2AOI7-CRV-500CNightwave

SERIES CAMERAS TM USER MANUAL SIONYX, LLC NIGHTWAVE Made in Taiwan SIONYX.com/patents NEED HELP? ONLINE CHAT SUBMIT A TICKET 24/7 SUPPORT CALL www.sionyx.com www.sionyx.com/contact www.support.sionyx.com (866) 827-8237 Register your device and stay up to date by visiting the URL or scanning the QR code below. SIONYX, LLC Cummings Center Beverly, MA 01915 U.S.A. (978) 922-0684 [email protected] FOLLOW US Share your SIONYX content and be sure to tag us! 01TABLE OF CONTENTS WELCOME TO NIGHTWAVE GETTING STARTED INSTALLATION GETTING CONNECTED CAMERA SETUP SAFETY MAINTENANCE ADDITIONAL RESOURCES 02 03 05 14 17 18 27 28 TABLE OF CONTENTS 02SIONYX NIGHTWAVE USER MANUAL WELCOME TO NIGHTWAVE NIGHTWAVE CAMERA ANALOG VIDEO CAMERA USB CABLE ALLEN WRENCH IN-LINE FUSE USB CABLE BOX INCLUDES: THIS IS SIONYX. We believe that human endeavor should not be limited by daylight. In the darkness of night, greatness is possible. Adventure enabled. And a full sense of all sight achievable, no matter the light. SMA TO BNC ADAPTER BNC TO RCA ADAPTER BASE GASKET MOUNTING SCREWS TEMPLATE 03GETTING STARTED To get started, please review the legends on the following pages. GETTING STARTED GETTING STARTED 04SIONYX NIGHTWAVE USER MANUAL 05INSTALLATION INSTALLATION When planning the installation location, consider the following points: • The camera is waterproof, and appropriate for above decks mounting. • When mounting the camera in a ball-down position, ensure that the camera is installed with adequate drainage so that standing water does not collect in the base. • Ensure the camera is installed in a location that will allow it to be accessed for regular periodic cleaning (fresh-water rinse), inspection of mounting point integrity and mechanical soundness, and preventative maintenance. • The underside (inside) of the compartment or deck on to which the camera is mounted must be weather-tight. You must ensure protection from water ingress to cables and connections. • The mounting surface must be horizontal. • Fixings are supplied for a mounting surface up to X mm (X in) thick. A thicker surface will require the installer to provide alternative fixings. • The camera should be mounted as high as practical, but without interfering with any radar, navigational or communications electronics. • Choose a location that will provide the most unobstructed view in all directions. • Select a location for the camera that is at least X m (X in.) from any magnetic compass. • Select a location that is at least X m (X ft) from devices that may cause interference, such as motors, generators and radio transmitters / receivers. CAMERA MOUNTING: LOCATION 06SIONYX NIGHTWAVE USER MANUAL Plan your system. Obtain all required equipment and tools. Site all equipment. Route all cables. Drill cable and mounting holes. Make all connections into equipment. Secure all equipment in place. Power on and test the system. Installation includes the following activities: INSTALLATION CHECKLIST INSTALLATION 07INSTALLATION MOUNTING THE CAMERA Use these instructions to mount the camera unit in position. Using the template supplied, mark and drill the holes for mounting the camera. Mounting the Camera: Bottom Up PLACEHOLDER: BOTTOM UP 08SIONYX NIGHTWAVE USER MANUAL Mounting the Camera: Top Down PLACEHOLDER: TOP DOWN 09INSTALLATION PLACEHOLDER: TRIPOD 10SIONYX NIGHTWAVE USER MANUAL CAMERA ORIENTATION The camera can be mounted in 2 orientations known as “Ball up” and “Ball down.” The default video image orientation is for the ball-up configuration; if the camera is to be mounted in the ball-down configuration then the video image must be rotated. BALL-UP: The camera is mounted on top of the mounting surface. BALL-DOWN: The camera is suspended upside down, below the mounting surface. 11INSTALLATION GENERAL CABLING GUIDANCE Cable Types and Length • It is important to use cables of the appropriate type and length. • Unless otherwise stated, only use cables supplied by SIONYX. • Ensure that any non-SIONYX cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing Cables Cables must be routed correctly, to maximize performance and prolong cable life. • Do NOT bend cables excessively. Wherever possible, ensure a minimum bend diameter of 200 mm (8 in) / minimum bend radius of 100 mm (4 in). • Protect all cables from physical damage and exposure to heat. Use trunking or conduit where possible. Do NOT run cables through bilges or doorways, or close to moving or hot objects. • Secure cables in place using tie-wraps or lacing twine. Coil any extra cable and tie it out of the way. • Where a cable passes through an exposed bulkhead or deckhead, use a suitable watertight feed- through. • Do NOT run cables near engines or fluorescent lights. • Always route data cables as far away as possible from other equipment and cables, high current carrying AC and DC power lines, and antennas. 12SIONYX NIGHTWAVE USER MANUAL Strain Relief Ensure adequate strain relief is provided. Protect connectors from strain and ensure they will not pull out under extreme sea conditions. Circuit Isolation Appropriate circuit isolation is required for installations using both AC and DC current: • Always use isolating transformers or a separate power-inverter to run PC’s, processors,displays and other sensitive electronic instruments or devices. • Always use an isolating transformer with Weather FAX audio cables. • Always use an isolated power supply when using a 3rd party audio amplifier. • Always use an RS232/NMEA converter with optical isolation on the signal lines. • Always make sure that PC’s or other sensitive electronic devices have a dedicated power circuit. 13INSTALLATION VERSATILE MOUNTING INSTALLATION LOCATION REQUIREMENTS When planning the installation location, consider the following points: • The camera is water-resistant, and appropriate for above decks mounting. • When mounting the camera i…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 1 / 12 Rev. 01 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 2 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 3 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 4 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 5 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 6 / 12 Rev. 01

Rating Label (on the Camera) Size: 57.34(L) x 25.92(W) mm (T: 0.15mm) Material: White PET Paper + PP Coating 白色特多龍上霧膜 Printing Color: Black 黑色 需SN流水號條碼 Sionyx CRV-500C 2022.05.18V02 CRV5YYMMRRRRR Serieal Number EX:CRV5220500001 25.92 mm 57.34 mm 088-LS0087-00 Product Label ,A1 Nightwave Model : CRV-500C Made in Taiwan FCC ID: 2AOI7-CRV-500C IC: 23556-CRV500C USB: 5VDC 1A 0.5A NTSC: 12VDC SN:CRV5220500001 MAC:XXXXXXXXXXXX XXXXXXXXXXXXXX MAC Number EX:CRV5220500001 Removable label FCC Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference and (2)this device must accept any interference received, including interference that may cause undesired operation

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 7 / 12 Rev. 01 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 8 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 9 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 10 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 11 / 12 Rev. 01 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No.: TM-2204000360P Page 12 / 12 Rev. 01 Antenna

Project No.: TM-2204000360P FCC ID: 2AOI7-CRV-500C Page: 1 / 13 Report No.: TMWK2204001418KR Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RF Exposure Evaluation Report FCC 47 CFR § 2.1091 for Nightwave Model Name.: CRV-500C Prepared for: SiOnyx, LLC 100 Cummings Center, Suite 303B, Beverly, MA 01915, USA Prepared by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issue Date: July 1, 2022 Note: This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, NIST or any government agencies. The test results in the report only apply to the tested sample. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 13 Report No.: TMWK2204001418KR Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 24, 2022 Initial Issue ALL Allison Chen 01 July 1, 2022 See the following Note Rev.(01) P.1, 4, 10-12 Allison Chen Note: Rev.(01) 1. Added mpe exemption standard in section 4.3, 4.4, and test data in section 5 2. Modified applicant information. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 13 Report No.: TMWK2204001418KR Rev.: 01 Table of Contents 1 ATTESTATION OF TEST RESULTS ................................................................... 4 2 TEST SPECIFICATION, METHODS AND PROCEDURES ................................. 5 3 DEVICE UNDER TEST (DUT) INFORMATION .................................................... 6 3.1 DUT DESCRIPTION .............................................................................................................. 6 3.2 WIRELESS TECHNOLOGIES ............................................................................................... 7 4 MAXIMUM PERMISSIBLE EXPOSURE .............................................................. 8 4.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ............................................... 8 4.2 MPE CALCULATION METHOD ............................................................................................. 9 4.3 MPE EXEMPTION ............................................................................................................... 10 4.4 MULTIPLE RF SOURCES ................................................................................................... 11 5 RADIO FREQUENCY RADIATION MAX EXPOSURE EVALUATION .............. 12 6 FACILITIES ........................................................................................................ 13 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 13 Report No.: TMWK2204001418KR Rev.: 01 1 Attestation of Test Results Applicant Name SiOnyx, LLC Model Name CRV-500C Applicable Standards FCC 47 CFR § 2.1091 KDB 447498 D04 FCC 47 CFR § 1.1307 FCC 47 CFR § 1.1310 Published RF exposure KDB procedures Receive EUT Date: April 20, 2022 Compliance Certification Services Inc. , tested the above equipment in accordance with the requirements set forth in the above standards. Determination of compliance is based on the results of the compliance measurement,not taking into account measurement instrumentation uncertainy.All indications of Pass/Fail in this report are opinions expressed by Compliance Certification Services Inc, based on interpretations and/or observations of test results. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved & Released By: Sky Zhou Asst. Section Manager Compliance Certification Services Inc. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 5 / 13 Report No.: TMWK2204001418KR Rev.: 01 2 Test Specification, Methods and Procedures The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1091, the following FCC Published RF exposure KDB procedures: o 447498 D04 Interim General RF Exposure Guidance v01 o 865664 D02 RF Exposure Reporting v01r02 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 6 / 13 Report No.: TMWK2204001418KR Rev.: 01 3 Device Under…

Text truncated - open the document above for the full version.

Project No.: TM-2204000360P FCC ID: 2AOI7-CRV-500C Page: 1 / 80 Report No.: TMWK2204001416KR IC: 23556-CRV500C Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-247 Test Standard FCC Part 15.247 RSS-247 issue 2 and RSS-GEN issue 5 Product name Nightwave Brand Name SiOnyx Model No. CRV-500C Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory). Approved by: Sehni Hu Supervisor This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 80 Report No.: TMWK2204001416KR Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 24, 2022 Initial Issue ALL Allison Chen 01 July 1, 2022 See the following Note Rev.(01) P.4, 12 Allison Chen Note: Rev.(01) 1. Modified applicant address, worst mode. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 80 Report No.: TMWK2204001416KR Rev.: 01 Table of contents 1. GENERAL INFORMATION ............................................................................................... 4 1.1 EUT INFORMATION ......................................................................................................... 4 1.2 EUT CHANNEL INFORMATION ....................................................................................... 5 1.3 ANTENNA INFORMATION ............................................................................................... 5 1.4 MEASUREMENT UNCERTAINTY .................................................................................... 6 1.5 FACILITIES AND TEST LOCATION................................................................................. 7 1.6 INSTRUMENT CALIBRATION ......................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ....................................................... 9 1.8 TEST METHODOLOGY AND APPLIED STANDARDS .................................................... 9 2. TEST SUMMARY............................................................................................................ 10 3. DESCRIPTION OF TEST MODES .................................................................................. 11 3.1 THE WORST MODE OF OPERATING CONDITION ...................................................... 11 3.2 THE WORST MODE OF MEASUREMENT..................................................................... 12 3.3 EUT DUTY CYCLE ......................................................................................................... 13 4. TEST RESULT ................................................................................................................ 14 4.1 AC POWER LINE CONDUCTED EMISSION .................................................................. 14 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ............................................. 17 4.3 OUTPUT POWER MEASUREMENT .............................................................................. 25 4.4 POWER SPECTRAL DENSITY ...................................................................................... 29 4.5 CONDUCTED BANDEDGE AND SPURIOUS EMISSION .............................................. 34 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION ................................................. 44 APPENDIX 1 - PHOTOGRAPHS OF EUT .............................................................................. A-1 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 80 Report No.: TMWK2204001416KR Rev.: 01 1. GENERAL INFORMATION 1.1 EUT INFORMATION FCC Applicant / Manufacturer SiOnyx, LLC 100 Cummings Center, Suite 303B, Beverly, MA 01915, USA IC Applicant / Manufacturer SiOnyx, LLC 100 Cummings Centre, Suite 303B, Beverly, MA …

Text truncated - open the document above for the full version.

Project No.: TM-2204000360P FCC ID: 2AOI7-CRV-500C Page: 1 / 47 Report No.: TMWK2204001417KR IC: 23556-CRV500C Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-247 Test Standard FCC Part 15.247 RSS-247 issue 2 and RSS-GEN issue 5 Product name Nightwave Brand Name SiOnyx Model No. CRV-500C Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory) Approved by: Sehni Hu Supervisor This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 2 / 47 Report No.: TMWK2204001417KR Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 24, 2022 Initial Issue ALL Allison Chen 01 July 1, 2022 See the following Note Rev.(01) P.4, 12 Allison Chen Note: Rev.(01) 1. Modified applicant address, worst mode. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 3 / 47 Report No.: TMWK2204001417KR Rev.: 01 Table of contents 1. GENERAL INFORMATION ........................................................................................ 4 1.1 EUT INFORMATION .................................................................................................. 4 1.2 EUT CHANNEL INFORMATION ................................................................................ 5 1.3 ANTENNA INFORMATION ........................................................................................ 5 1.4 MEASUREMENT UNCERTAINTY .............................................................................. 6 1.5 FACILITIES AND TEST LOCATION .......................................................................... 7 1.6 INSTRUMENT CALIBRATION ................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ................................................. 9 1.8 TEST METHODOLOGY AND APPLIED STANDARDS ............................................. 9 2. TEST SUMMARY ..................................................................................................... 10 3. DESCRIPTION OF TEST MODES............................................................................ 11 3.1 THE WORST MODE OF OPERATING CONDITION ................................................ 11 3.2 THE WORST MODE OF MEASUREMENT .............................................................. 12 3.3 EUT DUTY CYCLE ................................................................................................... 13 4. TEST RESULT ......................................................................................................... 14 4.1 AC POWER LINE CONDUCTED EMISSION ........................................................... 14 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ...................................... 17 4.3 OUTPUT POWER MEASUREMENT ........................................................................ 21 4.4 POWER SPECTRAL DENSITY ................................................................................ 24 4.5 CONDUCTED BAND EDGE AND SPURIOUS EMISSION ...................................... 27 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION .......................................... 31 APPENDIX 1 - PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: 4 / 47 Report No.: TMWK2204001417KR Rev.: 01 1. GENERAL INFORMATION 1.1 EUT INFORMATION FCC Applicant / Manufacturer SiOnyx, LLC 100 Cummings Center, Suite 303B, Beverly, MA 01915, USA IC Applicant / Manufacturer SiOnyx, LLC 100 Cummings Centre, Suite 303B, Beverly, MA 01915, United States Of America (Excluding The State Of Alaska) Equipment Nightwave Model Name CRV-500C Model Discrepancy N/A Brand Name SiOnyx Received Date April 20, 2022 Date of Test April 25~26, 2022 Power Supply Powe…

Text truncated - open the document above for the full version.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-4 Report No.: TMWK2204001416KR Rev.: 01 APPENDIX-A Test Photo Radiation (Below 1GHz) Radiation (Above 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-4 Report No.: TMWK2204001416KR Rev.: 01 Conducted Emission Set Up Photo This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-3 / A-4 Report No.: TMWK2204001416KR Rev.: 01 Conduction This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-4 / A-4 Report No.: TMWK2204001416KR Rev.: 01

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-1 / A-4 Report No.: TMWK2204001417KR Rev.: 01 APPENDIX-A Test Photo Radiation (Below 1GHz) Radiation (Above 1GHz) This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-2 / A-4 Report No.: TMWK2204001417KR Rev.: 01 Conducted Emission Set up Photo This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-3 / A-4 Report No.: TMWK2204001417KR Rev.: 01 Conduction This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page: A-4 / A-4 Report No.: TMWK2204001417KR Rev.: 01