2AOKB-T8506eufy Security C220 Smart Lock

QUICK START GUIDE eufy Security C220 Smart Lock Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. Model: T8506 V01 01 ENEN 02 ③ ① ④ ② Set ① Battery Compartment ② Setup Button ③ Thumbturn ④ Screw Hole AT A GLANCE ③ ⑤ ① ④ ② ⑥ ① Fingerprint Button ② Battery Indicator ③ Keypad ④ Status Light and Lock / Unlock Button •Blue: Door unlocked •Orange: Door locked •Red: Abnormal state ⑤ Keyway: Can be copied, can't be rekeyed. ⑥ USB-C Port: Charges the lock in emergency situations. 03 ENEN 04 INSTALLATION Step 1. Prepare the Door 1. Remove the existing lock and check your door. 2. Check if your door has holes like the one below. Standard US doors are already compatible. • If not, follow the template to drill holes on your door. Backset 2 ⅜ " / 60 mm or 2¾" / 70 mm Minimum Distance 1⁴⁹/₆₄" / 45 mm Door Hole Diameter 1" / 25 mm Door Thickness 1 ⅜ " - 2¹¹/₆₄" 35 mm - 55 mm Cross Bore Diameter 1 ½" / 38 mm 2 ⅛" / 54 mm WHAT'S INCLUDED For Smart Lock Installation (Step 2) Deadbolt Installation Set B A (Step 3) Exterior Assembly C (Step 4) Interior Assembly Installation Set F GH E D (Step 5) Strike Plate Installation Set K J I Deadbolt Exterior Assembly Interior Assembly Strike PlateyStrike ScrewsKeys Screws Silicone Plug Interior Assembly Screws Batteries Deadbolt Screws / Strike Screws 05 ENEN 06 *Check the latch hole before inserting the deadbolt. If the latch hole is round, refer to diagram A. If the latch hole is rectangular, refer to diagram B. ❷ ❶ ❸ ❹ Make sure the word "TOP" on the deadbolt faces up. If the latch hole is round, contact customer service to receive a round drive- in faceplate, then replace the existing one. Diagram A Diagram B Step 2. Install Deadbolt 1. Check your door to see if the deadbolt requires adjustment. 2-3/8 2-3/4 180° 2⅜" / 60 mm 2¾" / 70 mm 2. Insert and screw the deadbolt into the doorframe. B A If the backset is 60mm, insert the deadbolt directly. If the backset is 70mm, rotate the faceplate of the deadbolt 180° to extend the length. Backset Latch Hole Deadbolt Deadbolt Screws / Strike Screws 07 ENEN 08 Step 4. Install Interior Assembly 1. Detach the back cover from the interior assembly. 2. Run the wires through the back cover. Step 3. Install Exterior Assembly • Remove the spacer before installation if you have a 38 mm cross bore. Cross Bore Diameter 1 ½" / 38 mm 09 ENEN 10 5. Mount the interior assembly. Make sure both wires are tucked into the cabin on the back of the interior assembly. Set Set 3. Secure the back cover with screws. E 4. Wire to the interior assembly. Tightly fasten the screws in place. Set the screws with your hands, then use a screwdriver to secure them. Make sure the deadbolt is retracted and the thumb turn knob is on the 'unlock' position, check if the deadbolt moves properly by turning the thumbturn. Screws 11 ENEN 12 6.Install the 8 AA batteries provided with the correct polarity. Don't put on the cover until the system setup is done in the app. *For your convenience, please first install the bottom layer of 4 AA batteries. Set H Friendly Reminder: When removing the batteries, first remove the upper layer, then gently pull the ribbon to lift the remaining batteries out of the compartment. Set Set F G Set Set *Use a long screwdriver to fasten the Interior Assembly screws. Silicone Plug Interior Assembly Screws Batteries 13 ENEN 14 SETTING UP THE SYSTEM 1. Download and install the eufy Security app, then sign up for an account. 2.Follow the in-app instructions to add the Smart Lock C220 to your device list. • Please visit https://support.eufylife.com/s/ or scan the QR code for more information. Step 5. Install Strike Plate J I Make sure the depth of the latch hole on door frame is deep enough (1" / 25.4 mm), otherwise the calibration might fail during the setup. Latch Hole Depth 25.4mm/1'' Strike PlateyStrike Screws 15 ENEN 16 FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004 Telephone:1-800-988-7973 Notice (Australia) Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for the device and accessories is -20°C to 50°C . It is recommended to supply the device in an environment with a temperature that ranges from 5°C~25°C. When supplying, please place the device in an environment that has a normal room temperature and good ventilation. Warning: • replacement of a battery with an incorrect type that can defeat a safeguard; • disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; • leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and • a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the e…

Text truncated - open the document above for the full version.

Anker Innovations Limited 2.911(d)(5)(i)EquipmentTypeAttestationv1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: eufy Security Smart Lock C220 FCC ID: 2AOKB-T8506 Model(s): T8506 2.911(d)(5)(i)EquipmentType We, [Anker Innovations Limited] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Louis QiDate: 2023-06-28 Title and Company name: Compliance Manager / Anker Innovations Limited NOTE 1 “Covered List ” ; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Anker Innovations Limited 2.911(d)(5)(ii)ApplicantAttestationv1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List) Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: eufy Security Smart Lock C220 FCC ID: 2AOKB-T8506 Model(s): T8506 2.911(d)(5)(ii) Applicant filing We, [Anker Innovations Limited] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Louis QiDate: 2023-06-28 Title and Company name: Compliance Manager / Anker Innovations Limited NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List ” ; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Anker Innovations Limited 2.911(d)(7)USAAgentv1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: Address: Product Name: eufy Security C220 Smart Lock FCC ID: 2AOKB-T8506 Model(s): T8506 2.911(d)(7) USA Designated Agent for Service of Process We, [Anker Innovations Limited] (“the applicant”) designate [Fantasia Trading LLC] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA AgentApplicant Company name: Fantasia Trading LLCCompany name: Anker Innovations Limited Address: 5350 Ontario Mills Pkwy, STE 100, Ontario, CA 91764 Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong FRN of U.S. agent: 0033423005 FRN:0027073105 FCC ID Number:2AOKB-T8506FCC ID Number: 2AOKB-T8506 Contact Name: Louis QiContact Name: Louis Qi Telephone No: +1 (800)988 7973Telephone No: +1 (800)988 7973 Email: [email protected]: [email protected] Signature:Signature: Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Fantasia Trading LLC 2.911(d)(7)USAAgentv1.2 Title: Compliance ManagerTitle: Compliance Manager Date: 2023-07-07Date: 2023-07-07 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

AnkerInnovationsLimited AgentAuthorizationLetter (7/14/2023) RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,authorizeMicomLabsInc.,575BoulderCourt,Pleasanton,California94566, USAtoactonourbehalfinallmattersrelatingtoapplicationforequipment authorization,includingthesigningofalldocumentsrelatingtothesematters. Thisagreementexpiresoneyearfromthecurrentdate. Sincerely, LouisQi/Manager CompanyName:AnkerInnovationsLimited Address:Room1318-19,HollywoodPlaza,610NathanRoad,Mongkok,Kowloon, HongKong

AnkerInnovationsLimited OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023-07-14 Subject;RequestforConfidentiality FCCID:2AOKB-T8506 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription SWSECURITYDESCRIPTION PartsList Tuneup Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:louisQi Title:Manager

ProjectNo.:18220WC301230Page1of7 Code:AB-RF-05-b AppendixII--ExternalPhotograph ProjectNo.:18220WC301230Page2of7 Code:AB-RF-05-b ProjectNo.:18220WC301230Page3of7 Code:AB-RF-05-b ProjectNo.:18220WC301230Page4of7 Code:AB-RF-05-b ProjectNo.:18220WC301230Page5of7 Code:AB-RF-05-b ProjectNo.:18220WC301230Page6of7 Code:AB-RF-05-b ProjectNo.:18220WC301230Page7of7 Code:AB-RF-05-b

ProjectNo.:18220WC301230Page1of4 Code:AB-RF-05-b AppendixIII--InternalPhotograph ProjectNo.:18220WC301230Page2of4 Code:AB-RF-05-b ProjectNo.:18220WC301230Page3of4 Code:AB-RF-05-b ProjectNo.:18220WC301230Page4of4 Code:AB-RF-05-b BT-ANT WIFIANT

RFEXPOSUREEVALUATION AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeusedto evaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF)Radiation asspecifiedin§1.1307(b) FCCID:2AOKB-T8506 EUTSpecification EUTeufySecurityC220SmartLock Frequencyband(Operating)WLAN:2.412GHz~2.462GHz WLAN:5.18GHz~5.24GHz WLAN:5.745GHz~5.825GHz Others:Bluetooth:2402-2480MHz DevicecategoryPortable(<20cmseparation) Mobile(>20cmseparation) Others___ ExposureclassificationOccupational/Controlledexposure(S=5mW/cm2) GeneralPopulation/Uncontrolledexposure(S=1mW/cm2) AntennadiversitySingleantenna Multipleantennas Txdiversity Rxdiversity Tx/Rxdiversity Antennagain(Max) BLE:3.7dBi WIFI2.4G:3.5dBi EvaluationappliedMPEEvaluation SAREvaluation LimitsforMaximumPermissibleExposure(MPE) Frequency Range(MHz) ElectricField Strength(V/m) MagneticField Strength(A/m) Power Density(mW/cm 2 ) Average Time (A)LimitsforOccupational/ControlExposures 300-1500----F/3006 1500-100000----56 (B)LimitsforGeneralPopulation/UncontrolExposures 300-1500----F/15006 1500-100000----130 Friistransmissionformula:Pd=(Pout*G)\(4*pi*R2) Where Pd=PowerdensityinmW/cm 2 Pout=outputpowertoantennainMw G=gainofantennainlinearscale Pi=3.1416 R=distancebetweenobservationpointandcenteroftheradiatorincm PdthelimitofMPE,1mW/cm2.Ifweknowthemaximumgainoftheantennaand totalpowerinputtotheantenna,throughthecalculation,wewillknowthedistance wheretheMPElimitisreached. MaxMeasurementResult Operating Mode Measured Power Tuneup tolerance Max.Tune upPower Antenna Gain Power densityat 20cm Power densityLimits (mW/cm2) (dBm)(dBm)(dBm)(dBi)(mW/cm2) WIFI2.4G 6.136.13±17.133.50.0023 1 BLE 23.0923.09±124.093.70.1196 1 TheWLAN2.4GandBLEcantransmitsimultaneously: =S WIFI 2.4/Slimit-2.4+SBLE/Slimit-BLE =0.0023/1+0.1196/1 =0.1219 <1.0 Result:NoStandaloneSARtestisrequired.

ReportNo.:18220WC30123001FCCID:2AOKB-T8506Page1of30 Code:AB-RF-05-b FCCTestReport Applicant:AnkerInnovationsLimited Address: Room1318-19,HollywoodPlaza,610Nathan Road,Mongkok,Kowloon,HongKong ProductName:eufySecurityC220SmartLock ReportDate:Jul.14,2023 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC30123001FCCID:2AOKB-T8506Page2of30 Code:AB-RF-05-b Contents 1.GeneralInformation............................................................................................................................................6 1.1.ClientInformation....................................................................................................................................6 1.2.DescriptionofDevice(EUT)..................................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest.................................................................................................7 1.4.DescriptionofTestConfiguration..........................................................................................................7 1.5.DescriptionOfTestSetup......................................................................................................................8 1.6.TestEquipmentList.................................................................................................................................9 1.7.MeasurementUncertainty....................................................................................................................10 1.8.DescriptionofTestFacility...................................................................................................................10 2.SummaryofTestResults.................................................................................................................................11 3.ConductedEmissionTest................................................................................................................................12 3.1.TestStandardandLimit........................................................................................................................12 3.2.TestSetup...............................................................................................................................................12 3.3.TestProcedure.......................................................................................................................................12 3.4.TestData.................................................................................................................................................12 4.RadiationSpuriousEmissionandBandEdge.............................................................................................15 4.1.TestStandardandLimit........................................................................................................................15 4.2.TestSetup...............................................................................................................................................15 4.3.TestProcedure.......................................................................................................................................16 4.4.TestData.................................................................................................................................................17 5.MaximumPeakOutputPowerTest...............................................................................................................25 5.1.TestStandardandLimit........................................................................................................................25 5.2.TestSetup...............................................................................................................................................25 5.3.TestProcedure.......................................................................................................................................25 5.4.TestData.................................................................................................................................................25 6.6DBOccupyBandwidthTest..........................................................................................................................26 6.1.TestStandardandLimit........................................................................................................................26 6.2.TestSetup...............................................................................................................................................26 6.3.TestProcedure.......................................................................................................................................26 6.4.TestData.................................................................................................................................................26 7.PowerSpectralDensityTest...........................................................................................................................27 7.1.TestStandardandLimit........................................................................................................................27 7.2.TestSetup...............................................................................................................................................27 7.3.TestProcedure.......................................................................................................................................27 7.4.TestData.................................................................................................................................................27 8.100kHzBandwidthofFrequencyBandEdgeRequirement......................................................................28 8.1.TestStandardandLimit........................................................................................................................28 8.2.TestSetup.............................…

Text truncated - open the document above for the full version.

Page1of44 AppendixTestData ReportNo.:18220WC30123002TestSampleNo.:1-2-2 StartTestDate:2023.06.20FinishTestDate:2023.07.11 TestEngineer:Auditor: Temperature:25.9°CRelativeHumidity:49% Pressure:1012hPa AppendixA:DTSBandwidth TestResult TestModeAntennaFrequency[MHz] DTSBW [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 11BAnt1 241210.0402407.0002417.040≥0.5PASS 243710.0402432.0002442.040≥0.5PASS 246210.0402457.0002467.040≥0.5PASS 11GAnt1 241216.2802403.8802420.160≥0.5PASS 243716.0402428.8802444.920≥0.5PASS 246216.3202453.8402470.160≥0.5PASS 11N20SISOAnt1 241215.8802403.8802419.760≥0.5PASS 243716.6002428.9202445.520≥0.5PASS 246212.8802455.3602468.240≥0.5PASS Page2of44 TestGraphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Page3of44 11G_Ant1_2412 11G_Ant1_2437 Page4of44 11G_Ant1_2462 11N20SISO_Ant1_2412 Page5of44 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Page6of44 Page7of44 AppendixB:OccupiedChannelBandwidth TestResult TestModeAntenna Channel Frequency[MHz] OCB [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 11BAnt1 241213.1512405.50072418.6517------ 243713.4282430.34272443.7707------ 246213.1142455.49282468.6068------ 11GAnt1 241216.3882403.83342420.2214------ 243716.4262428.82122445.2472------ 246216.4272453.80602470.2330------ 11N20SISOAnt1 241217.3192403.37672420.6957------ 243717.3312428.38982445.7208------ 246217.3092453.36792470.6769------ Page8of44 TestGraphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Page9of44 11G_Ant1_2412 11G_Ant1_2437 Page10of44 11G_Ant1_2462 11N20SISO_Ant1_2412 Page11of44 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Page12of44 Page13of44 AppendixC:Maximumconductedoutputpower TestResultPeak TestModeAntennaFrequency[MHz]PeakPower[dBm] Conducted Limit[dBm] 11BAnt1 241221.68≤30.00 243723.09≤30.00 246221.80≤30.00 11GAnt1 241220.37≤30.00 243722.10≤30.00 246220.26≤30.00 11N20SISOAnt1 241220.17≤30.00 243722.16≤30.00 246220.09≤30.00 Page14of44 AppendixD:Maximumpowerspectraldensity TestResult TestModeAntennaFrequency[MHz]Result[dBm/3kHz]Limit[dBm/3kHz]Verdict 11BAnt1 2412-1.91≤8.00PASS 2437-0.4≤8.00PASS 2462-2.14≤8.00PASS 11GAnt1 2412-10.94≤8.00PASS 2437-9.47≤8.00PASS 2462-10.02≤8.00PASS 11N20SISOAnt1 2412-11.71≤8.00PASS 2437-7.17≤8.00PASS 2462-11.37≤8.00PASS Page15of44 TestGraphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Page16of44 11G_Ant1_2412 11G_Ant1_2437 Page17of44 11G_Ant1_2462 11N20SISO_Ant1_2412 Page18of44 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Page19of44 Page20of44 AppendixE:Bandedgemeasurements TestResult TestMode Antenn a ChNam e Frequency[MH z] RefLevel[dB m] Result[dB m] Limit[dBm ] Verdic t 11BAnt1 Low24129.66-32.25≤-10.34PASS High24629.34-41.4≤-10.66PASS 11GAnt1 Low24120.03-35.72≤-19.97PASS High24622.69-43.84≤-17.31PASS 11N20SIS O Ant1 Low24123.62-28.32≤-16.38PASS High24621.67-44.12≤-18.33PASS Page21of44 TestGraphs 11B_Ant1_Low_2412 11B_Ant1_High_2462 11G_Ant1_Low_2412 Page22of44 11G_Ant1_High_2462 11N20SISO_Ant1_Low_2412 Page23of44 11N20SISO_Ant1_High_2462 Page24of44 AppendixF:ConductedSpuriousEmission TestResult TestModeAntennaFrequency[MHz] FreqRange [Mhz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict 11BAnt1 2412 Reference8.808.80---PASS 30~10008.80-68.33≤-11.2PASS 1000~265008.80-53.54≤-11.2PASS 2437 Reference10.9310.93---PASS 30~100010.93-67.73≤-9.07PASS 1000~2650010.93-53.99≤-9.07PASS 2462 Reference8.918.91---PASS 30~10008.91-69.18≤-11.09PASS 1000~265008.91-53.67≤-11.09PASS 11GAnt1 2412 Reference-0.21-0.21---PASS 30~1000-0.21-69.01≤-20.21PASS 1000~26500-0.21-53.43≤-20.21PASS 2437 Reference1.191.19---PASS 30~10001.19-69.16≤-18.81PASS 1000~265001.19-53.57≤-18.81PASS 2462 Reference-0.92-0.92---PASS 30~1000-0.92-68.86≤-20.92PASS 1000~26500-0.92-53.74≤-20.92PASS 11N20SISOAnt1 2412 Reference-1.21-1.21---PASS 30~1000-1.21-68.72≤-21.21PASS 1000~26500-1.21-53.28≤-21.21PASS 2437 Reference0.890.89---PASS 30~10000.89-69.12≤-19.11PASS 1000~265000.89-53.49≤-19.11PASS 2462 Reference2.702.70---PASS 30~10002.70-68.95≤-17.3PASS 1000~265002.70-53.73≤-17.3PASS Page25of44 TestGraphs 11B_Ant1_2412_0~Reference 11B_Ant1_2412_30~1000 11B_Ant1_2412_1000~26500 Page26of44 11B_Ant1_2437_0~Reference 11B_Ant1_2437_30~1000 Page27of44 11B_Ant1_2437_1000~26500 11B_Ant1_2462_0~Reference Page28of44 11B_Ant1_2462_30~1000 11B_Ant1_2462_1000~26500 Page29of44 11G_Ant1_2412_0~Reference 11G_Ant1_2412_30~1000 Page30of44 11G_Ant1_2412_1000~26500 11G_Ant1_2437_0~Reference Page31of44 11G_Ant1_2437_30~1000 11G_Ant1_2437_1000~26500 Page32of44 11G_Ant1_2462_0~Reference 11G_Ant1_2462_30~1000 Page33of44 11G_Ant1_2462_1000~26500 11N20SISO_Ant1_2412_0~Reference Page34of44 11N20SISO_Ant1_2412_30~1000 11N20SISO_Ant1_2412_1000~26500 Page35of44 11N20SISO_Ant1_2437_0~Reference 11N20SISO_Ant1_2437_30~1000 Page36of44 11N20SISO_Ant1_2437_1000~26500 11N20SISO_Ant1_2462_0~Reference Page37of44 11N20SISO_Ant1_2462_30~1000 11N20SISO_Ant1_2462_1000~26500 Page38of44 Page39of44 AppendixG:DutyCycle TestResult TestModeAntennaFrequency[MHz] Transmission Duration [ms] Transmission Period[ms] DutyCycle [%] Factor 11BAnt1 24128.219.3887.530.58 24378.219.3887.530.58 24628.219.3887.530.58 11GAnt1 241212.0412.0599.920.00 243712.0312.0499.920.00 246212.0412.0599.920.00 11N20SISOAnt1 241211.1211.1399.910.00 243711.1211.1399.910.00 246211.1211.1399.910.00 Page40of44 TestGraphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Page41of44 11G_Ant1_2412 11G_Ant1_2437 Page42of44 11G_Ant1_2462 11N20SISO_Ant1_2412 Page43of44 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Page44of44 ---End---

ReportNo.:18220WC30123002FCCID:2AOKB-T8506Page1of31 Code:AB-RF-05-b FCCTestReport Applicant:AnkerInnovationsLimited Address: Room1318-19,HollywoodPlaza,610Nathan Road,Mongkok,Kowloon,HongKong ProductName:eufySecurityC220SmartLock ReportDate:Jul.14,2023 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC30123002FCCID:2AOKB-T8506Page2of31 Code:AB-RF-05-b Contents 1.GeneralInformation............................................................................................................................................6 1.1.ClientInformation.....................................................................................................................................6 1.2.DescriptionofDevice(EUT)..................................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest.................................................................................................7 1.4.DescriptionofTestConfiguration..........................................................................................................7 1.5.DescriptionOfTestSetup.......................................................................................................................8 1.6.TestEquipmentList.................................................................................................................................9 1.7.MeasurementUncertainty....................................................................................................................10 1.8.DescriptionofTestFacility....................................................................................................................10 2.SummaryofTestResults.................................................................................................................................11 3.ConductedEmissionTest................................................................................................................................12 3.1.TestStandardandLimit........................................................................................................................12 3.2.TestSetup...............................................................................................................................................12 3.3.TestProcedure.......................................................................................................................................12 3.4.TestData.................................................................................................................................................12 4.RadiationSpuriousEmissionandBandEdge.............................................................................................15 4.1.TestStandardandLimit........................................................................................................................15 4.2…

Text truncated - open the document above for the full version.