2ANRDFEWL14wireless winch remote control

OPERATION MANUAL WIRELESS REMOTE TRANSMITTER FEWL14 “OK” KEY “CHOOSE” BUTTON OPERATION 1. SWITCH ON: IPS LCD “HOME” KEY BATTERY CHARGING PORT SOCKET for WIRE REMOTE CONTROL COB LIGHT COB LIGHT SWITCH SAFETY INDUCTIVE SWITCH(inside) Presson “HOME” and “OK” key simultaneously for 3 seconds, main interface enters IPS LCD. 2. OPERATION or SETTING: Push up or down “CHOOSE” BUTTON to select “winching” icon or “gear(setting)” icon,then press ‘‘OK” KEY to confirm. 3. WINCHING: When the hand fully holds the transmitter, the SAFETY INDUCTIVE SWITCH is triggered and the word SAFETY turns to orange color from grey color. Push UP or DOWN to pull IN or pull OUT. NOTE: When WIRE REMOTE CONTROL is connected to both TRANSMITTER and RECEIVER, the wireless remote control is automaticly transfered to wire remote control, SAFETY INDUCTIVE SWITCH and “CHOOSE” BUTTON stop functioning simultaneously. 4. SETTING: After selecting “GEAR(SETTING” icon, push “CHOOSE” BUTTON up or down to select what you required, press “OK” KEY to confirm: SYNCING------Programming. Programming must be fulfilled in 3 seconds after the TRANMITTER is powered in. In 3 seconds the TRANSMITTER will be powered off. To get into SYNCING interface, the above steps have to be repeated. BRIGHTNESS------Brightness adjusting on IPS LCD Push “CHOOSE” BUTTON up or down to select brightness accordingly. Press “OK” KEY to confirm. NIGHT MODE------Night mode selecting on IPS LCD Push “CHOOSE” BUTTON up or down to select or guit NIGHT MODE. Press “OK” KEY to confirm. 5. COB LIGHT: Switch on or off COB light. 6. Switch off WIRELESS REMOTE TRANSMITTER: Presson “HOME” and “OK” key simultaneously for 3 seconds, WIRELESS REMOTE TRANSMITTER is switched off. Or WIRELESS REMOTE TRANSMITTER will automaticly switch off in 3 minutes standby. 7. Battery Charging: Connect changing cord(provided) to CHARGING PORT to charge the battery in TRANSMITTER. FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Important Note: RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Hangzhou Rock Machinery Manufacture Co., Ltd. Code 00018768 Ed. 1 Item 1. The device is able to install software/program installation? ☐ Yes, go to Item 2. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A Device wireless winch remote control Company name Hangzhou Rock Machinery Manufacture Co., Ltd. Grantee code 2ANRD FCC ID 2ANRDFEWL14 FRN 0026837559 Contact name Chunhong Jiang Address No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Telephone number 0086-571-87191226 E-mail [email protected] Chipset/module information CMT2380P64 Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A # General Requirements (For Linux system) Yes / No or N/A Comments 3 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher 3 RAM: 1 GB 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐ Yes, go to Item 3. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3. Connectivity Capabilities: 4 # Physical Interface Purpose Justification 1 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒ Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Chunhong Jiang Date: 2026.03.23 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications.

TCB CALL página 1 File FCC ID: 2ANRDFEWL14 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://apps.dos.ny.gov/publicInquiry/EntityDisplay Google: TCB CALL página 2 State of New York department of State: TCB CALL página 3 TCB CALL página 4 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter"

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 Hangzhou Rock Machinery Manufacture Co., Ltd. TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Hangzhou Rock Machinery Manufacture Co., Ltd. Grantee code: 2ANRD FCC ID: 2ANRDFEWL14 FRN: 0026837559 Contact Name: Chunhong Jiang Address: No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Telephone No: 0086-571-87191226 Fax No: 0086-571-87191227 Email: [email protected] i. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Hangzhou Rock Machinery Manufacture Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2026/03/23 Applicant’s Name: Chunhong Jiang Title: Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

C5266091_X10_Ed.2 1/1 Hangzhou Rock Machinery Manufacture Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2026-03-23 Subject: Request for Confidentiality FCC ID: 2ANRDFEWL14 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Chunhong Jiang

Hangzhou Rock Machinery Manufacture Co., Ltd. C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Hangzhou Rock Machinery Manufacture Co., Ltd. Address: No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name: wireless winch remote control Model Number: FEWL14 FCC Identifier: 2ANRDFEWL14 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Chunhong Jiang Date: 2026-03-23 Title: Manager Signature of applicant:

Document No: SHE25110041-01 Page 1 of 3 FEWL14 External Photo Top view of EUT Bottom view of EUT Document No: SHE25110041-01 Page 2 of 3 Front view of EUT Back view of EUT Document No: SHE25110041-01 Page 3 of 3 Left view of EUT Right view of EUT

Document No: SHE25110041-01 Page 1 of 1 Label Location

Document No: SHE25110041-01 Page 1 of 7 FEWL14 Internal Photo Open view-1 of EUT Open view-2 of EUT Document No: SHE25110041-01 Page 2 of 7 Internal view-1 of EUT Internal view-2 of EUT Document No: SHE25110041-01 Page 3 of 7 Internal view-3 of EUT Internal view-4 of EUT Document No: SHE25110041-01 Page 4 of 7 Internal view-5 of EUT Internal view-6 of EUT Document No: SHE25110041-01 Page 5 of 7 Internal view-7 of EUT Internal view-8 of EUT Document No: SHE25110041-01 Page 6 of 7 Internal view-9 of EUT Battery view of EUT Document No: SHE25110041-01 Page 7 of 7 Antenna Position Antenna

RF EXPOSURE EVALUATION REPORT Report No.: SHE25110041-01CE Date: 2026-03-27 Page 1 of 15 Applicant : Hangzhou Rock Machinery Manufacture Co., Ltd. Address of Applicant : No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name : wireless winch remote control Brand Name : Rock Model Name : FEWL14 Sample No. : E25110041-01#02 FCC ID : 2ANRDFEWL14 Standards : FCC Part 2.1093 Date of Receipt : 2025-11-18 Date of Test : 2025-11-18~2026-03-27 Date of Issue : 2026-03-27 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Erik Yang) (Jennifer Zhou) (Authorized signatory: Echo Mu) RF EXPOSURE EVALUATION REPORT Report No.: SHE25110041-01CE Date: 2026-03-27 Page 2 of 15 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.3 DETAILS OF EUT ........................................................................................................................................................................ 3 2 ASSESSMENT METHODS .................................................................................................................................................... 4 3 CONCLUSION ......................................................................................................................................................................... 5 4 APPENDIXES .......................................................................................................................................................................... 6 4.1 EXTERNAL PHOTO OF THE SAMPLE ........................................................................................................................................... 6 4.2 INTERNAL PHOTO OF THE SAMPLE ............................................................................................................................................ 9 RF EXPOSURE EVALUATION REPORT Report No.: SHE25110041-01CE Date: 2026-03-27 Page 3 of 15 1 General Information 1.1 Testing Laboratory Company Name Shanghai Ingeer Testing Technology Co., Ltd. Address No.1298, Pingan Road, Minhang District, Shanghai, China Telephone 0086 21-51682999 1.2 Details of Application Applicant Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Applicant Company Address No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Contact Person Chunhong Jiang Telephone 0086-571-87191226 Email [email protected] Manufacturer Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Manufacturer Company Address No.1, 1st Road, Dongzhou Industrial Zone,Fuyang 311400, Hangzhou, China Factory Company Name Hangzhou Rock Machinery Manufacture Co., Ltd. Factory Company Address No.1, 1st Road, Dongzhou Industrial Zone,Fuyang 311400, Hangzhou, China 1.3 Details of EUT Product Name wireless winch remote control Brand Name Rock Test Model Name FEWL14 FCC ID 2ANRDFEWL14 Operation Frequency 315MHz Modulation Type ASK Antenna Type Integral Antenna Antenna Gain -7dBi Hardware Version V1.3 Software Version V1.0 Note: 1. The above information was declared by the manufacture. 2. For more details, please refer to the User’s manual of the EUT. RF EXPOSURE EVALUATION REPORT Report No.: SHE25110041-01CE Date: 2026-03-27 Page 4 of 15 2 Assessment methods According to KDB 447498 D04 Interim General RF Exposure Guidance v01 Appendix B Exemptions for Single RF Sources SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum time-averaged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP20cm is per Formula (B.1). RF EXPOSURE EVALUATION REPORT Report No.: SHE25110041-01CE Date: 2026-03-27 Page 5 of 15 The example values shown in Table B.2 are for illustration only. Test Data Value 315MHz ASK Field stre…

Text truncated - open the document above for the full version.

TEST REPORT Report No.: SHE25110041-01AE Date: 2026-03-27 Page 1 of 36 Applicant : Hangzhou Rock Machinery Manufacture Co., Ltd. Address of Applicant : No.1, 1st Road, Dongzhou Industrial Zone, Fuyang 311400, Hangzhou, China Product Name : wireless winch remote control Brand Name : Rock Model Name : FEWL14 Sample No. : E25110041-01#02 FCC ID : 2ANRDFEWL14 Standards : FCC CFR47 Part 15, Subpart C Section 15.231 Date of Receipt : 2025-11-18 Date of Test : 2025-11-18~2026-03-27 Date of Issue : 2026-03-27 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Erik Yang) (Jennifer Zhou) (Authorized signatory: Echo Mu) TEST REPORT Report No.: SHE25110041-01AE Date: 2026-03-27 Page 2 of 36 Contents 1 GENERAL INFORMATION ......................................................................................................................................................................3 1.1 TESTING LABORATORY...................................................................................................................................................................................3 1.2 DETAILS OF APPLICATION..............................................................................................................................................................................3 1.3 DETAILS OF EUT .............................................................................................................................................................................................3 1.4 TEST METHODOLOGY .....................................................................................................................................................................................4 1.5 TEST SUMMARY ...............................................................................................................................................................................................4 2 TEST CONDITION.......................................................................................................................................................................................5 2.1 ENVIRONMENTAL CONDITIONS......................................................................................................................................................................5 2.2 EQUIPMENT LIST..............................................................................................................................................................................................5 2.3 MEASUREMENT UNCERTAINTY .....................................................................................................................................................................6 3 TEST SET-UP AND OPE RATION M ODES .......................................................................................................................................7 3.1 DETAILS OF TEST MODE ................................................................................................................................................................................7 3.2 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ..............................................................................................................................7 3.3 SUPPORT SOFTWARE.....................................................................................................................................................................................7 3.4 TEST SETUP DIAGRAM ...................................................................................................................................................................................8 4 TEST RESULTS ...........................................................................................................................................................................................9 4.1 TRANSMITTER REQUIREMENT & TEST SUITES..........................................................................................................................................9 4.1.1 Antenna Requi rem ent .....................................................................................................................................................................9 4.1.2 Provision For Momentary Operation ....................................................................................................................................... 10 4.1.3 Duty Cycle Correction Factor .................................................................................................................................................... 12 4.1.4 Radi ated Emission ........................................................................................................................................................................ 14 4.1.5 20dB Bandwidth ............................................................................................................................................................................. 21 4.2 MAINS EMISSIONS ........................................................................................................................................................................................ 23 4.2.1 AC power-line conducted emissions....................................................................................................................................... 23 5 APPENDIXES............................................................................................................................................................................................. 26 5.1 EXTERNAL PHOTO OF THE SAMPLE..............................................................…

Text truncated - open the document above for the full version.

Length:135.8mm OperatingFrequency:315MHz Gain:-5dBi Manufacturer:HangzhouChunboElectronicsTechnologyCo.,Ltd. Address:5thFloor,Building1,No.11JiaqiRoadXianlinSubdistrict,YuhangDistrictHangzhou City, ZhejiangProvinceChina

Document No: SHE25110041-01 Page 1 of 2 1.1 Set-up for Spurious Emissions below 1GHz 1.2 Set-up for Spurious Emissions above 1GHz Document No: SHE25110041-01 Page 2 of 2 1.3 AC power-line conducted emission Test Setup