2AOKB-T9146CSmart Scale C1

T9146 51005003929 V01 Owner's Manual Smart Scale C1 EN 01 Thank you for purchasing Smart Scale C1. Carefully read all the instructions below before using this device, and keep this manual for future reference. Table of Contents 02 Important Safety Instructions 07 AUSTRALIA & NEW ZEALAND WARRANTY 09 What’s in the Box 09 Inserting the Batteries 10 Selecting the Measuring Unit 10 Installing the EufyLife App and Pairing 11 Starting a Measurement For body weight measurement For body composition analysis 13 Weight-Only Measurement 13 Maintenance 14 Troubleshooting Error Message 15 When Measuring 16 Specifications 17 Customer Service English01 Español18 Français37 02 ENEN 03 Important Safety Instructions • Read all instructions before using the device. Keep the manual for future reference. • Only use the device as described in this user manual. Any misuse may cause electric shocks, burns, start a fire or other unexpected hazards. • Be aware that this device is designed for individuals to measure their weight and to monitor their body composition. Any information provided by this device is in no way meant to treat, cure, or prevent diseases or illnesses from happening. • DO NOT use this device if you are pregnant or if you suspect you may be pregnant. The effects of this device on a fetus are unknown and untested. • DO NOT use this device if you use a wearable or implanted electronic device such as a defibrillator or pacemaker. • The device is equipped with a data transmission function that emits electromagnetic energy. Portable Radio Frequency (RF) communications equipment (including peripherals such as antenna cables and external antennas) should not be used within 30 cm (12 inches) of the device, otherwise, performance may be affected. • Do not modify this device. • Do not expose this device to extreme temperatures, direct sunlight, moisture, or corrosive environments. • To prevent slipping, do not step on the device after bathing or showering. • This device should not be used when it is adjacent to or stacked on top of another device because it could cause the device to operate improperly. If such use is necessary, this device and the other device should be observed to verify that they are operating normally. • This device is powered by three AAA batteries. Do not attempt to recharge non-rechargeable batteries as this can cause the batteries to leak or explode. • Do not mix and use different types of batteries together e.g. lithium-ion (Li-ion) and nickel-metal hydride (NiMH) batteries. • Do not mix new and used batteries. • If the device will not be used for an extended period of time, remove batteries before storing the device in a cool and dry place. • This device can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the 04 ENEN 05 hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be done by children without supervision. • Used batteries should be placed in a sealed plastic bag and disposed of safely according to local environmental regulations. Usage Tips • To ensure measurement accuracy, follow the instructions below when you start your measurement: • Place the scale on a flat, hard surface. Soft surfaces such as carpeting will affect the performance of the scale. • Step on the platform with bare feet. Stand still and keep full contact with the electrodes until the measurement is complete. • For the most consistent measurements, weigh yourself at the same time of day and location. • Avoid weighing yourself immediately after strenuous exercise, sitting in the sauna, taking a bath, or drinking and eating. • The condition of the skin on the bottom of your feet can affect the measurement. The natural effects of aging or activity can make this skin hard. Take the reading with clean, slightly damp feet for best accuracy. • Body fat percentage estimates will vary with the amount of water in the body, and can be affected by dehydration or overhydration due to factors such as alcohol consumption, menstruation, illness, intense exercise etc. Notice This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy 06 ENEN 07 and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and recei…

Text truncated - open the document above for the full version.

Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Apr. 18, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AOKB-T9146C [Anker Innovations Limited] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Louis Qi)

Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Apr. 18, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AOKB-T9146C [Anker Innovations Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Louis Qi)

Anker Innovations Limited 2.911(d)(7)USAAgentv1.2 Sect ion 2. 911(d)(7)US A Agent for Serviceof Process Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong 2.9 11(d)(7) USA Desig nated Agent for Servic e of Process We, [Anker Innovations Limit ed ] (“t he applicant”) designate [Power MobileLif e LLC] NOTE1 for the purpose of accepting serviceof processon behalfof the applicant. Applicant co nsent:We Acknowledgeour co nsent to acceptserviceof processin the Unit ed Stat es for mat ters relat ed to the applicableequipment, and at the physicalU. S. addressand email addressof the designated agent and acknowledgeour acceptance of our obligation to maint ain an agent for serviceof processin the Unit ed Stat es for no less than one year af ter eit her the grant ee has permanently terminated all marketing and import at ion of the applicableequipmentwit hin the U. S., or the conclusionof any Commis sion-related administrat ive or judicialproceedinginvolvingthe equipment, whicheveris lat er. Agen t obligati on:We Acknowledgeour obligation to acceptserviceof processin the Unit ed Stat es for mat ters relat ed to the applicableequipmentat our physicalU. S. addressand email addressfor no less than one year af ter eit her the grant ee has permanently terminated all marketing and import at ion of the applicableequipmentwit hin the U. S., or the conclusionof any Com mission-related administrat ive or judicialproceedinginvolvingthe equipment, whicheveris lat er. Applicant Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong GC: 2AOKB Contact Name: Louis.qi Telephone No.: +86-755-86544807 Email:[email protected] USA Agent Company name: Power Mobile Life LLC Address: 10900 NE 8th ST, STE 501, BELLEVUE, WA, 98004, United States FRN: 0033968108 Contact Name: Justin Zhou Telephone No.: 4255373030 Email:[email protected] Signature: Tit le: ComplianceManager Signat ure: Tit le: ComplianceDirec tor Dat e: 2023/ 6/ 30Dat e: 2023/ 6/ 30 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-th e-communications-supply-chain-through-the

Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Agent Authorization Company: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Product Name: Smart Scale C1 Model Number(s): T9146 Product Description: Smart Scale C1 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Apr. 18, 2023 Name: Louis Qi Title: General Manager Company: Anker Innovations Limited

Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Long/Short-term Confidentiality Request Federal Communications Commission Date: Apr. 18, 2023 445 12 th Street SW Washington, DC 20554 FCC ID: 2AOKB-T9146C To Whom it may concerns, Pursuant to sections 0.457(d) and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, we hereby requests long-term confidential treatment of information accompanying this application as outlined below: Schematics Parts List Block Diagram Tune-Up Info Operational Description Antenna Specification FCC_Confidential In addition we hereby request the following exhibits contained in this application to be temporarily (short-term confidentilality) withheld from the public disclosure for an initial period of 180 days until: not applicable External Photos Test Setup Photos Internal Photos Users Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to rule 0.457(d), disclosure of this application and all accompanying documentation will not be made before the date of the GRANT for this application. If you have any questions, please feel free to contact me. Yours sincerely, Signatory Contact person: Louis Qi Title: General Manager

Report No.: AGC01110230365AP03 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC01110230365AP03 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC01110230365AP03 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

Report No.: AGC01110230365AP03 Page 1 of 3 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC01110230365AP03 Page 2 of 3 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC01110230365AP03 Page 3 of 3 INTERNAL VIEW OF EUT (FIGURE 3) ****************************************End of Report************************************* BT Antenna

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2AOKB-T9146C Product Description Smart Scale C1 Model Name T9146 Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Max. Output Power -3.467dBm Antenna Gain 0.8dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [if(GHz)] ≤3.0 for 1-g SAR and ≤7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances < 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT Test Mode Channel Frequency (MHz) Max Output power (dBm) Max Output power (mW) Calculation Value (Note 1) Threshold Value GFSK BLE 2480 -3.467 0.45 0.1413 3.0 Note 1: Calculation Value =[(max. power of channel, mW)/(min. test separation distance, mm)] ·[√f(GHz)]. Fox example: 0.45/5*√2.480=0.1413 ≤ 3.0 According to KDB447498 D01 V06, threshold at which no SAR required is ≤3.0 for 1-g SAR, separation distance is 5mm, and no simultaneous SAR measurement is required. 5. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

CF583BLE SCH V1.0 1 日期 DATE: DATE: DRAWING NO: DATE: A B C D VER: Page: APPROVED BY: Checked By: 页码 版本号 日期 日期 Shenzhen Unique Scales Co., Ltd 深圳市乐福衡器有限公司 A3 A3 A3 TITLE: Drawn By: 批准 审核 制图 名称 文件编号 ble lb kg st G F E D C B A 1 H3H2 4 32 Weight Circuit Body Fat Circuit Power Isolation Circuit MCU Circuit Mcu Program Point LVD Circuit BLE Circuit AAA*3=4.5V BLE Program Point：BOOT、TXB、RXB、VDDB、GNDB JLINK Point：TCK、TMS、VDDB、GNDB Unit Circuit Dong Haiou LED Top layer H2 LB BLE ST kg 1234 H3 1 2 3 S- 1 2 3 E+ 1 2 3 E- 1 2 3 S+ C1 225 C0603 C3 106 C0603 LI D2 WE05DF-BN D0402 R3 200R R0402 LV D3 WE05DF-BN D0402 R4 200R R0402 RI D4 WE05DF-BN D0402 R5 200R R0402 RV D5 WE05DF-BN D0402 R6 200R R0402 D1 WE05DF-BN D0402 VDD GND PA2 PA0 R1 2.2M R0402 R2 1M R0402 F1 0R L3 L0603 102 1 GPIO01/TMS 2 GPIO00/TCK 3 GPIO04/BOOT 4 GPIO05/TX 5 GPIO06/RX 6 X T A L N 7 X T A L P 8 R F P 9 C H G _ O N 1 0 V B A T _ C H G 11 VBUS 12 VBAT 13 DVDD 14 GPIO02 15 GPIO03 1 6 G P I O 0 7 1 7 G P I O 0 8 1 8 G P I O 0 9 1 9 G P I O 1 0 2 0 G P I O 1 1 2 1 G N D U3 OM6621DB OSC1 G1 OSC2 G2 Y1 32MHz OSC3225 C14 NC C0402 C15 NC C0402 C17 4.7PF C0402 C16 0.5pf C0402 C18 NC C0402 C23 105 C0402 C19 106 C0603 C20 104 C0402 D7 WE05DF-BN D0402 C21 475 C0603 C22 104 C0402 R13 10R R0402 R12 10R R0402 R11 10R R0402 BOOT GNDB TXB RXB VDDBTCK TMS 4_5V+ 4_5V- E1 K1 R20 200R R0402 D6 WE05DF-BN D0402 L2 L0603 102 KEY 1 VOREG/VREFP 2 AVSS/VREFN 3 VCM 4 AN0 5 AN1 6 AN2 7 AN3 8 RFC 9 CP0N 10 TO 11 FVR 12 FIR 1 3 R F 2 1 4 R F 1 1 5 F I L 1 6 F V L 1 7 R F 1 8 S I N 2 3 P C 7 2 4 P C 6 25 PD3/TX 26 PD2/RX 27 PC4/SCSA 28 PB2/SCS/SCKA 29 PC5/SDOA/TX 30 PB3/SDO/SDIA/RX 31 PD1 32 PD0 33 PC3/PTCK2 34 PC2/PTP2/PTP2I 35 PC1/PTCK1 36 PC0 3 7 P B 1 / I N T 1 / S T P B 3 8 P B 0 / S C K / S C L 3 9 P A 7 / S D I / S D A / P T C K 2 4 0 P A 6 / R X / S D I A / S T C K 4 1 P A 5 / T X / S C K A / S T P / S T P I 4 2 P A 4 / O S C 1 / S C S A / P T P 2 / P T P 2 I 4 3 P A 3 / O S C 2 / S D O A / P T P 1 / P T P 1 L 4 4 P A 1 / I N T 0 / L V I N / P T P 0 B / S T C K 4 5 V S S 4 6 P A 0 / X T 1 / P T P 0 / P T P 0 1 / O C D S D A / I C P D A 4 7 P A 2 / X T 2 / P T C K 0 / O D C D S C K / I C P C K 4 8 V D D / V I N 1 9 P B 7 2 0 P B 6 2 1 P B 5 2 2 P B 4 U2 BH66F2650 2 VOUT 3 VIN 1 GND U1 SOT23 CE6301A33M C11 104 C0402 C12 105 C0402 C13 104 C0402 R15 1K R16 100K R17 100K R18 33K C24 104 C0402 R19 750R C25 102 C0402 R7 200R R9 1K C10 104 C0402R8 2.7K L1 L0603 102 D8 NC D0402 R14 0R R0603 C5 104 C0603 C2 106 C0603 R10 10R R0402 D1A D0603 D1B D0603 D1C D0603 D1D D0603 D1G D0603 D1E D0603 D1F D0603 D2C D0603 D2D D0603 D2A D0603 D2B D0603 D2F D0603 D2G D0603 D2E D0603 D2H D0603 D3A D0603 D3B D0603 D3C D0603 D3D D0603 D3F D0603 D4A D0603 D3G D0603 D4B D0603 D3E D0603 D4C D0603 D4D D0603 D3H D0603 D5A D0603 D5B D0603 D5C D0603 D4F D0603 D4G D0603 D4E D0603 D5D D0603 C7 102 C0603 C8 102 C0603 C9 102 C0603 C6 105 C0603 L4 L0603 102 C4 104 C0603 VOREG AN1 AN0 FIL FVL FIR FVR BAT+ VDD3.3M PA2 PA0 LVDIN BAT+ TMS BOOT BLE_RX VDD3.3B WAKEUP_MCU BLE_TX MCU_RX MCU_TX TCK BOOT BLE_TX BLE_RX VDD3.3BTCK TMS PA7 VOREG AN0 AN1 FVR FIR VOREG FIL FVL COM1 COM2 COM3 COM4 SEG0 SEG1 VDD3.3M SEG7 SEG6 SEG8 SEG3 SEG5 SEG4 COM2 COM3 COM4 SEG0SEG1SEG2SEG3SEG4 SEG5 SEG6SEG7SEG8 COM1 VDD3.3B VDD3.3M PA2 PA0 WAKEUP_MCU MCU_TX MCU_RX SEG2 LVDINWAKEUP_BLE PA7 WAKEUP_BLE

ProductSpecification P/N: BT Antenna Rev.: A Page: 3 / 6 3 3.4BTVSWR/ReturnLoss/Smith: 3.5BTEfficiencyAndGain: ProductSpecification P/N: BTAntenna Rev.: A Page: 4 / 6 4 3.6.BT3DPattern 2400MHz 2450MHz 2500MHz ProductSpecification P/N: BTAntenna Rev.: A Page: 5 / 6 5 3.7BTEngineeringdrawings： PCBon-boardantenna

Page 1 of 42 FCC Test Report Report No.: AGC01110230365FE02 FCC ID : 2AOKB-T9146C APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Smart Scale C1 BRAND NAME : eufy MODEL NAME : T9146 APPLICANT : Anker Innovations Limited DATE OF ISSUE : Apr. 18, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC01110230365FE02 Page 2 of 42 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr. 18, 2023 Valid Initial Release Report No.: AGC01110230365FE02 Page 3 of 42 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 7 2.4. TEST METHODOLOGY ............................................................................................................................. 7 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 7 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 7 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 8 4. DESCRIPTION OF TEST MODES ................................................................................................................... 9 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 10 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 10 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 10 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 10 6. TEST FACILITY .............................................................................................................................................. 11 7. PEAK OUTPUT POWER ................................................................................................................................ 12 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 13 8. BANDWIDTH .................................................................................................................................................. 15 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 15 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 15 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 15 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 19 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 19 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 19 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 19 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 26 Report No.: AGC01110230365FE02 Page 4 of 42 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 26 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 26 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 26 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 26 11. RADIATED EMISSION ................................................................................................................................. 28 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 28 11.2. TEST SETUP .......................................................................................................................................... 29 11.3. LIMITS AND MEASUREMENT RESULT................................................................................................ 30 11…

Text truncated - open the document above for the full version.

Report No.: AGC01110230365AP02 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC01110230365AP02 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************