2ANKDJCP35W7Wireless charger

Scan for product webpage For assembly assistance, contact us at (800) 349-3839 or [email protected] ©2026 UPLIFT Desk®. All Rights Reserved. Patent Pending Wireless Charging Grommet JCP35W7 Assembly Instructions Product Components Wireless Module (1) Housing (1) Locking Ring (1) Power Adapter (1) The installation of the Wireless Charging Grommet requires a hole through the desktop measuring 3.15" (80mm) in diameter and a maximum desktop thickness of 1.75". If there are any damaged or missing parts, please contact us at (800) 349-3839 or [email protected]. Step 1 Unscrew the Locking Ring from the Housing. Step 2 Remove the Wireless Module from the Housing. 2 Step 3 Insert the Housing into the grommet hole. Step 4 Thread the Locking Ring onto the Housing and tighten until it is firmly against the underside of the desktop. The Locking Ring should rotate smoothly when properly engaged with threads. If it does not, it may be cross-threaded. Remove it and try again. Step 5 Feed the Wireless Module’s power cable through the top of Housing. 3 Align the legs on the Wireless Module with one of the four sets of grooves in the Housing per the height positions shown in the diagrams. Top view of HousingSide view of Housing 1 1 2 3 4 1 2 3 4 1 2 3 4 2 3 4 4 3 2 4 2 Step 4 - Secure Locking Ring Thread the Locking Ring onto the Housing and tighten until it is Ģ%    !   Note: : 2 8 !    % # %   #    /         %     8"   %   Step 5 - Insert Wireless Module Position 1 ,!   ! Position 2 6  !   Top view of Housing 1 1 1 2 2 2 2 2 3 3 3 4 4 4 1 3 3 4 4 , =3!D#  !   Housing. Align the legs on the Wireless Module with one of the four sets of grooves in the Housing per the height positions shown in the diagrams. Side view of Housing Position 3 6  ! ! JLNˆEPF   Position 4 6  ! ! JMSˆEKJF   Step 6 Plug the Power Adapter cord into the Wireless Module cord. Desktop Use The Wireless Module can be removed from the housing and placed closer for easier access. Rubber feet on the ends of the legs protect the desktop from scratches and keep the module from sliding. Plug the Power Adapter into a 120V power outlet. If you are using a height adjustable desk or table, make sure there is enough slack in the power cord to reach the Wireless Charging Grommet when the desk or table is raised. 5 Center the device on the charger. Charging will be most efficient when the ambient temperature is below 77° F. Temperatures greater than 95° F may result in an auto-shutoff until the Wireless Module has cooled. Spacing greater than 0.25” between the device and charger (such as with thick phone cases) may prevent or slow charging. Read all Safety & Warnings and Wireless Product Information at the end of this manual before use. Wireless charging Charging & Toubleshooting Information 6 Read all instructions before assembly. Failure to assemble or operate properly may result in damage or personal injury. Retain manual for future reference or new owners. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • For indoor use only. Use only in dry areas. • This product must be installed and used in accordance with all appropriate electrical codes and regulations. • Avoid getting any liquid on or in the product, as it can cause shock and fire. If the product gets wet, disconnect the product from power. Ensure the product is completely dry before reconnecting to power. • Do not attempt to open the product or attempt to perform service on the product. Dangerous voltages are present inside the components during operation. • Never operate the product if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged. • Avoid placing any card with a magnetic strip on the charger as it could be damaged by the charger. • For safe charging, remove all items from the charging area, including phone cases, pop sockets, coins, keys, rings, staples, paper clips, RFID cards, credit cards, and any metal objects. Metal objects near the charging pad can become hot and potentially cause burns. • Ensure the charging area is clear and free from dust and other debris prior to use. • Use and store the product only within the specified temperature ranges. Avoid high temperatures and direct sunlight, and keep away from open flames and other heat sources. Excess heat will affect performance and may result in damage to the product. • Do not attempt to disassemble, repurpose, or modify the product in any way. • Do not use near industrial equipment or aboard an aircraft. • DO NOT USE IF YOU HAVE A PACEMAKER OR OTHER IMPLANTED MEDICAL DEVICE. Wireless charging may disrupt the operation of these devices. • The distance between the wireless product and the user should be at least 7.9 in (20 cm) when installed and operated. • Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from improper use of this product. Safety & Warnings 7 upliftdesk.com [email protected] (800) 349-3839 (512) 614-3152 This product complies with following FCC standards: FCC 15.207 - AC Line Conducted Emission FCC 15.209, 15.205 - Radiated Emission Test FCC 15.203 - Antenna Requirement FCC 1.1310, 2.1091 - Maximum Permissible Exposure (MPE) FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter…

Text truncated - open the document above for the full version.

ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD. Add: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, XINCHANG COUNTY, China Tel: +0086-575-86297980 Email: [email protected] Attestation Letter Date: 2026-07-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: Our product Wireless charger, model: JCP35W7, PDC020, FCC ID:2ANKDJCP35W7, for marketing purpose, this product only supports 110.5-205kHz, 360-365kHz . The other functions, bands and modes was disabled to use by manufacturer in the software, the end user h as no capability to activate it. Sincerely, Printed Name: YONG MA Title: Manager

ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD. Add: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, XINCHANG COUNTY, China Tel: +0086-575-86297980 Email: [email protected] CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 2026-07-03 FE DERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii)Filing FCC ID:2ANKDJCP35W7 ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD.certifies that the equipment for which authorization is sought is not“covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD.certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD .certifies that the equipment does not use Kaspersky's software information. Sincerely, Sig nature : Prin ted Name: YONGMA Title: Manager

CFR 47 §2.911(d)(7) U.S Agent U.S. AGENT LETTER OF ATTESTATION Date: 2026-9- 4 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2ANKDJCP35W7 Zhejiang Jiecang Linear Motion Technology Co.,Ltd. certifies that, as of the date of the filing of the application, J -Star Motion is our designated U.S. agent for service of process for the above referenced FCC ID. Zhejiang Jiecang Linear Motion Technology Co.,Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. J-Star Motion accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: J-Star Motion Address: 13617 Woodlawn Hills Dr Cedar Springs, MI 49319 United States FRN: 0033411976 Tel.: 616.540.8278 Email: [email protected] Signed by (printed name): Jacob Dornan Signature: Applicant: Zhejiang Jiecang Linear Motion Technology Co.,Ltd. Add: No.19 XinTao Road, Provincial High Tech Park,XinChang county,ZheJiang Province,China FRN: 0026796037 Tel: 0086-875-86297980 Email: [email protected] Signed by (printed name): YONG MA Signature:

QA-FR-170-B ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD . Add: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, XINCHANG COUNTY, China Tel: +0086-575-86297980 Email: [email protected] FCC Authorization Date:2026-07-03 FEDER AL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Su bject: Agent Authorization To w hom it may concern: ZHE JIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD ., Hereby authorizes China Certification ICT Co., Ltd (Dongguan)to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thi s authorization is valid until further written notice from the applicant. Si ncerely Yours, Client’s signature: Pr inted Name: YONGMA Title: Manager

QA-FR-171- A ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD . Add: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, XINCHANG COUNTY, China Tel: +0086-575-86297980 Email: [email protected] FCC Confidential Authorization Date: 2026-07-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ANKDJCP35W7 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD . ) hereby requests long-term confidential treatment of information accompanying this application as outlined below: •Bloc k Diagram •Schematics •Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Prin ted Name: YONGMA Title: Manager

ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD. Add: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, XINCHANG COUNTY, China Tel: +0086-575-86297980 Email: [email protected] DECLARATION OF SIMILARITY Date: 2026-07-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD., hereby declare that the product: Wireless charger, FCC ID: 2ANKDJCP35W7, model: PDC020 is electrically identical with the model: JCP35W7 which was t ested by China Certification ICT Co., Ltd (Dongguan). A description of the differences between those models and that are declared similar areas follows: They are the same product, and just different with the model names of distribution chains, the rest are the same. Please contact me should there be need for any additional clarification or information. Best Regards, Signature: Printed Name: YONG MA Title: Manager

China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 1 / 9 EUT EXTERNAL PHOTOGRAPHS JCP35W7 PDC020 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 2 / 9 JCP35W7 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 3 / 9 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 4 / 9 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 5 / 9 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 6 / 9 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 7 / 9 PDC020 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 8 / 9 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-EXP Page 9 / 9 *****END *****

China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-INP Page 1 / 3 EUT INTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-INP Page 2 / 3 China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-INP Page 3 / 3 Coil Antenna *****END *****

China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Report Template: RF-FCC-15C-A/0 Page 42 of 47 5. MAXIMUM PERMISSIBLE EXPOSURE (MPE) 5.1 Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According with 680106 D01 Wireless Power Transfer v04 clause 3.2 Accordingly, for § 2.1091-Mobile devices, the MPE limits between 100 kHz to 300 kHz are to be considered the same as those at 300 kHz in Table 1 of § 1.1310, that is, 614 V/m and 1.63 A/m, for the electric field and magnetic field, respectively. For § 2.1093-Portable devices below 4 MHz and down to 100 kHz, the MPE limits in § 1.1310 (with the 300 kHz limit applicable all the way down to 100 kHz) can be used for the purpose of equipment authorization in lieu of SAR evaluations. According to 680106 D01 Wireless Power Transfer v04 clause 5.2 There might be situations where the WPT RF emissions are limited enough that even operations in a “crowded” environment, where many similar WPT devices are present, do not pose significant EMC and RF exposure concerns. In this scenario, and for devices operating within a one-meter distance from the receiver, as defined above, a manufacturer will not have to submit an “Equipment Compliance Review” KDB, and receive FCC concurrence before proceeding with equipment authorization. This exception to the requirement of submitting the ECR to obtain FCC concurrence only applies when all the following criteria (1) through (6) are met: (1) The power transfer frequency is below 1 MHz. (2) The output power from each transmitting element (e.g., coil) is less than or equal to 15 watts. (3) A client device providing the maximum permitted load is placed in physical contact with the transmitter (i.e., the surfaces of the transmitter and client device enclosures need to be in physical contact) (4) Only § 2.1091-Mobile exposure conditions apply (i.e., this provision does not cover § 2.1093-Portable exposure conditions). China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Report Template: RF-FCC-15C-A/0 Page 43 of 47 (5) The E-field and H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit, per KDB 447498, Table 1. These measurements shall be taken along the principal axes of the device, with one axis oriented along the direction of the estimated maximum field strength, and for three points per axis or until a 1/d (inverse distance from the emitter structure) field strength decay is observed. Symmetry considerations may be used for test reduction purposes. The device shall be operated in documented worst-case compliance scenarios (i.e., the ones that lead to the maximum field components), and while all the radiating structures (e.g., coils or antennas) that by design can simultaneously transmit are energized at their nominal maximum power. (6) For systems with more than one radiating structure, the conditions specified in (5) must be met when the system is fully loaded (i.e., clients absorbing maximum power available), and with all the radiating structures operating at maximum power at the same time, as per design conditions. If the design allows one or more radiating structures to be powered at a higher level while other radiating structures are not powered, then those cases must be tested as well. For instance, a device may use three RF coils powered at 5 W, or one coil powered at 15 W: in this case, both scenarios shall be tested. 5.2 Block Diagram of Test Setup 5.3 Test Procedures 1) Perform H-field and E-field measurements for each all sides of the EUT at 20cm, along all the principal axes defined with respect to the orientation of the transmitting element(e.g., coil or antenna). 2) The highest emission level was recorded and compared with limit. 3) The EUT was measured according to 680106 D01 Wireless Power Transfer v04 20 cm China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Report Template: RF-FCC-15C-A/0 Page 44 of 47 5.4 Test Data Sample Number: 3PK3-1 Test Date: 2026/7/16 Test Site: EMI Test Mode: M1 Tester: Ella Huang Test Result: Pass Environmental Conditions: Temperature: (°C) 24.5 Relative Humidity: (%) 51 ATM Pressure: (kPa) 100 Test Equipment List and Details: Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Narda Electric and Magnetic Field Probe-Analyzer EHP-200AC 180ZX10204 2023/9/1 2026/8/31 * Statement of Traceability: China Certification ICT Co., Ltd (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). H-Field Strength: Frequency Range (kHz) Position A (A/m) Position B (A/m) Position C (A/m) Position D (A/m) Position E (A/m) Position F (A/m) 50% Limit (A/m) Limit (A/m) 111 0.159 0.198 0.193 0.173 0.367 0.168 0.815 1.63 364 0.0111 0.0117 0.0121 0.0116 0.0116 0.0119 0.815 1.63 E-Field Strength: Frequency Range (kHz) Position A (V/m) Position B (V/m) Position C (V/m) Position D (V/m) Position E (V/m) Position F (V/m) 50% Limit (V/m) Limit (V/m) 111 1.78 2.03 1.66 1.62 3.59 0.78 307 614 364 1.34 2.32 2.15 2.52 1.81 0.65 307 614 Note: Test with 20cm distance from the center of the probe(s) to the edge of the device. China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Repor…

Text truncated - open the document above for the full version.

TEST REPORT Applicant: ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD Address: No.19 XinTao Road, Provincial High Tech Park, XinChang county, ZheJiang Province, China 312500 FCC ID: 2ANKDJCP35W7 Product Name: Wireless charger Standard(s): 47 CFR Part 15, Subpart C ANSI C63.10-2013 The above device has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: 2603V21733E-RF-00A Date Of Issue: 2026/7/29 Reviewed By: Calvin Chen Title: RF Test Supervisor Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) Room 101 & 201, Building 2, 256 Pingdong Road, Dalang Town, Dongguan City, Guangdong, China. Tel: +86-769-83085888 www.ccttt.com.cn China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Report Template: RF-FCC-15C-A/0 Page 2 of 47 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the Room 101 & 201, Building 2, 256 Pingdong Road, Dalang Town, Dongguan City, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. Each test item follows the test standard(s) without deviation. China Certification ICT Co., Ltd (Dongguan) Report No.: 2603V21733E-RF-00A Report Template: RF-FCC-15C-A/0 Page 3 of 47 CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 1. GENERAL INFORMATION ................................................................................................................................... 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 5 1.1.1 General ........................................................................................................................................................... 5 1.1.2 Antenna Information Detail▲ ....................................................................................................................... 5 1.1.3 Accessory Information ................................................................................................................................... 5 1.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 6 1.2.1 EUT Operation Condition .............................................................................................................................. 6 1.2.2 Support Equipment List and Details .............................................................................................................. 6 1.2.3 Support Cable List and Details ...................................................................................................................... 6 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 6 1.3 MEASUREMENT UNCERTAINTY .............................................................................................................................. 8 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 9 3. REQUIREMENTS AND TEST PROCEDURES ................................................................................................. 10 3.1 AC LINE CONDUCTED EMISSIONS ........................................................................................................................ 10 3.1.1 Applicable Standard ..................................................................................................................................... 10 3.1.2 EUT Setup.................................................................................................................................................... 11 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 11 3.1.4 Test Procedure ............................................................................................................................................. 12 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 12 3.2 RADIATED EMISSIONS .......................................................................................................................................... 13 3.2.1 Applicable Standard ..................................................................................................................................... 13 3.2.2 EUT Setup............................................................................................…

Text truncated - open the document above for the full version.

China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP Radiated Emission 30MHz-1GHz View Radiated Emission 9kHz-30MHz Parallel View China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP Radiated Emission 9kHz-30MHz Perpendicular View Radiated Emission 9kHz-30MHz Ground-parallel View China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP E-Field Position A E-Field Position B China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP E-Field Position C E-Field Position D China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP E-Field Position E E-Field Position F China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP H-Field Position A H-Field Position B China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP H-Field Position C H-Field Position D China Certification ICT Co., Ltd (Dongguan) EXHIBIT No.: 2603V21733E-RF-00A-TSP H-Field Position E H-Field Position F *****END *****