2ANTI-T18Remote control

Before Use This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Changzhou Smoothies Electronics Co., Ltd. Add: No. 91, Hanjiang West Road, Xinbei District, Changzhou China Date: 2020-06-03 Dear Sir/Madam, We, Changzhou Smoothies Electronics Co., Ltd. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Remote control Model no.: T18, T18 PRO, T18 PLUS , T18 SE, T18 LITE Sincerely, (Signed) Name / Title: MING ZHU /Manager Company: Changzhou Smoothies Electronics Co., Ltd. Address: No. 91, Hanjiang West Road, Xinbei District, Changzhou China Phone: +86-0519-69815194 Fax: +86-0519-69815195 E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 <2020-06-02> TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2ANTI-T18 T18, T18 PRO, T18 PLUS , T18 SE, T18 LITE For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, (Signed) Name / Title: MING ZHU /Manager Company: Changzhou Smoothies Electronics Co., Ltd. Address: No. 91, Hanjiang West Road, Xinbei District, Changzhou China Phone: +86-0519-69815194 Fax: +86-0519-69815195 E-Mail: [email protected]

Changzhou Smoothies Electronics Co., Ltd. No. 91, Hanjiang West Road, Xinbei District, Changzhou China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 6/6/2020 To whom it may concern: We, Changzhou Smoothies Electronics Co., Ltd. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2ANTI-T18 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, (Signed) Name / Title: MING ZHU /Manager Company: Changzhou Smoothies Electronics Co., Ltd. Address: No. 91, Hanjiang West Road, Xinbei District, Changzhou China Phone: +86-0519-69815194 Fax: +86-0519-69815195 E-Mail: [email protected]

FCC ID:2ANTI-T18 Fig. 1 Fig. 2 Antenna FCC ID:2ANTI-T18 Fig. 3 Fig. 4 FCC ID:2ANTI-T18 Fig. 5 Fig. 6

FCC ID: 2ANTI-T18 Label and Location Label and Location Remote control Model No.: T18 FCC ID: 2ANTI-T18

FCC ID:2ANTI-T18 Fig. 1 Fig. 2 FCC ID:2ANTI-T18 Fig. 3 Fig. 4 FCC ID:2ANTI-T18 Fig. 5 Fig. 6 FCC ID:2ANTI-T18 Fig. 7

This report shall not be reproduced except in full, without the written approval of Shenzhen HUAK Testing Technology Co., Ltd. Page 1 of 2 FCC RF Exposure Evaluation FCC ID: 2ANTI-T18 Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. Conducted Power Results Mode Channel Frequency(MHz) Peak Conducted Output Power (dBm) GFSK 01 2404 0.98 35 2438 0.23 70 2473 -0.20 Manufacturing tolerance GFSK (Peak) Channel Channel 01 Channel 35 Channel 70 Target (dBm) 0.50 0.50 0.50 Tolerance ±(dB) 1.0 1.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen HUAK Testing Technology Co., Ltd. Page 2 of 2 Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power SAR Test Exclusion Threshold SAR Test Exclusion dBm mW GFSK 2.450 5 1.50 2.5119 0.4449 < 3.0 Yes Remark: 1. Output power including tune up tolerance; 2. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. ----------------THE END OF REPORT---------------

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong TEST REPORT Report Reference No. ..................... : FCC ID. ............................................ : GTS20200528002-1-7 2ANTI-T18 Compiled by ( position+printed name+signature) .. : File administrators Jimmy Wang Supervised by ( position+printed name+signature) .. : Test Engineer Aaron Tan Approved by ( position+printed name+signature) .. : Manager Jason Hu Date of issue ..................................... : May.29, 2020 Representative Laboratory Name .: Shenzhen Global Test Service Co.,Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : Changzhou Smoothies Electronics Co., Ltd. Address ............................................ : No. 91, Hanjiang West Road, Xinbei District, Changzhou, China Test specification ...........................: Standard ........................................... : FCC Part 15.247 ANSI C63.10: 2013 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Remote control Trade Mark ....................................... : N/A Manufacturer .................................... : Changzhou Smoothies Electronics Co., Ltd. Model/Type reference....................... : T18 Listed Models .................................. : T18 PRO, T18 PLUS , T18 SE, T18 LITE Modulation Type ............................... : GFSK Operation Frequency ........................ : From 2404MHz to 2473MHz Rating ............................................... : DC 7.40V from battery Result................................................ : PASS Report No.: GTS20200528002-1-7 Page 2 of 34 T E S T R E P O R T Test Report No. : GTS20200528002-1-7 May.29, 2020 __________________________________________3___________________________________________________ Date of issue Equipment under Test : Remote control Model /Type : T18 Listed Models : T18 PRO, T18 PLUS , T18 SE, T18 LITE Applicant : Changzhou Smoothies Electronics Co., Ltd. Address : No. 91, Hanjiang West Road, Xinbei District,Changzhou, China Manufacturer : Changzhou Smoothies Electronics Co., Ltd. Address : No. 91, Hanjiang West Road, Xinbei District,Changzhou, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20200528002-1-7 Page 3 of 34 Contents 1. T E S T S T A N D A R D S ................................................................. 4 2. S U M M A R Y ............................................................................ 5 2.1. General Remarks 5 2.2. Product Description 5 2.3. Equipment Under Test 5 2.4. Short description of the Equipment under Test (EUT) 5 2.5. EUT operation mode 5 2.6. Block Diagram of Test Setup 6 2.7. Related Submittal(s) / Grant (s) 6 2.8. EUT configuration 6 2.9. Modifications 6 3. T E S T E N V I R O N M E N T .............................................................. 7 3.1. Address of the test laboratory 7 3.2. Test Facility 7 3.3. Environmental conditions 7 3.4. Test Description 8 3.5. Statement of the measurement uncertainty 8 3.6. Equipments Used during the Test 9 4. T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 10 4.1. AC Power Conducted Emission ................................................................................... 10 4.2. Radiated Emission ........................................................................................................ 11 4.3. Maximum Peak Output Power ...................................................................................... 17 4.4. Power Spectral Density ................................................................................................ 18 4.5. 6dB Bandwidth ............................................................................................................. 20 4.6. Band Edge Compliance of RF Emission ...................................................................... 22 4.7. Spurious RF Conducted Emission ............................................................................... 25 4.8. Antenna Requirement ................................................................................................... 28 5. T E S T S E T U P P H O T O S O F T H E E U T ......................................... 29 6. E X T E R N A L A N D I N T E R N A L P H O TO S O F T H E E U T ...................... 30 Report No.: GTS20200528002-1-7 Page 4 of 34 1. T E S T S T A N D A R D S The tests were performed according to following standards: The tests were performed according to following standards: ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices ANSI C63.4: 2014: –American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40GHz Range of 9 kHz to 40GHz FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. KDB558074 D01 v05r02: Guidance for Compliance Measurements on Digital Transmis…

Text truncated - open the document above for the full version.

FCC ID:2ANTI-T18 Radiated Emissions