any injuries, do not use the aircraft with broken or damaged components. MAINTENANCE Do not try to open or repair the units by yourself. Please contact Hubsan or Hubsan authorized dealers for service. For more information, please visit the official website at www.hubsan.com. BATTERY Do not disassemble, squeeze, impact, burn, drop or trample the battery. Do not short-circuit or put the battery terminal in contact with metal. Do not expose the battery to temperatures above 60 ° C. Charge the aircraft battery prior to flight. Use a Hubsan dedicated charger for charging. Keep the battery out of the reach of children and away from any kind of moisture. FLIGHT Please be mindful of personal safety and the safety of others while flying. -Do not fly in bad weather conditions. -Do not attempt to catch the aircraft while it is in flight. -This product is intended for experienced pilots over the age of 14. -After every flight, completely disarm the aircraft motors and disconnect the aircraft from power. Then, you may power off the remote control. READ THE DISCLAIMER AND SAFETY GUIDELINES FIRST BEFORE USE. Symbol Explanation: Prohibited Operation Important Notice Instruction Explanation / Reference HUBSAN AIRCRAFT USES SMART BATTERY 1. Do not disassemble or reassemble the battery. 2. Do not short-circuit the battery. 3. Do not use or charge near sources of heat. 4. Do not put the battery in contact with water or any kind of liquid. 5. Do not charge batteries under sunlight or near fire. 6. Do not puncture or subject the battery to force of any kind. 7. Do not throw or manhandle the battery. 8. Never charge a battery that has been damaged, become deformed or swelled. 9. Do not solder on or near the battery. 10. Do not reverse charge or over discharge the battery. 11. Do not reverse charge or reverse the battery polarities. 12. Do not connect the battery to a car charger / cigarette lighter or any kind of unconventional power source. 13. This battery is prohibited for non-designated devices. 14. Do not mix other types of batteries with lithium batteries. 15. Do not exceed the specified charging time. 16. Do not place the battery in a microwave or in areas of high pressure. 17. Do not expose the battery to the sun. 18. Do not use in environments with high static electricity (64V and above). 19. Do not use or charge in temperatures below 0 °C and above 45 °C. 20. If a newly purchased battery is used, leaking, possesses a bad smell or other abnormalities, return immediately to the vendor. 21. Keep away from the reach of children. 22. Use a dedicated battery charger and follow all charging requirements. 23. Minors who use the battery and its dedicated unit must be supervised by an adult at all times. ● If you do not plan to fly the aircraft for a long time, store the battery ~50% charged to maintain battery performance and life. ● Please use Hubsan chargers for battery charging. ● Discharge the battery at 5C current or below. To avoid discharge related battery damage, do not prolong the discharge time. ● Do not charge on carpet to avoid fire. ● Batteries need to be recharged if unused for over 3 months. Important safety information Battery use precautions Disclaimer 1 Aircraft 1.1 Aircraft Spare Part 1.2 Aircraft Battery 1.2.1 Aircraft Battery Charging 1.2.2 Aircraft Battery Installation 1.2.3 Intelligent Flight Battery Function 1.2.4 Precautions For Low Tempera- ture 1.2.5 Precautions For Battery 1.3 Propellers 2 Remote Controller（America Mode 2） 2.1 Names Of Remote Controller Compo- nents 2.2 Re…

Text truncated - open the document above for the full version.

Date: 04/17/2018 VCB_F-01: Operating Procedures Form – FCC Confidentiality v02 Page 1 of 1 SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AN75-HT018A-1TX Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name 1. Block Diagram, 2. Schematics, 3. Operational Description 1. 2AN75-HT018A-1TX -Block diagram 2. 2AN75-HT018A-1TX -SCH 3. 2AN75-HT018A-1TX -Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of xxxx (ie- “45”, “90” or “180”) days: Exhibit Type File Name N/A N/A Signature: Contact name: Judy Wu Company name: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054

Date: 04/17/2018 VCB_F-01: Operating Procedures Form – FCC Authorization v02 Page 1 of 1 SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2020/3/10 SUBJECT: FCC Application for (FCC ID: 2AN75-HT018A-1TX) To Whom It May Concern: We, the undersigned, hereby authorize Aaron Ma in Shenzhen Huaxia Testing Technology Co., Ltd at 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen Huaxia Testing Technology Co., Ltd on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, (Must be signed by the person that is listed on the FCC Website) Signature: Contact name: Judy Wu Company name: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054

FCC ID:2AN75-HT018A-1TX FCC ID:2AN75-HT018A-1TX FCC ID:2AN75-HT018A-1TX FCC ID:2AN75-HT018A-1TX

FCC ID: 2AN75-HT018A-1TX FCC ID: 2AN75-HT018A-1TX FCC ID: 2AN75-HT018A-1TX FCC ID: 2AN75-HT018A-1TX FCC ID: 2AN75-HT018A-1TX FCC ID: 2AN75-HT018A-1TX

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building,Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax:+86-755-26648637 Website:www.cqa-cert.com Report Template Version: V04 Repor tTemplate Revision Date: 2018-07-06 RF Exposure Evaluation Report The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Report No. : CQASZ20200300118E-02 Applicant: SHENZHEN HUBSAN TECHNOLOGY CO., LTD Address of Applicant:13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 Equipment Under Test (EUT): Product: HUBSAN HT018A Transmitter Model No.: HT018A Brand Name: HUBSAN FCC ID:2AN75-HT018A-1TX Standards: 47 CFR Part 1.1307 47 CFR Part 1.1310 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2020-03-06 Date of Test: 2020-03-06 to 2020-03-12 Date of Issue: 2020-03-12 Test Result :PASS* *In the configuration tested, the EUT complied with the standards specified above Tested By： (Tom chen) Reviewed By: (Aaron Ma) Approved By: (JackAi) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-02 Page: 2 of 7 1Version Revision History Of Report ReportNo.Version Description Issue Date CQASZ20200300118E-02Rev.01 Initial report 2020-03-12 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-02 Page: 3 of 7 2 Contents Page 1 VERSION......................................................................................................................................................................2 2CONTENTS..................................................................................................................................................................3 3 GENERAL INFORMATION........................................................................................................................................4 3.1 C LIENTINFORMATION................................................................................................................................................4 3.2 G ENERALDESCRIPTION OFEUT................................................................................................................................4 4 SAR EVALUATION.....................................................................................................................................................5 4.1 RF E XPOSURECOMPLIANCEREQUIREMENT..............................................................................................................5 4.1.1 Standard Requirement..................................................................................................................................5 4.1.2 Limits................................................................................................................................................................5 4.2 EUT RF E XPOSUREEVALUATION..............................................................................................................................6 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-02 Page: 4 of 7 3 General Information 3.1 Client Information Applicant: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address of Applicant: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 Manufacturer: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address of Manufacturer: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 3.2 General Description of EUT Product Name: HUBSAN HT018A Transmitter Model No.: HT018A Trade Mark: HUBSAN Hardware version: EA04058034-04 Software version: V0.1.1 Operation Frequency: IEEE 802.11a: 5725MHz ~5850 MHz Channel Numbers: IEEE 802.11a: 5725MHz ~5850MHz/ 5 channel Type of Modulation: IEEE 802.11a: OFDM(64QAM, 16QAM, QPSK, BPSK) Channel Separation: IEEE 802.11a: 20 MHz Transmitter Operating channel width(OCW) ≤20MHz (provider declaration) Sample Type: MobilePortableFix Location Test Software of EUT: Atheros Radio test 2 (manufacturer declare) Antenna Type: Integral antenna Antenna Gain: ANT1: 3.0dBi ANT2: 3.0dBi Power Supply: Battery: 3.6V 3350 mAh Li-Po Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-02 Page: 5 of 7 4 SAR Evaluation 4.1RF Exposure Compliance Requirement 4.1.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 4.1.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)]≤3.0 for 1-g SAR and≤7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 17 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-02 Page: 6 of 7 4.2 EUT RF Exposure Evaluation 1) For 5G WIFI Antenna Gain: ANT1: 3.0dBi, ANT2: 3.0dBi Antenna Gain: The maximum Gain measured in fully anechoic chamber is 2.0 in linear sca…

Text truncated - open the document above for the full version.

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building,Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax:+86-755-26648637 Website:www.cqa-cert.com Report Template Version: V04 Report Template Revision Date: 2018-07-06 Test Report The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full. Report No. : CQASZ20200300118E-01 Applicant: SHENZHEN HUBSAN TECHNOLOGY CO., LTD Address of Applicant:13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 Equipment Under Test (EUT): Product: HUBSAN HT018A Transmitter Model No.: HT018A Brand Name: HUBSAN FCC ID:2AN75-HT018A-1TX Standards: 47 CFR Part 15, Subpart E KDB 789033 D02 General UNII Test Procedures New Rules v02 KDB 558074 D01 Meas Guidance v05 Date of Receipt: 2020-03-06 Date of Test: 2020-03-06 to 2020-03-12 Date of Issue: 2020-03-12 Test Result :PASS* *In the configuration tested, the EUT complied with the standards specified above Tested By： (Tom chen) Reviewed By: (Aaron Ma) Approved By: ( Jack Ai) Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-01 Page: 2 of 45 1Version Revision History Of Report Report No.Version Description Issue Date CQASZ20200300118E-01Rev.01 Initial report 2020-03-12 Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-01 Page: 3 of 45 2TestSummary Test ItemTest RequirementTest methodResult Antenna Requirement 47 CFR Part 15 Subpart C Section 15.203 ANSI C63.10-2013PASS AC Power Line Conducted Emission 47 CFR Part 15 Subpart E Section 15.407 (b)(6) ANSI C63.10-2013PASS Conducted Output Power and transmit power control mechanism 47 CFR Part 15 Subpart E Section 15.407 (a)(1)(2)(4)(h)(1) ANSI C63.10-2013PASS Emission Bandwidth 47 CFR Part 15 Subpart E Section 15.407 (a)(1)(2) ANSI C63.10-2013PASS Peak Power Spectral Density 47 CFR Part 15 Subpart E Section 15.407 (a)(1)(2)(5) ANSI C63.10-2013PASS Frequency stability 47 CFR Part 15 Subpart E Section 15.407 (g) ANSI C63.10-2013PASS Operation in the absence of information to the transmit 47 CFR Part 15 Subpart E Section 15.407 (c) 47 CFR Part 15 Subpart EPASS Radiated Spurious Emissions 47 CFR Part 15 Subpart E Section 15.407 (b)(1)(2)(3)(5) (6)(7)(8) ANSI C63.10-2013PASS Restricted bands around fundamental frequency (Radiated Emission) 47 CFR Part 15 Subpart E Section 15.407 (b)(6)(7)(8) ANSI C63.10-2013PASS Remark: The tested sample(s) and the sample information are provided by the client. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radiated Frequency. CH: In this whole report CH means channel. Volt: In this whole report Volt means Voltage. Temp: In this whole report Temp means Temperature. Humid: In this whole report Humid means humidity. Press: In this whole report Press means Pressure. Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20200300118E-01 Page: 4 of 45 3 Content 1 VERSION....................................................................................................................................................................... 2 2 TEST SUMMARY......................................................................................................................................................... 3 3CONTENT...................................................................................................................................................................... 4 4 TEST REQUIREMENT.................................................................................................................................................5 4.1 T EST SETUP........................................................................................................................................................... 5 4.1.1 For Conducted test setup.............................................................................................................................. 5 4.1.2 For Radiated Emissions test setup.............................................................................................................. 5 4.1.3 For Conducted Emissions test setup...........................................................................................................6 4.2 T ESTENVIRONMENT..............................................................................................................................................6 4.3 T ESTCONDITION....................................................................................................................................................7 5 GENERAL INFORMATION.........................................................................................................................................8 5.1 C LIENTINFORMATION............................................................................................................................................8 5.2 G ENERALDESCRIPTION OFEUT......................................................................................................................... 8 5.3 P RODUCTSPECIFICATION SUBJECTIVE TO THIS STANDARD...............................................................................8 5.4 D ESCRIPTION OFSUPPORTUNITS....................................................................................................................... 9 5.5 T ESTLOCATION...................................................................................................................................................10 5.6 T ESTFACILITY..................................................................................................................................................... 10 5.7 D EVIATION FROMSTANDARDS..............…

Text truncated - open the document above for the full version.

FCC ID:2AN75-HT018A-1TX Radiated spurious emission Test Setup-1(Below 30MHz) Radiated spurious emission Test Setup-2(30MHz-1GHz) FCC ID:2AN75-HT018A-1TX Radiated spurious emissionTest Setup-3(Above 1GHz) Conducted Emissions Test Setup