2ANRDFEWL08wireless winch remote control

Wireless Operation 1. Activate the Wireless Remote by pressing the IN/OUT button for 3 seconds until LED lights up. 2. Press IN or OUT to operate Winch. 3. To turn off the Wireless Remote, keep pressing the IN/OUT button for 3 seconds until LED turns off. The Wireless Remote will automatically power off after 2 minutes of inactivity. Wireless Operation Precautions 1. Do not use near sources of radio interference or other remote control systems. They may interfere with operation or cause unexpected operation. 2. If Wire Rope unexpectedly moves, reverses, or stops, disconnect Battery Cable from Circuit Breaker immediately to prevent serious injury from sudden Wire Rope movement. 3. Only use Wireless Remote while Winch, Fairlead, Wire Rope, and object being winched/anchor point are all clearly in view. 4. Do not use more than one Remote Transmitter near a Receiver. Additional Transmitters should be turned off and be stored with their batteries removed to prevent accidental operation. 5. Do not use a damaged or malfunctioning Wireless Remote. If Wireless Remote does not work properly, discontinue use immediately and remove its batteries. Wireless Remote Control Battery Replacement 1. Remove Screw(s) and open battery compartment. 2. Insert new battery or batteries in correct polarity. 3. Close compartment and replace Screw(s). FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Important Note: RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process : Company Name: QPS America, Inc. FRN: 0033412354 Contact Name: Jose Luis Medina Address: 5005 Rockside Road, Suite 600, Independence, Ohio 44131-6827 Telephone No: 216-377-3191 Email: [email protected] Applicant: Company name: Hangzhou Rock Machinery Manufacture Co., Ltd. Product Description: wireless winch remote control FRN:0026837559 FCC ID:2ANRDFEWL08 Contact Name: Chunhong Jiang Address: No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Telephone No:0086-571-87191226 Email: [email protected] Hangzhou Rock Machinery Manufacture Co., Ltd. certifies that, as of the date of this filing of the application with the TCB, [QPS America, Inc.] is our designated US agent for service of process for the above referenced FCC ID. Hangzhou Rock Machinery Manufacture Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [QPS America, Inc.] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2025/08/14 Applicant’s Name:Chunhong JiangUS Agent’s Name: Jose Luis Medina Title:ManagerTitle: Managing Director Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 Hangzhou Rock Machinery Manufacture Co., Ltd. TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Hangzhou Rock Machinery Manufacture Co., Ltd. Grantee code: 2ANRD FCC ID: 2ANRDFEWL08 FRN: 0026837559 Contact Name: Chunhong Jiang Address: No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Telephone No: 0086-571-87191226 Fax No: 0086-571-87191227 Email: [email protected] i. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2025/08/14 Applicant’s Name: Chunhong Jiang Title: Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

HangzhouRockMachineryManufactureCo.,Ltd. Code00018768Ed.1 Item1.Thedevicei sabletoi nstallsoftware/programi nstallation? ☐ Yes,got oItem2. ☒No.Int hiscase,therestofthei temsdonotapply.Thedevicecannotsupport installationofKasperskycybersecurityoranti-virussoftware. Item2.TechnicalRequirementsf orKasperskyCybersecuritySoftware: #GeneralRequirements(ForallDevices)Yes/ Noor N/A Comments N/A 1Internetconnectionforactivationandupdates(Forall OperatingSystems) Device wirelesswinchremotecontrol Companyname HangzhouRockMachineryManufactureCo.,Ltd. Granteecode 2ANRD FCCID 2ANRDFEWL08 FRN 0026837559 Contactname ChunhongJiang Address No.1,1stRoad,DongzhouIndustrialZone, Fuyang311400,Hangzhou,China Telephonenumber 0086-571-87191226 E-mail [email protected] 2317B Chipset/moduleinformation OperatingSystem(ifapplicable) N/A StorageCapacity(harddriveor otherpermanentmemorystorage, ifapplicable) N/A 2 #GeneralRequirements(ForWindowsDevices)Yes/ Noor N/A Comments N/A 1Storage:1500MBf reespaceontheharddrive N/A 2OperatingSystem: MicrosoftWindows8,8.1,10&11Home/Pro/ EnterpriseMicrosoft Windows7Starter/HomeBasic&Premium/ Professional/ UltimateSP1orhigher N/A 3Processor:1GHzorhigher(x86orx64) N/A 4Memory(RAM)1GB(32-bit)or2GB(64-bit) N/A 5ScreenResolution:Minimumresolutionof1024x768 #GeneralRequirements(FormacOSdevices)Yes/ Noor N/A Comments N/A 1OperatingSystemmacOS®13–14 N/A 2Memory(RAM)4GB N/A 3Storage:3455MBf reespaceontheharddrive #GeneralRequirements(ForAndroidDevices)Yes/ Noor N/A Comments N/A 1Storage:150MBf reespace N/A 2OperatingSystem:Android™10–14 3 N/A 3ScreenResolution:Minimumresolutionof320x480 #GeneralRequirements(fori OSdevices)Yes/ Noor N/A Comments N/A 1Storage:150MBf reespace N/A 2OperatingSystem:i OS®17 #GeneralRequirements(ForLinuxsystem)Yes/ Noor N/A Comments 1Harddrive:1GBoffreespaceN/A 2CPU:I ntelPentium1GHzorhigher 3RAM:1GB 4Minimumsoftwarerequirements: AlmaLinuxOS8orl ater; AlterOS7.5orl ater; AstraLinuxCommonEdition2.12orl ater; CentOS6.7orl ater; DebianGNU/Linux10.0orl ater; EulerOS2.0orl ater; OracleLinux7.3orl ater; RedHatEnterpriseLinux6.7orl ater; RockyLinux8.5orl ater; SUSELinuxEnterpriseServer12.5orl ater; Ubuntu12.04orl ater; UncomOSHome/Business/Education/Enterprise 2.2orl ater; 4 ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐Yes, go to Item 3. ☒No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3.Connectivity Capabilities: #Physical InterfacePurposeJustification 1 1 #Wireless InterfacePurposeJustification 1 1 After the review of this items, the device: ☒Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third-party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature:Name: Chunhong Jiang Date: 2025.08.14 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications.

TCB CALL página 1 File FCC ID: 2ANRDFEWL08 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://businesssearch.ohiosos.gov?=businessDetails/1961919 TCB CALL página 2 In google: Official wenbsite: https://qpsamerica.com/ TCB CALL página 3 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter - 2ANRDFEWL08-s" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter -2ANRDFEWL08" >

C5266091_X10_Ed.2 1/1 HangzhouRockMachineryManufactureCo.,Ltd. OfficeofEngineeringTechnology FederalCommunicationsCommission ☐ 7435OaklandMillsRoad Columbia,MD21046 Date:2025-08-14 Subject:RequestforConfidentiality FCCID:2ANRDFEWL08 ToWhomItMayConcern, Pursuantt ot hep rovisionso fS ections0 .457a nd0 .459o fC ommission'sr ules (47CFR0.457,0 .459),wea rer equestingt heCommissiont owithholdt hef ollowing attachment(s)asconfidentialdocumentfrompublicdisclosure. ExhibitsLong-Term Confidentiality Short-Term Confidentiality NOTE2 IDLabel/LocationNoNo AttestationStatementNoNo ExternalPhotosNo ☐ BlockDiagram ☒☐ Schematics ☒☐ TestReportNoNo TestSetupPhotosNo ☐ User’sManual ☐ NOTE 1 ☐ InternalPhotos ☐ NOTE 1 ☐ PartsList/TuneUp ☐ RFExposureInfoNoNo OperationalDescription ☒☐ CoverLetter(s)NoNo SDRSoftware/SecurityInfo ☐ No NOTE1:Long-TermConfidentialitymaybepermittedunderspecialconditions(SeeI I.LONG-TERMCONFIDENTIALITY,Section3of KDB726920,uselasti nforce) NOTE2:Short-TermConfidentialitycanberequestedforamaximumof180daysfromthedateofthegrant. Abovementioneddocumentc ontainsdetaileds ystemandequipmentdescriptionare considereda sp roprietaryi nformationi no perationo ft hee quipment.T hep ublic disclosureo fa boved ocumentsmightb eh armfult oo urc ompanya ndwouldg ive competitoranunfairadvantagei nthemarket. Incaseofshort-termConfidentiality,theapplicantrequestst heexhibitsselectedabove arewithheldf rompublicviewf oraperiodof______daysf romt hedateoft heGrant ofEquipmentAuthorizationandpriortomarketing. Iti sourunderstandingt hatallmeasurementt estr eports,FCCI Dl abelf ormatand correspondentduringc ertificationr eviewprocessc annotbegranteda sc onfidential documentsandt hosei nformationwillbeavailablef orpublicr eviewoncet hegrantof equipmentauthorizationi si ssued. Sincerely, ChunhongJiang

Hangzhou Rock Machinery Manufacture Co., Ltd. C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Hangzhou Rock Machinery Manufacture Co., Ltd. Address: No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name: wireless winch remote control Model Number: FEWL08 FCC Identifier: 2ANRDFEWL08 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Chunhong Jiang Date: 2025-08-14 Title: Manager Signature of applicant:

Document No: SHE25070071-01 Page 1 of 4 FEWL08 External Photo All view of EUT Top view of EUT Document No: SHE25070071-01 Page 2 of 4 Bottom view of EUT Front view of EUT Document No: SHE25070071-01 Page 3 of 4 Back view of EUT Left view of EUT Document No: SHE25070071-01 Page 4 of 4 Right view of EUT

Document No: SHE25070071-01 Page 1 of 1 Label Location

Document No: SHE25070071-01 Page 1 of 2 FEWL08 Internal Photo Open view of EUT Internal view of EUT-1 Antenna Document No: SHE25070071-01 Page 2 of 2 Internal view of EUT-2

RF EXPOSURE EVALUATION REPORT Report No.: SHE25070071-01CE Date: 2025-08-13 Page 1 of 10 Applicant : Hangzhou Rock Machinery Manufacture Co., Ltd. Address of Applicant : No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name : wireless winch remote control Brand Name : Rock Model Name : FEWL08 Sample No. : E25070071-01#01 FCC ID : 2ANRDFEWL08 Standards : FCC Part 2.1093 Date of Receipt : 2025-07-25 Date of Test : 2025-07-29~2025-08-13 Date of Issue : 2025-08-13 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Erik Yang) (Jennifer Zhou) (Authorized signatory: Echo Mu) RF EXPOSURE EVALUATION REPORT Report No.: SHE25070071-01CE Date: 2025-08-13 Page 2 of 10 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.3 DETAILS OF EUT ........................................................................................................................................................................ 3 2 ASSESSMENT METHODS .................................................................................................................................................... 4 3 CONCLUSION ......................................................................................................................................................................... 5 4 APPENDIXES .......................................................................................................................................................................... 6 4.1 SAMPLE PHOTOGRAPH............................................................................................................................................................... 6 RF EXPOSURE EVALUATION REPORT Report No.: SHE25070071-01CE Date: 2025-08-13 Page 3 of 10 1 General Information 1.1 Testing Laboratory Company Name ICAS Testing Technology Services (Shanghai) Co., Ltd. Address No.1298, Pingan Road, Minhang District, Shanghai, China Telephone 0086 21-51682999 Fax 0086 21-54711112 Homepage www.icasiso.com 1.2 Details of Application Applicant Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Applicant Company Address No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Contact Person Chunhong Jiang Telephone 0086-571-87191226 Email [email protected] Manufacturer Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Manufacturer Company Address No.1, 1st Road, Dongzhou Industrial Zone,Fuyang 311400, Hangzhou, China Factory Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Factory Company Address No.1, 1st Road, Dongzhou Industrial Zone,Fuyang 311400, Hangzhou, China 1.3 Details of EUT Product Name wireless winch remote control Brand Name Rock Test Model Name FEWL08 FCC ID 2ANRDFEWL08 Operation Frequency 315MHz Modulation Type ASK Antenna Type Integral Antenna Antenna Gain -5dBi Hardware Version V02 Software Version V01 Note: 1. The above information was declared by the manufacture. 2. For more details, please refer to the User’s manual of the EUT. RF EXPOSURE EVALUATION REPORT Report No.: SHE25070071-01CE Date: 2025-08-13 Page 4 of 10 2 Assessment methods According to KDB 447498 D04 Interim General RF Exposure Guidance v01 Appendix B Exemptions for Single RF Sources SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum time-averaged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP20cm is per Formula (B.1). RF EXPOSURE EVALUATION REPORT Report No.: SHE25070071-01CE Date: 2025-08-13 Page 5 of 10 The example values shown in Table B.2 are for illustration only. Test Data Mode 315MHz ASK Field strength (dBuV/m) 84.61dBuV/m(peak)@3m Peak Power (dBm) -10.59 Note: This report listed the worst case value, please ref…

Text truncated - open the document above for the full version.

TEST REPORT Report No.: SHE25070071-01AE Date: 2025-08-13 Page 1 of 27 Applicant : Hangzhou Rock Machinery Manufacture Co., Ltd. Address of Applicant : No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name : wireless winch remote control Brand Name : Rock Model Name : FEWL08 Sample No. : E25070071-01#01 FCC ID : 2ANRDFEWL08 Standards : FCC CFR47 Part 15, Subpart C Section 15.231 Date of Receipt : 2025-07-25 Date of Test : 2025-07-29~2025-08-13 Date of Issue : 2025-08-13 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Erik Yang) (Jennifer Zhou) (Authorized signatory: Echo Mu) TEST REPORT Report No.: SHE25070071-01AE Date: 2025-08-13 Page 2 of 27 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.3 DETAILS OF EUT ........................................................................................................................................................................ 3 1.4 TEST METHODOLOGY ................................................................................................................................................................. 4 1.5 TEST SUMMARY .......................................................................................................................................................................... 4 2 TEST CONDITION .................................................................................................................................................................. 5 2.1 ENVIRONMENTAL CONDITIONS ................................................................................................................................................... 5 2.2 EQUIPMENT LIST ........................................................................................................................................................................ 5 2.3 MEASUREMENT UNCERTAINTY................................................................................................................................................... 5 3 TEST SET-UP AND OPERATION MODES ........................................................................................................................ 6 3.1 DETAILS OF TEST MODE ............................................................................................................................................................ 6 3.2 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ................................................................................................................ 6 3.3 SUPPORT SOFTWARE ................................................................................................................................................................. 6 3.4 TEST SETUP DIAGRAM ............................................................................................................................................................... 6 4 TEST RESULTS ...................................................................................................................................................................... 7 4.1 TRANSMITTER REQUIREMENT & TEST SUITES .......................................................................................................................... 7 4.1.1 Antenna Requirement ....................................................................................................................................................... 7 4.1.2 Provision For Momentary Operation ............................................................................................................................... 8 4.1.3 Duty Cycle Correction Factor ......................................................................................................................................... 10 4.1.4 Radiated Emission ........................................................................................................................................................... 13 4.1.5 20dB Bandwidth ............................................................................................................................................................... 20 5 APPENDIXES ........................................................................................................................................................................ 22 5.1 PHOTOGRAPHS OF THE SAMPLE .............................................................................................................................................. 22 5.2 PHOTOGRAPHS OF THE TEST SET-UP ..................................................................................................................................... 27 TEST REPORT Report No.: SHE25070071-01AE Date: 2025-08-13 Page 3 of 27 1 General Information 1.1 Testing Laboratory Company Name ICAS Testing Technology Service (Shanghai) Co., Ltd. Address No.1298, Pingan Road, Minhang District, Shanghai, China Telephone 0086 21-51682999 Fax 0086 21-54711112 Homepage www.icasiso.com 1.2 Details of Application Applicant Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Applicant Company Address No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Contact…

Text truncated - open the document above for the full version.

Length:358mm OperatingFrequency:315MHz Gain:-5dBi Manufacturer:HangzhouChunboElectronicsTechnologyCo.,Ltd. Address: 5thFloor,Building1,No.11JiaqiRoadXianlinSubdistrict,YuhangDistrictHangzhou City, ZhejiangProvinceChina

Document No: SHE25070071-01 Page 1 of 1 1.1 Set-up for Spurious Emissions below 1GHz 1.2 Set-up for Spurious Emissions above 1GHz