2ANXGT1PROUnder water robot

Geneinno Intelligent Robot T1 Pro Product Name：Under water robot Model Name：T1Pro User Manual V1.0.1 2020.12 Shenzhen Geneinno Technology Co., Ltd www.geneinno.com 2 © 2020-2022GENEINNO All Rights Reserved. 1.Collisionsandburnsoccurrednotcausedbyproductqualityissues; 2.Damagecausedbyunauthorizedmodification,disassembly,andmain shellopening;Anyviolationsoftheofficialinstructionsresultininjury, diseaseorpropertylossoftheuser; 3.Damageorleakingwatercausedbyincorrectinstallation,usageand operationnotfollowingtheusermanualinstructions; 4.Damagecausedbythecustomer'sself-repair,assemblyandinstallations notfollowingofficialinstructions; 5.Damagecausedbyunauthorizedcircuitmodifications,improperuseof batterypacks,non-standardchargers; 6.Anydamagecausedbyimproperdivingactivitiesandunderwaterfilming notfollowingusermanualinstructions; 7.Damagecausedbyapplicationinharshenvironment,suchasinstrong current,againstbigwavesandetc.; 8.Damagecausedbyapplicationsinacomplexelectromagnetic environmentornearstronginterferencesource,suchasminingareas, transmissiontowers,high-voltagelines,transformersubstationsandetc.; 9.Devicemalfunctionscausedbyapplicationswheninterferingwithother wirelessdevices,suchashigh-powertransmitter,imagetransmission device,Wi-Fisignalinterferenceandetc.; 10.Furtherdamagecausedbyusagewhenthepartsareagedordamaged; 11.Damagecausedbyreliabilityandcompatibilityissueswhenusedwith non-certifiedthird-partycomponents; 12.Damagecausedbyinsufficientdischargewhenthebatterycapacityis low,orusingbatterywithqualityissues; 13.Failureordamagecausedbythird-partyproducts,includingproducts providedorembeddedintoT1ProbyGENEINNOatyourrequest; 14.Damagecausedbyunofficialtechnologyorthird-partyguidance,suchas incorrectproductsettings,installation,andfirmwareupgrades; 15.Problemscausedbyoperationsinsensitiveareas(militarybases,nature reserves,marineconservationbasesandetc.); 16.Damagecausedbyforcemajeure,suchasoperationindarkcurrents, cavecollapse,animalhuntingandetc.; 17.Productsorpartswhichlabelsoridentificationcodeshavebeenreplaced ordeliberatelydaubed; 18.Waterdropletsorwatermarksmayappearontheproduct.Thesemaybe causedbytestingafterproduction,andtheywillnotaffecttheuseofthe product. Disclaimer GeneinnoT1Proisalightindustrial-gradeintelligentunderwaterrobot abletodiveto175mdepth.CarriedA17/A7dualcoresCPU,support H264/265ultra-HD4Kvideocodec,built-in12-million-pixelclass professionalcamera,3000lmledfilllightinfront.built-indedicatedimage processingDSP,significantlyimprovethegraphicsprocessingcapabilitiesof variousscenes,meantime,thewholemachineapplyindustrial-grade waterproofsolution.Maxspeedunderwateris2m/s.With2lateralthrusters, 4verticalthrusters,Usingclosed-loopcontrolalgorithm,caneffectively achieve360°fullattitudemotioncontrol,applyfunctionssuchasunderwater hovering,self-balancing,tilting,fixeddepthandorientation,andone-button floating.Hasastronganti-currentabilitytohandlewithcomplex environments.Built-inlarge-capacitylithiumbatteryguaranteeslong operatinghours.GeneinnoT1Proalsosupportsomnidirectionalscanning sonar,waterqualitydetector,laserruler,etc.peripheraldevices,meets requirementsincludingaquaculture,hullinspection,underwatersampling, salvage,rescueandvariousunderwaterexplorationandoperation. I. Introduction 2 © 2020-2022GENEINNO All Rights Reserved. ② ① ② ③ ④ ④ ④ ④ ④ ④ ⑥ ⑦ ⑤ ①Camera②LED light③Signal/ Charging port ④Thruster⑤Extension port⑥Drainage hole ⑦Multifunctional slide (for install balancing weights, manipulators and other accessories) ② ① ① ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ①Wireless relay antenna②Signal/Charging port③Wireless relay connector ④Host connector⑤Battery indicator⑥Connection status indicator ⑦Winding handle⑧Cable windersupport rod⑨Buoyancy cabl ⑩Support chassis 3 1.Please use our product in open water and in an environment with relatively clear water quality. Try to avoid operating in an environment with too many aquatic plants, too turbid, or very complicated underwater structures. 2.Make sure there are no dense radio devices or huge metal objects around the wireless relay and turn on the antenna correctly to avoid affecting the reception of the wireless relay signal. 3.Please use the official standard charger to charge, please charge in time after the battery is alarmed, and do not completely use up. 4.After use, please rinse with fresh water and dry in time to avoid seawater corrosion, and store in a dry and ventilated place. 5.The host is designed with positive buoyancy before installed buoyancy material. It is recommended not to install buoyancy material in fresh water, in seawater can be installed buoyancy material, please adjust the installation position according to the actual balance of the host, subject to the best balance the host can achieve 6.The wireless relay is designed as low-grade waterproof standards, please do not use it directly in water or wash it directly with water. 7.Before using/charging, please check all waterproof connectors if any liquid left such as water, please make it clear before connect. It is recommended to connect the wireless relay first, then connect to the host, the system will boot,when finish using, only needs to disconnect the cable and the host. 8.Please carefully check the motor and propeller make sure it clear before use, do not put your fingers or other body parts into the thruster net cover when the product is working, please clean the surface attachments of the motor and propeller after the machine is off, and wash with fresh water. 9.Aged 16 and below must be under surveillance of adults when use this product, please control the speed while using, avoid excessively fast movement in case scratches or damage equipment. 10.Do not place heavy objects on this product, do not expose it to the sun, and do not store it in a very humid/corrosive environment. 11.Please connect the host and the wireless relay and connect to the APP, follow the instructions to calibrate the compass, and check that the video, data transmission and control are normal, then pu…

Text truncated - open the document above for the full version.

FCC Software Configuration Control Declaration Rev1.1.docx Shenzhen Geneinno Technology Co., Ltd. FCC Software Configuration Control Declaration Date: 2021-05-18 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: Shenzhen Geneinno Technology Co., Ltd. Product Name: Under water robot Model Number(s): T1 Pro,T1,T1 Plus,T1 Pro Plus FCC ID: 2ANXGT1PRO Regarding FCC Country Code Selection guidelines identified in KDB 594280. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Jiankuai Li Date: 2021-05-18 Title: Manager Signatureof applicant

Shenzhen Geneinno Technology Co., Ltd. Agent Authorization Company: Shenzhen Geneinno Technology Co., Ltd. Address: 201-1, Building F3, TCL Science Park, No.1001 Zhongshanyuan Road, Nanshan, Shenzhen, China Product Name: Under water robot Model Number(s): T1 Pro,T1,T1 Plus,T1 Pro Plus Product Description: Under water robot We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-05-18 Name: Jiankuai Li Title: Manager Company: Shenzhen STS Test Services Co., Ltd.

Differences Description We Shenzhen Geneinno Technology Co., Ltd. state: Product： Under water robot Model Name： T1 Pro,T1,T1 Plus,T1 Pro Plus Trade Name: The electrical circuit design, layout, components used and internal wiring for above models are identical, only different in model name. Date: 2021-05-18 Signature Name: Jiankuai Li Title: Manager Company: Shenzhen Geneinno Technology Co., Ltd. Address: 201-1, Building F3, TCL Science Park, No.1001 Zhongshanyuan Road, Nanshan, Shenzhen, China

Shenzhen Geneinno Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021/05/18 Subject; Request for Confidentiality FCC ID: 2ANXGT1PRO To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Jiankuai Li Title: PM

Page 1 of 4 Report No.: STS2103135 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: T1 Pro Photo 1 Photo 2 Page 2 of 4 Report No.: STS2103135 Photo 3 Photo 4 Page 3 of 4 Report No.: STS2103135 Photo 5 Photo 6 Page 4 of 4 Report No.: STS2103135 Photo 7

FCC Label Under water robot Model name: T1 Pro FCC ID: 2ANXGT1PRO This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 1 of 4 Report No.: STS2103135 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: T1 Pro Photo 1 Photo 2 Photo 3 Antenna Page 2 of 4 Report No.: STS2103135 Photo 4 Page 3 of 4 Report No.: STS2103135 Photo 5 Photo 6 Page 4 of 4 Report No.: STS2103135 Photo 7 Photo 8

RF Exposure Report FCC ID: 2ANXGT1PRO RF Exposure Measurement The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) F= Frequency in MHz Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. EUT Operation condition EUT was enabled to transmit and receive at lowest, middle and highest channels. Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. 2.4G WIFI Mode 802.11b/g/n20:2412-2462MHz 802.11n40:2422-2452MHz Detector Peak 802.11b 24±1dBm 802.11g 24±1dBm 802.11n20 25±1dBm 802.11n40 24±1dBm ANT Gain (G) Antenna number: 1 Antenna A gain : 3dBi (gain of antenna in linear scale=1.995) EUT does not support simultaneous transmission of 2.4G WIFI and 5G WIFI Protocol ANT Gain(gain of antenna in linear scale) Channel Frequency (MHz) Output Power to Antenna (dBm) Output Power to Antenna (mW) Power Density (mW/cm²) Limit (mW/cm²) 802.11 b 1.995 2412 24.69 294.4422 0.1168617 1 802.11 g 1.995 2412 25.85 384.5918 0.1526413 1 802.11 n20 1.995 2412 25.91 389.942 0.1547647 1 802.11 n40 1.995 2452 25.08 322.1069 0.1278416 1 5.8G WIFI Mode 802.11a/n20/n40/ac20/ac40/ac80: 5.525-5.85GHz Detector AV 802.11a 8.82dBm; 802.11n20 (mimo) 11±1dBm 802.11 n40 (mimo) 11±1dBm 802.11ac20 (mimo) 11±1dBm 802.11ac40 (mimo) 11±1dBm 802.11ac80 (mimo) 11±1dBm ANT Gain (G) Antenna number: 2 Antenna A gain : 3dBi Antenna B gain : 3dBi (gain of antenna in linear scale=1.9952) MIMO technology Directional gain= 6.01dBi (gain of antenna in linear scale=3.9902) Protocol ANT Gain(gain of antenna in linear scale) Channel Frequency (MHz) Output Power to Antenna (dBm) Output Power to Antenna (mW) Power Density (mW/cm²) Limit (mW/cm²) 802.11 a 1.9952 5745 8.82 7.62079 0.0030249 1 802.11 n20 3.9902 5785 11.216 13.23122 0.0105033 1 802.11 n40 3.9902 5755 11.294 13.47101 0.0106936 1 802.11 ac20 3.9902 5745 11.19 13.15225 0.0104406 1 802.11 ac40 3.9902 5795 11.167 13.08278 0.0103854 1 802.11 ac80 3.9902 5775 11.186 13.14014 0.0104309 1

Page 1 of 6 Report No.: STS2103135W04 Power Spectrum Density-Ant A WLAN_Band-4 WLAN_Band-4 W58_11a20_Lower_Power Spectrum Density W58_11a20_Middle_Power Spectrum Density W58_11a20_Higher_Power Spectrum Density W58_11n20_Lower_Power Spectrum Density W58_11n20_Middle_Power Spectrum Density W58_11n20_Higher_Power Spectrum Density Page 2 of 6 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11n40_Lower_Power Spectrum Density W58_11n40_Higher_Power Spectrum Density W58_11ac20_Lower_Power Spectrum Density W58_11ac20_Middle_Power Spectrum Density W58_11ac20_Higher_Power Spectrum Density W58_11ac40_Lower_Power Spectrum Density Page 3 of 6 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11ac40_Higher_Power Spectrum Density W58_11ac80_Power Density_5775M Page 4 of 6 Report No.: STS2103135W04 Power Spectrum Density-Ant B WLAN_Band-4 WLAN_Band-4 W58_11a20_Lower_Power Spectrum Density W58_11a20_Middle_Power Spectrum Density W58_11a20_Higher_Power Spectrum Density W58_11n20_Lower_Power Spectrum Density W58_11n20_Middle_Power Spectrum Density W58_11n20_Higher_Power Spectrum Density Page 5 of 6 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11n40_Lower_Power Spectrum Density W58_11n40_Higher_Power Spectrum Density W58_11ac20_Lower_Power Spectrum Density W58_11ac20_Middle_Power Spectrum Density W58_11ac20_Higher_Power Spectrum Density W58_11ac40_Lower_Power Spectrum Density Page 6 of 6 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11ac40_Higher_Power Spectrum Density W58_11ac80_Power Density_5775M

Page 1 of 3 Report No.: STS2103135W04 26BW and 99% WLAN_Band-4 WLAN_Band-4 W58_11a20_Lower_26BW and 99% W58_11a20_Middle_26BW and 99% W58_11a20_Higher_26BW and 99% W58_11n20_Lower_26BW and 99% W58_11n20_Middle_26BW and 99% W58_11n20_Higher_26BW and 99% Page 2 of 3 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11n40_Lower_26BW and 99% W58_11n40_Higher_26BW and 99% W58_11ac20_Lower_26BW and 99% W58_11ac20_Middle_26BW and 99% W58_11ac20_Higher_26BW and 99% W58_11ac40_Lower_26BW and 99% Page 3 of 3 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11ac40_Higher_26BW and 99% W58_11ac80_26BW_99%_Bandwidth_5775M

Page 1 of 3 Report No.: STS2103135W04 6BW WLAN_Band-4 WLAN_Band-4 W58_11a20_Lower_6BW W58_11a20_Middle_6BW W58_11a20_Higher_6BW W58_11n20_Lower_6BW W58_11n20_Middle_6BW W58_11n20_Higher_6BW Page 2 of 3 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11n40_Lower_6BW W58_11n40_Higher_6BW W58_11ac20_Lower_6BW W58_11ac20_Middle_6BW W58_11ac20_Higher_6BW W58_11ac40_Lower_6BW Page 3 of 3 Report No.: STS2103135W04 WLAN_Band-4 WLAN_Band-4 W58_11ac40_Higher_6BW W58_11ac80_-6_Bandwidth_5775M

Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, all test data presented in this report is only applicable to presented test sample. Shenzhen STS Test Services Co., Ltd. A 1/F, Building B, Zhuoke Science Park, No.190 Chongqing Road, HepingShequ, Fuyong Sub-District, Bao’an District, Shenzhen, Guang Dong, China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:[email protected] RADIO TEST REPORT Report No.:STS2103135W04 Issued for Shenzhen Geneinno Technology Co., Ltd. 201-1, Building F3, TCL Science Park, No.1001 Zhongshanyuan Road, Nanshan, Shenzhen, China Product Name: Under water robot Brand Name: Model Name: T1 Pro Series Model: T1,T1 Plus,T1 Pro Plus FCC ID: 2ANXGT1PRO Test Standard: FCC Part 15.407 S T L A B S Page 2 of 49 Report No.: STS2103135W04 TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Geneinno Technology Co., Ltd. Address ................................. : 201-1, Building F3, TCL Science Park, No.1001 Zhongshanyuan Road, Nanshan, Shenzhen, China Manufacturer's Name .......... : Shenzhen Geneinno Technology Co., Ltd. Address ................................. : 201-1, Building F3, TCL Science Park, No.1001 Zhongshanyuan Road, Nanshan, Shenzhen, China Product Description Product Name ........................ : Under water robot Brand Name ......................... : Model Name .......................... : T1 Pro Series Model .......................... : T1,T1 Plus,T1 Pro Plus Test Standards ..................... : FCC Part15.407 Test Procedure............................... : ANSI C63.10-2013 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, this document only be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of Test ............................................ : Date of receipt of test item ...................... : 22 Mar. 2021 Date (s) of performance of tests ............. : 22 Mar. 2021 ~ 27 Apr. 2021 Date of Issue ........................................... : 27 Apr. 2021 Test Result ............................................... : Pass Testing Engineer : (Chris Chen) Technical Manager : (Sean she) Authorized Signatory : (Vita Li) Page 3 of 49 Report No.: STS2103135W04 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2 . GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF TEST MODES 10 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 12 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 13 3 . EMC EMISSION TEST 15 3.1 CONDUCTED EMISSION MEASUREMENT 15 3.2 RADIATED EMISSION AND ( BANDEDGE) MEASUREMENT 19 4. POWER SPECTRAL DENSITY TEST 34 4.1 LIMIT 34 4.2 TEST PROCEDURE 34 4.3 DEVIATION FROM STANDARD 35 4.4 TEST SETUP 35 4.5 EUT OPERATION CONDITIONS 35 4.6 TEST RESULTS 36 5. BANDWIDTH MEASUREMENT 37 5.1 EMISSION BANDWIDTH (EBW) 26 BANDWID PROCEDURES / LIMIT 37 5.2 OCCUPIED BANDWIDTH ( 99%) TEST APPLIED PROCEDURES / LIMIT 39 5.3 MINIMUM EMISSION BANDWIDTH(6 DB) PROCEDURES / LIMIT 41 6. MAXIMUM CONDUCTED OUTPUT POWER 43 6.1 LIMIT 43 6.2 TEST PROCEDURE 43 6.3 DEVIATION FROM STANDARD 43 6.4 TEST SETUP 43 6.5 EUT OPERATION CONDITIONS 43 6.6 TEST RESULTS 44 7. AUTOMATICALLY DISCONTINUE TRANSMISSION 47 7.1 LIMIT OF AUTOMATICALLY DISCONTINUE TRANSMISSION 47 7.2 TEST RESULT OF AUTOMATICALLY DISCONTINUE TRANSMISSION 47 Page 4 of 49 Report No.: STS2103135W04 Table of Contents Page 8. ANTENNA REQUIREMENT 48 8.1 STANDARD REQUIREMENT 48 8.2 EUT ANTENNA 48 APPENDIX - PHOTOS OF TEST SETUP 49 Page 5 of 49 Report No.: STS2103135W04 Revision History Rev. Issue Date Report NO. Effect Page Contents 00 27 Apr. 2021 STS2103135W04 ALL Initial Issue Page 6 of 49 Report No.: STS2103135W04 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: § 15.407,KDB 789033 D02 General U-NII Test Procedures New Rules v02r01 FCC Part 15.407 FCC standard Test Item Results 15.207 AC Conducted Emission PASS 15.407 (a) /15.407 (e) 26dB/6dB &99% Bandwidth PASS 15.407(a) Maximum Conducted Output Power PASS 15.407(b)/15.205/15.209 Radiated Emission And (bandedge Emissions) Measurement PASS 15.407(a) Power Spectral Density PASS 15.407(c) Automatically Discontinue Transmission PASS 15.203/15.204 Antenna Requirement PASS NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2013. Page 7 of 49 Report No.: STS2103135W04 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : A 1/F, Building B, Zhuoke Science Park, No.190 Chongqing Road, HepingShequ, Fuyong Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.68dB 2 Unwanted Emissions, conducted ±2.988dB 3 All emissions, radiated 9K-30MHz ±2.84dB 4 All emissions, radiated 30M-1GHz ±4.39dB 5 All emissions, radiated 1G-6GHz ±5.10dB 6 All emissions, radiated>6G ±5.48dB 7 Conducted Emission (9KHz-150KHz) ±2.79dB 8 Conducted Emission (150KHz-30MHz) ±2.80dB Page 8 of 49 Report No.: STS2103135W04 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Under water robot Trade Name Model Name T1 Pro Series Model T1,T1 Plus,T1 Pro Plus Model Difference Only different in model name. Produc…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2ANXGT1 Pro DTS&U-NII Setup photo Model name: T1 Pro DTS&U-NII conduction DTS&U-NII radiation L Page 2 of 2 FCC ID: 2ANXGT1 Pro DTS&U-NII radiation H