2AOKB-T8420SFloodlight Camera

Anker Innovations Limited. All rights reserved. Eufy Security and Eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005002595 V01 Quick Start Guide Floodlight Camera Table of Contents Safety Instructions 01 What's in the Box 01 Getting Started 02 Installing the Junction Box 04 Mounting Floodlight Camera 07 Adjusting Floodlight Camera 09 Restoring Power 10 Using the Floodlight Camera on the Eufy Security App 10 NOTICE 12 01 ENEN 02 Getting Started 1 . Shut the power off at the breaker in your house. Switch on/off the lights to make sure the electricity in your house is properly shut off. 2 . Determine the area you want to be lit and camera coverage is required. Install your Floodlight Camera on the front wall or on a side wall of your house. To get optimal detection and light coverage for the floodlight and camera, install it on a side wall if possible. * * The motion sensor is more sensitive to movements across the camera field of view than movements towards or away from the sensor. We highly recommend you install the floodlight camera on the side wall. Safety Instructions 1 . Shut off power at the fuse or circuit breaker before installing. 2 . Do not install the device near flammable surfaces. 3 . Must have a licensed electrician install the Floodlight Camera. 4 . Do not use the device in environments where the temperature is too high or too low, avoid exposing the device to direct sunshine or very wet environments. 5 . The suitable temperature for the product and accessories is -20°C to 50°C. What's in the Box Floodlight Camera (T8420S) Junction Box Central Screw CapPlate Screws Installation Hook Central Screw 03 ENEN 04 On the side wall: Move towards or leave vertically Move horizontally Increased detection range for vertical movement up to 26ft (8m) Increased detection range for horizontal movement up to 33ft (10m) On the front wall: Move towards or leave vertically Move horizontally Detection range for vertical movement up to 20ft (6m) Detection range for horizontal movement up to 26ft (8m) Installing the Junction Box 1 . Remove the rubber plugs indicated in the illustration below. 2 . Run the existing wire through the hole. If you don’t have existing wires outdoors, contact a licensed electrician to run the wires. 05 ENEN 06 4 . Unscrew the bolt with a flat-head screwdriver. Connect the Neutral (blue) / Ground (green / green and yellow) / Live (brown) wire to the Neutral / Ground / Live wire connector in the junction box respectively. Secure the wires tightly to prevent wires from falling. N L Neutral Ground Live 12 3 . Install the junction box: • Orientate the two mounting holes vertically to ensure stable mounting. • On wooden walls, DO NOT pre-drill holes. Use the screws provided to fix the junction box onto the wall. • On walls that are made out of hard materials, such as stucco, brick, or concrete, drill holes with a 15/64 inch (6 mm) drill bit, and then insert the anchors provided into the holes. Use the screws provided to fix the junction box on the wall. 12 07 ENEN 08 Connect Wires 1 . Connect Ground wire from the Floodlight Camera to the Ground wire from the wire connector in the junction box. 2 . Connect the Live / Neutral wire from the Floodlight Camera to the Live / Neutral wire from the wire connector in the junction box respectively. 3 . Secure the wires with a flat-head screwdriver. Green / green and yellow, brown and blue wires must connect to the matching colors. Never cross connect. Mounting Floodlight Camera Hang Floodlight Camera Hang Floodlight Camera on the junction box with the hook provided. 09 ENEN 10 Restoring Power Switch on the main circuit breaker in the house. To confirm whether the Floodlight Camera is operating, check the LED indicator. If it is flashing red, it is ready for Eufy Security App setup. If Floodlight Camera is not powered on, switch off the circuit breaker before checking the wiring of Floodlight Camera. Using the Floodlight Camera on the Eufy Security App 1 . Download the Eufy Security app from the App Store (iOS devices) or Google Play (Android devices). 2 . Sign up for a Eufy Security account. Follow the onscreen instructions to connect Floodlight Camera to your Wi-Fi network. Now you can check live stream in the Eufy Security App. The Floodlight Camera can be used only after your phone and the Floodlight Camera are connected to the same wireless network. Mount Floodlight Camera On the Junction Box 1 . Align the hole on the junction box with the opening in the Floodlight Camera. 2 . Screw the central screw through the center of Floodlight Camera to mount it in position. 3 . Cover the central screw with the central screw cap to prevent it from rusting. Adjusting Floodlight Camera 1 . After installation is complete, loosen the adjustment screws on the camera and floodlight to adjust the camera and light position to the desired angles. 2 . Tighten the screws firmly to complete the installation. 11 ENEN 12 For troubleshooting, check the Help section in the Eufy Security app. Refer to the app for information on the various LED status indications. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party ： Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541 Telephone:1-800-988-7973 This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provis…

Text truncated - open the document above for the full version.

FCCID:2AOKB-T8420S

FCCID:2AOKB-T8420S BLE&WiFiANT

AnkerInnovationsLimited DeclarationconcerningAntennaSpecification Itisherebydeclaredthattheproduct ModelNo.:T8420S FCCID:2AOKB-T8420S fulfillstherequirementinFCCtestrelatingtotheantennatype. ThedevicespecifiedaboveconfirmstotheFCCrecommendationsforinternalantennatype(s) describedbelow: ModelNo.ofantenna:N/A Typeofantenna:PIFAantenna Gainoftheantenna:2.6dBi Frequencyrange:BLE:2402~2480MHz WIFI2.4G:2412MHz~2462MHz Themountingoftheantennaisfixedtotheradiomoduleandnootherantennashouldbeused. Companyname:AnkerInnovationsLimited Address:Room1318-19,HollywoodPlaza,610NathanRoad,Mongkok,Kowloon, HongKong City:Kowloon ZIP/Postalcode:N/A Country:HongKong Place:KowloonDate:2021-07-27 Signature: version01

RFEXPOSUREEVALUATION AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeusedtoevaluatethe environmentimpactofhumanexposuretoradiofrequency(RF)Radiationasspecifiedin §1.1307(b) FCCID:2AOKB-T8420S EUTSpecification EUTFloodlightCamera Frequencyband(Operating)WLAN:2.412GHz~2.462GHz WLAN:5.18GHz~5.24GHz WLAN:5.745GHz~5.825GHz Others:2.402GHz~2.480GHz DevicecategoryPortable(<20cmseparation) Mobile(>20cmseparation) Others___ ExposureclassificationOccupational/Controlledexposure(S=5mW/cm2) GeneralPopulation/Uncontrolledexposure(S=1mW/cm2) AntennadiversitySingleantenna Multipleantennas Txdiversity Rxdiversity Tx/Rxdiversity Max.outputpowerWIFI2.4G:23.25dBm(0.2113W);BLE:10.04dBm(0.0101W) Antennagain(Max)BLE:2.6dBi WiFi2.4G:2.6dBi EvaluationappliedMPEEvaluation SAREvaluation LimitsforMaximumPermissibleExposure(MPE) Frequency Range(MHz) ElectricField Strength(V/m) MagneticField Strength(A/m) Power Density(mW/cm 2 ) Average Time (A)LimitsforOccupational/ControlExposures 300-1500----F/3006 1500-100000----56 (B)LimitsforGeneralPopulation/UncontrolExposures 300-1500----F/15006 1500-100000----130 Friistransmissionformula:Pd=(Pout*G)\(4*pi*R2) Where Pd=PowerdensityinmW/cm 2 Pout=outputpowertoantennainMw G=gainofantennainlinearscale Pi=3.1416 R=distancebetweenobservationpointandcenteroftheradiatorincm PdthelimitofMPE,1mW/cm2.Ifweknowthemaximumgainoftheantennaandtotalpower inputtotheantenna,throughthecalculation,wewillknowthedistancewheretheMPElimitis reached. MaxMeasurementResult(Worstcase) Operating Mode Measured Power Tuneup tolerance Max.Tune upPower Antenna Gain Powerdensity at20cm Powerdensity Limits (mW/cm2) (dBm)(dBm)(dBm)(dBi)(mW/cm2) WiFi2.4G23.2523.25±124.252.60.09641 BLE10.0410.04±111.042.60.00461

Page 1 of 22 AppendixTestData ReportNo.:18220WC10106001TestDate:2021.7.7 TestEngineer:Auditor: Temperature:24.3°CRelativeHumidity:56% Pressure:1012hPa 1.DutyCycle 1.1Ant1 1.1.1TestResult Ant1 Mode TX Type Frequency (MHz) T_on(ms)Period(ms)DutyCycle(%) DutyCycleCorrectionFactor (dB) Max.DCVariation (%) 1MSISO 24020.070.6211.209.510.03 24400.090.6215.048.230.00 24800.090.6215.048.230.00 Page 2 of 22 1.1.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 3 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 4 of 22 2.Bandwidth 2.1OBW 2.1.1TestResult ModeTXTypeFrequency(MHz)Ant99%OccupiedBandwidth(MHz)LimitVerdict 1MSISO 240211.05/Pass 244011.05/Pass 248011.05/Pass Page 5 of 22 2.1.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 6 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 7 of 22 2.26dBBW 2.2.1TestResult ModeTXTypeFrequency(MHz)Ant6dBBandwidth(MHz)LimitVerdict 1MSISO 240210.66>=0.5Pass 244010.66>=0.5Pass 248010.66>=0.5Pass Page 8 of 22 2.2.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 9 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 10 of 22 3.MaximumConductedOutputPower 3.1Power 3.1.1TestResult ModeTXTypeFrequency(MHz) MeasuredPeakOutputPower(dBm) Verdict Ant1Limit 1MSISO 24029.72<=30Pass 24409.93<=30Pass 248010.04<=30Pass Note1:AntennaGain:Ant1:2.60dBi; Page 11 of 22 3.1.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 12 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 13 of 22 4.MaximumPowerSpectralDensity 4.1PSD 4.1.1TestResult ModeTXTypeFrequency(MHz) MaximumPSD(dBm/3kHz) Verdict Ant1Limit 1MSISO 2402-5.70<=8Pass 2440-5.57<=8Pass 2480-5.80<=8Pass Note1:AntennaGain:Ant1:2.60dBi; Page 14 of 22 4.1.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 15 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 16 of 22 5.UnwantedEmissionsInNon-restrictedFrequencyBands 5.1Ref 5.1.1TestResult ModeTXTypeFrequency(MHz)AntLevelofReference(dBm) 1MSISO 240219.36 244019.38 248019.24 Note1:RefertoFCCPart15.247(d)andANSIC63.10-2020,thechannelcontainsthemaximumPSDlevelwasused toestablishthereferencelevel. Page 17 of 22 5.1.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_MCH_2440MHz_DataRate=_Ant1_NTNV Page 18 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 19 of 22 5.2CSE 5.2.1TestResult ModeTXTypeFrequency(MHz)AntLevelofReference(dBm)Limit(dBm)Verdict 1MSISO 240219.38-10.62Pass 244019.38-10.62Pass 248019.38-10.62Pass Note1:RefertoFCCPart15.247(d)andANSIC63.10-2020,thechannelcontainsthemaximumPSDlevelwasused toestablishthereferencelevel. Page 20 of 22 5.2.2TestGraph 1M_LCH_2402MHz_DataRate=_Ant1_NTNV 1M_LCH_2402MHz_DataRate=_Ant1_NTNV Page 21 of 22 1M_MCH_2440MHz_DataRate=_Ant1_NTNV 1M_HCH_2480MHz_DataRate=_Ant1_NTNV Page 22 of 22 1M_HCH_2480MHz_DataRate=_Ant1_NTNV ---End---

Report No.: 18220WC10106001FCC ID: 2AOKB-T8420SPage 1 of 32 Code:AB-RF-05-a FCC TEST REPORT Client Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Product Name: Floodlight Camera Date: Jul. 26, 2021 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC10106001FCC ID: 2AOKB-T8420SPage 2 of 32 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................... 5 1.1. Client Information ....................................................................................................................................... 5 1.2. Description of Device (EUT) ..................................................................................................................... 5 1.3. Auxiliary Equipment Used During Test ................................................................................................... 6 1.4. Description of Test Modes ........................................................................................................................ 6 1.5. List of channels ........................................................................................................................................... 6 1.6. Description Of Test Setup ......................................................................................................................... 7 1.7. Test Equipment List .................................................................................................................................... 8 1.8. Measurement Uncertainty ......................................................................................................................... 9 1.9. Description of Test Facility ........................................................................................................................ 9 2. Summary of Test Results ................................................................................................................................... 10 3. Conducted Emission Test ................................................................................................................................... 11 3.1. Test Standard and Limit .......................................................................................................................... 11 3.2. Test Setup .................................................................................................................................................. 11 3.3. Test Procedure .......................................................................................................................................... 11 3.4. Test Data .................................................................................................................................................... 11 4. Radiation Spurious Emission and Band Edge ................................................................................................ 16 4.1. Test Standard and Limit .......................................................................................................................... 16 4.2. Test Setup .................................................................................................................................................. 16 4.3. Test Procedure .......................................................................................................................................... 17 4.4. Test Data .................................................................................................................................................... 18 5. Maximum Peak Output Power Test .................................................................................................................. 26 5.1. Test Standard and Limit .......................................................................................................................... 26 5.2. Test Setup .................................................................................................................................................. 26 5.3. Test Procedure .......................................................................................................................................... 26 5.4. Test Data .................................................................................................................................................... 26 6. 6DB Occupy Bandwidth Test ............................................................................................................................. 27 6.1. Test Standard and Limit .......................................................................................................................... 27 6.2. Test Setup .................................................................................................................................................. 27 6.3. Test Procedure .......................................................................................................................................... 27 6.4. Test Data .................................................................................................................................................... 27 7. Power Spectral Density Test .............................................................................................................................. 28 7.1. Test Standard and Limit .......................................................................................................................... 28 7.2. Test Setup .................................................................................................................................................. 28 7.3. Test Procedure .......................................................................................................................................... 28 7.4. Te…

Text truncated - open the document above for the full version.

Page 1 of 39 Appendix Test Data Report No.:18220WC10106002Test Date:2021.7.7 Test Engineer:Auditor: Temperature:24.3°CRelative Humidity:56 % Pressure:1012 hPa 1. Duty Cycle 1.1 Ant1 1.1.1 Test Result Ant1 Mode TX Type Frequency (MHz) T_on (ms)Period (ms)Duty Cycle (%) Duty Cycle Correction Factor (dB) Max. DC Variation (%) 802.11bSISO 24128.608.7098.820.050.00 24378.608.7098.810.050.00 24628.608.7098.820.050.00 802.11gSISO 24121.431.5393.320.300.00 24371.431.5393.460.290.03 24621.431.5393.450.290.00 802.11n (HT20) SISO 24121.341.4493.040.310.03 24371.331.4492.750.330.00 24621.341.4493.100.310.00 Page 2 of 39 1.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Page 3 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 4 of 39 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 5 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Page 6 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 7 of 39 2. Bandwidth 2.1 OBW 2.1.1 Test Result ModeTX TypeFrequency (MHz)Ant99% Occupied Bandwidth (MHz)LimitVerdict 802.11bSISO 2412113.97/Pass 2437113.94/Pass 2462113.91/Pass 802.11gSISO 2412117.28/Pass 2437117.26/Pass 2462117.28/Pass 802.11n (HT20) SISO 2412118.24/Pass 2437118.23/Pass 2462118.21/Pass Page 8 of 39 2.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Page 9 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 10 of 39 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 11 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Page 12 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 13 of 39 2.2 6dB BW 2.2.1 Test Result ModeTX TypeFrequency (MHz)Ant6dB Bandwidth (MHz)LimitVerdict 802.11bSISO 241218.10>=0.5Pass 243719.05>=0.5Pass 246218.54>=0.5Pass 802.11gSISO 2412115.14>=0.5Pass 2437115.15>=0.5Pass 2462115.14>=0.5Pass 802.11n (HT20)SISO 2412115.14>=0.5Pass 2437115.15>=0.5Pass 2462115.15>=0.5Pass Page 14 of 39 2.2.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Page 15 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 16 of 39 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 17 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Page 18 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 19 of 39 3. Maximum Conducted Output Power 3.1 Power 3.1.1 Test Result ModeTX TypeFrequency (MHz) Measured Peak Output Power (dBm) Verdict Ant1Limit 802.11bSISO 241221.23<=30Pass 243721.60<=30Pass 246221.10<=30Pass 802.11gSISO 241223.25<=30Pass 243723.25<=30Pass 246223.14<=30Pass 802.11n (HT20) SISO 241221.38<=30Pass 243721.64<=30Pass 246221.26<=30Pass Note1: Antenna Gain: Ant1: 2.60dBi; 4. Maximum Power Spectral Density 4.1 PSD 4.1.1 Test Result ModeTX TypeFrequency (MHz) Maximum PSD (dBm/3kHz) Verdict Ant1Limit 802.11bSISO 2412-3.42<=8Pass 2437-2.34<=8Pass 2462-3.25<=8Pass 802.11gSISO 2412-9.48<=8Pass 2437-9.23<=8Pass 2462-9.63<=8Pass 802.11n (HT20) SISO 2412-11.23<=8Pass 2437-10.40<=8Pass 2462-10.48<=8Pass Note1: Antenna Gain: Ant1: 2.60dBi; Page 20 of 39 4.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Page 21 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 22 of 39 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 23 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Page 24 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 25 of 39 5. Unwanted Emissions In Non-restricted Frequency Bands 5.1 Ref 5.1.1 Test Result ModeTX TypeFrequency (MHz)AntLevel of Reference (dBm) 802.11bSISO 2412110.74 2437111.08 2462110.87 802.11gSISO 241214.83 243715.11 246214.77 802.11n (HT20)SISO 241213.71 243713.85 246212.87 Note1: Refer to FCC Part 15.247 (d) and ANSI C63.10-2020, the channel contains the maximum PSD level was used to establish the reference level. Page 26 of 39 5.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Page 27 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 28 of 39 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 29 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Page 30 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 31 of 39 5.2 CSE 5.2.1 Test Result ModeTX TypeFrequency (MHz)AntLevel of Reference (dBm)Limit (dBm)Verdict 802.11bSISO 2412111.08-8.92Pass 2437111.08-8.92Pass 2462111.08-8.92Pass 802.11gSISO 241215.11-14.89Pass 243715.11-14.89Pass 246215.11-14.89Pass 802.11n (HT20) SISO 241213.85-16.15Pass 243713.85-16.15Pass 246213.85-16.15Pass Note1: Refer to FCC Part 15.247 (d) and ANSI C63.10-2020, the channel contains the maximum PSD level was used to establish the reference level. Page 32 of 39 5.2.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV Page 33 of 39 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV Page 34 of 39 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Page 35 of 39 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV Page 36 of 39 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Page 37 of 39 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV Page 38 of 39 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV Page 39 of 39 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV ---End---

Report No.: 18220WC10106002FCC ID: 2AOKB-T8420SPage 1 of 34 Code:AB-RF-05-a FCC TEST REPORT Client Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Product Name: Floodlight Camera Date: Jul. 26, 2021 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC10106002FCC ID: 2AOKB-T8420SPage 2 of 34 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................... 5 1.1. Client Information ....................................................................................................................................... 5 1.2. Description of Device (EUT) ..................................................................................................................... 5 1.3. Auxiliary Equipment Used During Test ................................................................................................... 6 1.4. Description of Test Modes ........................................................................................................................ 6 1.5. List of channels ........................................................................................................................................... 7 1.6. Description Of Test Setup ......................................................................................................................... 8 1.7. Test Equipment List .................................................................................................................................... 9 1.8. Measurement Uncertainty ....................................................................................................................... 10 1.9. Description of Test Facility ...................................................................................................................... 10 2. Summary of Test Results ................................................................................................................................... 11 3. Conducted Emission Test ................................................................................................................................... 12 3.1. Test Standard and Limit .......................................................................................................................... 12 3.2. Test Setup .................................................................................................................................................. 12 3.3. Test Procedure .......................................................................................................................................... 12 4. Radiation Spurious Emission and Band Edge ................................................................................................ 17 4.1. Test Standard and Limit .......................................................................................................................... 17 4.2. Test Setup .................................................................................................................................................. 17 4.3. Test Procedure .......................................................................................................................................... 18 4.4. Test Data .................................................................................................................................................... 19 5. Maximum Output Power Test ............................................................................................................................ 28 5.1. Test Standard and Limit .......................................................................................................................... 28 5.2. Test Setup ............................................................... ................................................................................... 28 5.3. Test Procedure .......................................................................................................................................... 28 5.4. Test Data .................................................................................................................................................... 28 6. 6DB Occupy Bandwidth Test ............................................................................................................................. 29 6.1. Test Standard and Limit .......................................................................................................................... 29 6.2. Test Setup .................................................................................................................................................. 29 6.3. Test Procedure .......................................................................................................................................... 29 6.4. Test Data .................................................................................................................................................... 29 7. Power Spectral Density Test .............................................................................................................................. 30 7.1. Test Standard and Limit .......................................................................................................................... 30 7.2. Test Setup .................................................................................................................................................. 30 7.3. Test Procedure .......................................................................................................................................... 30 7.4. Test Data .................................................................................................................................................... 30 8. …

Text truncated - open the document above for the full version.

FCCID:2AOKB-T8420S PhotoofPowerLineConductedEmissionTest PhotoofRadiationEmissionTest