2AOKB-T8425SFloodlight Cam E340

QUICK START GUIDE Floodlight Cam E340 Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005004126 V1 0201 SAFETY INSTRUCTIONS • This equipment is not suitable for use in locations where children are likely to be present. This equipment is not intended for use by children. • CET ÉQUIPEMENT NE CONVIENT PAS À UNE UTILISATION DANS DES ENDROITS OÙ DES ENFANTS SONT SUSCEPTIBLES D’ÊTRE PRÉSENTS. CET ÉQUIPEMENT N’EST PAS DESTINÉ À ÊTRE UTILISÉ PAR DES ENFANTS. • Do not use the product in any way other than described herein in order to avoid personal injury or property damage. • N’utilisez pas le produit d’une autre manière que celle décrite dans les présentes afin d’éviter des blessures corporelles ou des dommages matériels. • User should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Our company will not be responsible for any violators' legal liability under any circumstances. • L’utilisateur doit se conformer aux lois et réglementations des pays et régions correspondants où l’équipement est situé (utilisé), respecter l’éthique professionnelle, prêter attention aux obligations de sécurité et interdire strictement l’utilisation de nos produits ou équipements à des fins illégales. Notre société ne sera en aucun cas responsable de la responsabilité légale des contrevenants. • An appropriate disconnect device shall be provided as part of the building installation • An all-pole mains switch in accordance with Annex L shall be incorporated in the electrical installation of the building • Un dispositif de déconnexion approprié doit être prévu dans le cadre de l’installation du bâtiment. • Un interrupteur secteur tous pôles conforme à l’annexe L est incorporé dans l’installation électrique du bâtiment • The luminaire internded to be mounted on or over an outlet box and shall be provided with supply conductors long enough to extend 150mm(6 in) into the outlet box. • Le luminaire doit être monté sur ou au-dessus d'une boîte de sortie et doit être fourni avec des conducteurs d'alimentation suffisamment longs pour s'étendre de 150 mm (6 po) dans la boîte de sortie. • Caution, risk of electric shock • Attention, risque de choc électrique THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS MIN 90°C SUPPLY CONDUCTORS LES FILS D’ALIMENTATION 90°C MIN 0403 AT A GLANCE ⑩ ⑧ ⑦ ④ ⑪ ① ② ③ ⑤ ⑥ ⑫ ⑨ SYNC ① Floodlight ⑧ Power Input (For Quick Setup) ② Speaker ⑨ SYNC Button ③ Motion Sensor Component ⑩ microSD Card Slot ④ System Indicator Insert a microSD card* (not provided) to store recordings ⑤ Telephoto Camera ⑥ Wide Angle Camera ⑪ Mounting Bracket ⑦ Infrared Component ⑫ Mounting Base *Use at least a Class 10 microSD card with a maximum of 128 GB. WHAT'S IN THE BOX Floodlight Cam E340 Model: T8425 USB Cable (For Quick Setup Only) Mounting Bracket (Pre-installed on Camera) Positioning Sticker Installation Hook Wall Screws (Bag A) Base Screws (Bag B) Bracket and Earth Screws (Bag C) Warning Sticker Quick Start Guide WHAT YOU NEED (Not Provided) #2 or #1 Phillips Crosshead Screwdriver 5V/1A USB Power Adapter Ladder (If necessary) 0605 3. Tap + in the app and follow the in-app instructions to add the camera. My Devices 4. Disconnect from the power adapter, then close the USB port cover. SYNCPower SD Card Shut power off at the breaker If you don’t know where your breaker is or how to turn off power to your floodlight circuit, consult with a licensed electrician. SETTING UP THE SYSTEM 1. Download and install the eufy Security app, then sign in or create an account. 2. Power on the floodlight camera by using the USB-C charging cable and a power adapter (5V/1A, not provided). SYNC The USB port cover must be closed to prevent water from entering the floodlight camera. • To avoid scratching the floodlight camera, do not peel off the protective film for the time being. • The floodlights will only light up when in wired power mode. The USB- powered connection is used for setting up the camera safely inside your home. • Make sure you can stream video from your floodlight camera BEFORE INSTALLATION. 0807 PREPARING FOR INSTALLATION (IMPORTANT) Check local laws for installation If you are outside of North America, installation and wiring must be performed by a licensed electrician. Always follow code standards when installing wired connections. Shut Power Off at the Breaker OFF OFF WARNING: electrical shock • • • Properly ground fixture. • Always follow code standards when installing wired connections. • If you are outside of North America, installation and wiring must be performed by a licensed electrician. CAUTION: Risk of fire • Do not install near combustible or flamable surfaces. Shut power off at the If you don’t know where your breaker is or how to turn off power to your floodlight circuit, consult with a licensed electrician. Risk of Electrical Shock • Turn off the power at your circuit breaker or fuse box before continuing, consult with a licensed electrician if needed. • Switch on/off the lights to make sure the electricity to the installation area is shut off. • Verify that the power supply is a 100~240 VAC 50/60 Hz power source. • Keep the breaker off at any time during the installation process. NOTE: Do not use a dimmer switch or timer for this product. INSTALLING YOUR FLOODLIGHT CAMERA Separate the Mounting Bra…

Text truncated - open the document above for the full version.

CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 2023-09-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID:2AOKB-T8425S Anker Innovations Limited (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Anker Innovations Limited (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Contact Person: Louis Qi Title: Manager Company Name& Address: Anker Innovations Limited & Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong

U.S. AGENT LETTER OF ATTESTATION Date: 2023-09-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID:2AOKB-T8425S Anker Innovations Limited (“the Applicant”) certifies that, as of the date of the filing of the application, Fantasia Trading LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Anker Innovations Limited (“the Applicant”) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Fantasia Trading LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Fantasia Trading LLC Address: 5350 Ontario Mills Pkwy, STE 100, Ontario, CA 91764 FRN: 0033423005 Tel.: +1 (800)988 7973 Email: [email protected] Signed by (printed name): Louis Qi Signature: Applicant: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong FRN: 0027073105 Tel: +86-755-86544807 Email: [email protected] Signed by (printed name): Louis Qi Signature:

Anker Innovations Limited Add: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel: +86-755-86544807 Email: [email protected] Attestation Letter Date: 2023-09-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: Our product Floodlight Cam E340, model: T8425, FCC ID:2AOKB-T8425S,for marketing purpose, this product only supports BLE 1M.2.4G WiFi(2412-2462MHz, 802.11b/g/n ht20/ax20 modes,2422-2452MHz,802.11n ht40/ax40 modes),5.2G WiFi(5150-5250MHz, 802.11a/n ht20/ac vht20/ax hew20/n ht40/ac vht40/ax hew40 modes),5.3G WiFi(5250-5350MHz, 802.11a/n ht20/ac vht20/ax hew20/n ht40/ac vht40/ax hew40 modes),5.6G WiFi(5470-5725MHz, 802.11a/n ht20/ac vht20/ax hew20/n ht40/ac vht40/ax hew40 modes),5.8G WiFi(5725-5850MHz, 802.11a/n ht20/ac vht20/ax hew20/n ht40/ac vht40/ax hew40 modes),The other functions, bands and modes was disabled to use by manufacturer in the software, the end user has no capability to activate it. Sincerely, Printed Name: Louis Qi Title: Manager

QA-FR-170-B Anker Innovations Limited Add: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel: +86-755-86544807 Email: [email protected] FCC Authorization Date: 2023-09-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , Anker Innovations Limited, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Louis Qi Title: Manager

QA-FR-172-A Anker Innovations Limited Add: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel: +86-755-86544807 Email: [email protected] FCC Confidential Authorization Date: 2023-09-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:2AOKB-T8425S In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Anker Innovations Limited hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Device Security Declaration As well as short-term (secrecy cycle:180 days) confidential treatment of information accompanying this application as outlined below:  Internal Photos  User’s Manual  External Photos  Test Set-up Photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature Printed Name: Louis Qi Title: Manager

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-EXP Page 1 of 5 EUT EXTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-EXP Page 2 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-EXP Page 3 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-EXP Page 4 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-EXP Page 5 of 5

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 1 of 18 EUT INTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 2 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 3 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 4 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 5 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 6 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 7 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 8 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 9 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 10 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 11 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 12 of 18 BLE&Wifi Antenna China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 13 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 14 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 15 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 16 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 17 of 18 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-INP Page 18 of 18

RF EXPOSURE EVALUATION Applicant: Anker Innovations Limited Address: Room 1318-19,Hollywood Plaza,610 Nathan Road, Mongkok, Kowloon, Hong Kong FCC ID: 2AOKB-T8425S Product Name: Floodlight Cam E340 Standard(s): 47 CFR §1.1310, 47 CFR §2.1091 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230850745-00F Date Of Issue: 2023/9/29 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00F Page 2 of 6 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00F Page 3 of 6 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 4 FCC§1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ............................... 5 1.1 APPLICABLE STANDARD ...................................................................................................................... 5 1.2 EUT INFORMATION▲: ........................................................................................................................ 6 1.3 MEASUREMENT RESULT ..................................................................................................................... 6 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00F Page 4 of 6 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 1.0 CR230850745-00F Original Report 2023/9/29 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00F Page 5 of 6 FCC§1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculation formula: Prediction of power density at the distance of the applicable MPE limit S = PG/4R² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); For simultaneously transmit system, the calculated power density should comply with: China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00F Page 6 of 6 1.2 EUT Information▲: Operation Modes Operation Frequency (MHz) Max Conducted output power including Tune-up Tolerance (dBm) Maximum Antenna Gain (dBi) BLE 2402-248042.9 2.4G WLAN 2412-2462242.9 5.2G WLAN 5150-5250154.8 5.3G WLAN 5250-5350164.8 5.6G WLAN 5470-5725114.8 5.8G WLAN 5725-5850144.8 Note: 1. The Above Parameters were provided by the manufacturer. 1.3 Measurement Result Operation Modes Frequency (MHz) Antenna Gain Conducted output power including Tune-up Tolerance Evaluation Distance Power Density MPE Limit (dBi) (numeric)(dBm) (mW) (cm) (mW/cm 2 )(mW/cm 2 ) BLE 2402-2480 2.9 1.95 4 2.51 20.00 0.0010 1 2.4G WLAN 2412-2462 2.9 1.95 24 251.19 20.00 0.0975 1 WIFI 5G 5150-5250 4.8 3.02 15 31.62 20.00 0.0190 1 5250-5350 4.8 3.02 16 39.81 20.00 0.0239 1 5470-5725 4.8 3.02 11 12.59 20.00 0.0076 1 5725-5850 4.8 3.02 14 25.12 20.00 0.0151 1 Note: The 2.4G Wifi, 5G Wifi or BLE can’t transmit simultaneously. Result: The device compliant the Exemption at 20cm distances. ===== END OF REPORT =====

0 A letter of recognition Customer Admit confirm ID DepartmentTest departmentStructure section Quality department Supplier Admit confirm confirmProofreadingTo examineApproval ZhangwanzheXuliying APPROVAL No.ATCSZ-5-180124-001ISSUE1 DESCRIBE: Anker Innovations Co., LTD （ T8425 ) Customer NO: 290000-019518 PART NO: ATC1357-HY049B70RA Antenna type: 2.4G&5.8 ANT FPC+CABLE DATE: 2023.07.04 PROVIDER: AT&C TECHNOLOGIES(SHENZHEN) CO. LTD 1 ANT 2 Antenna S11 3 Antenna *Efficiency Frequency/MHz EfficiencyGain . dbi 2400 57%2.8 2410 57%2.9 2420 57%2.7 2430 56%2.6 2440 57%2.4 2450 54%2.3 2460 57%2.2 2470 57%2.2 2480 55%2.6 2490 56%2.8 2500 53%2.7 4 Frequency/MHz EfficiencyGain . dbi 5000 54%4.4 5100 55%4.5 5200 67%4.6 5300 52%4.7 5400 55%4.7 5500 59%4.8 5600 56%3.2 5700 52%2.9 5800 55%3.8 5900 51%4.7 6000 50%4.6 Antenna *Efficiency 5 Directional pattern TEST 6 Directional pattern TEST 7 Directional pattern TEST 8 Directional pattern TEST 9 Directional pattern TEST 10 Directional pattern TEST 11 Antenna Draw Size informationMeasuring sample % Tolerance Handling opinions nu mb er Dime nsion prope rty Dimen sion Lower to lerance Upper t oleranc e 123 UpperLower determi ne Supplier r eview co mments Custo mer re view c omme nts Measuring tool 1 key p oint 25.84-0.250.2525.8725.7925.82PASS PJ 2 key p oint 36.08-0.300.3036.0636.1236.07PASS PJ 3 key p oint 1.4-0.10.11.361.361.43PASS PJ 4 key p oint 40-1.51.540.839.540.3PASS PJ 12 Production process 13 Packaging method PE bag packaging, product emission neat, uniform quantity PART LIST The packing drawing is schematic diagram, which does not mean that the picture is the actual produc tand the actual shipment is the standard. NODESCRIPTIONQ'TYMATERIALREMARKSREV. 1 ANTENNA1/1000N/AA 2 PAD OUT 1/4 SW A골 5TN/AA 4 CARTOON BOX-SW A골 5TN/AA 5 PACKING TAPE-PPN/AA Picture: Outer box "I" seal, QC PASS seal on the left side of the outer box, sealed without exposure.

TEST REPORT Applicant: Anker Innovations Limited Address: Room 1318-19,Hollywood Plaza,610 Nathan Road, Mongkok, Kowloon, Hong Kong FCC ID: 2AOKB-T8425S Product Name: Floodlight Cam E340 Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230850745-00A Date Of Issue: 2023/9/25 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00A Page 2 of 67 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00A Page 3 of 67 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 8 1.2.1 EUT Operation Condition: ............................................................................................................................. 8 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 9 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................ 10 2. SUMMARY OF TEST RESULTS .......................................................................................... 11 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 12 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 12 3.1.1 Applicable Standard ..................................................................................................................................... 12 3.1.2 EUT Setup.................................................................................................................................................... 13 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 13 3.1.4 Test Procedure ............................................................................................................................................. 14 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 14 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 15 3.2.1 Applicable Standard ..................................................................................................................................... 15 3.2.2 EUT Setup.................................................................................................................................................... 15 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 16 3.2.4 Test Procedure ............................................................................................................................................. 16 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 16 3.3 MINIMUM 6 DB EMISSION BANDWIDTH ...........................................................................…

Text truncated - open the document above for the full version.

TEST REPORT Applicant: Anker Innovations Limited Address: Room 1318-19,Hollywood Plaza,610 Nathan Road, Mongkok, Kowloon, Hong Kong FCC ID: 2AOKB-T8425S Product Name: Floodlight Cam E340 Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230850745-00B Date Of Issue: 2023/9/25 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00B Page 2 of 40 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230850745-00B Page 3 of 40 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .................................................................................................…

Text truncated - open the document above for the full version.