2AOV6-MP-132AUNIVERSAL WIRELESS SQUARE CHARGING PAD

UNIVERSAL WIRELESS CHARGER PAD MP-132A INSTRUCTION MANUAL PLEASE READ ALL INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE USE • Remove the product from the box. contents against the list. Package Contents • Universal Wireless Charger Pad • USB cable Key Features • Convenient & fast charging, wireless, hassle free & great looking charging pad cable to phone • Input: 5V/2A, Output: 5V/1A sliding • Keep the product away from heat sources, direct sunlight, humidity, water and any other liquids. • Do not operate the product if it has been exposed to water, moisture or any other liquids to prevent against electric shock, explosion and/or injury to yourself and damage to the product. • Do not use the product if it has been dropped or damaged in any way. • Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs may place the user at serious risk. • Do not use the product with wet hands. • Do not put objects into any of the openings. • Keep the product free from dust, lint etc. • Do not use this product for anything other than its intended use. • Keep the product out of reach of children. • This product is not a toy. INSTRUCTIONS FOR USE • Connect the USB cable (included) to a power outlet rated DC 5V/2A, and the Micro USB plug to the Micro USB input of the Wireless Charging Pad. Red light around the unit will turn on. • Place your Qi Integrated phone on the charging pad, and wireless charging of the phone will start immediately with auto-change of Blue light int ensity around the unit. IMPORTANT: Some phone cases do not support Wireless Charging due to their thickness ble to charge it wirelessly, please remove your phone case and retry. Care and Maintenance will be able to enjoy the product for many years. •Do not expose the Wireless Charging Pad to liquid, moisture or humidity to avoid the product’s internal circuit being affected. • Don’t use abrasive cleaning solvents to clean the device. •Do not expose the device to extremely high or low temperature as this will shorten • Don’t dispose of the device in a fire as it will result in an explosion. •Don’t expose the device t o contact with sharp objects as this will cause scratches and damage. • Don’t let the device fall on the floor. The internal circuit might get damaged. • professional. Input: DC 5V/2A Output: DC 5V/1A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving an tenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Runs low temperature as wired charger • Friendly Blue LED indicators, never overchares your battery or wast energy Suitable for Qi compatible phones like i Phone 11/11 Plus/11 Pro/11 Pro Max, iPhone X / XS / XR / XS Max, iPhone 8/8 Plus, Samsung Galaxy S20/S20 Plus/S20 Ultra, S10/S10 Plus, S9/S9 Plus, S8/S8 Plus, HTC, Nexus and more. •

FCC ID: 2AOV6-MP-132A

Label Location On EUT Label Product Name: UNIVERSAL WIRELESS SQUARE CHARGING PAD Model No.: MP-132A FCC ID: 2AOV6-MP-132A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2AOV6-MP-132A

version01 Shenzhen Minsuo Industrial Co.,Ltd Declaration concerning Antenna Specification It is hereby declared that the product Model No.: MP-132A, WC-12/1171, 16653 FCC ID : 2AOV6-MP-132A fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal antenna type(s) described below: Model No. of antenna: N/A Type of antenna:Inductive loop coil Antenna Gain of the antenna: 0 dBi Frequency range: 110.1-205KHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Shenzhen Minsuo Industrial Co.,Ltd Address: 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China City:Shenzhen ZIP / Postal code: Country:China Place:ShenzhenDate:2020-07-31 Signature:

Report No.: 18220WC00084302FCC ID: 2AOV6-MP-132APage 1 of 13 Code:AB-RF-05-a FCC TEST REPORT Client Name: Shenzhen Minsuo Industrial Co.,Ltd Address: 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China Product Name: UNIVERSAL WIRELESS SQUARE CHARGING PAD Date: Jul. 31, 2020 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC00084302FCC ID: 2AOV6-MP-132APage 2 of 13 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................... 4 1.1. Client Information ....................................................................................................................................... 4 1.2. Description of Device (EUT) ..................................................................................................................... 4 1.3. Auxiliary Equipment Used During Test ................................................................................................... 5 1.4. Test Equipment List .................................................................................................................................... 5 1.5. Measurement Uncertainty ......................................................................................................................... 5 1.6. Description of Test Facility ........................................................................................................................ 5 2. Measurement and Result ..................................................................................................................................... 6 2.1. Requirements .............................................................................................................................................. 6 2.2. Test Setup .................................................................................................................................................... 7 2.3. Test Procedure ............................................................................................................................................ 7 2.4. Test Result ................................................................................................................................................... 7 2.4.1. Equipment Approval Considerations item 5.b of KDB 680106 D01 v03. ...................................... 7 2.4.2. Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(b), 1.1310 .................................................................................................................................................................. 9 APPENDIX I -- TEST SETUP PHOTOGRAPH ................................................................................................... 11 Report No.: 18220WC00084302FCC ID: 2AOV6-MP-132APage 3 of 13 Code:AB-RF-05-a TEST REPORT Applicant: Shenzhen Minsuo Industrial Co.,Ltd Manufacturer: Shenzhen Minsuo Industrial Co.,Ltd Product Name: UNIVERSAL WIRELESS SQUARE CHARGING PAD Model No.: MP-132A, WC-12/1171, 16653 Trade Mark: N.A. Rating(s): Input: DC 5V, 2A Wireless Output: 5W Max Test Standard(s) : FCC Part 1.1310, 1.1307(b) Test Method(s): KDB680106 D01 RF Exposure Wireless Charging Apps v03 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also,this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 1.1307 & KDB680106 D01 requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of ReceiptJun. 29, 2020 Date of TestJun. 29~Jul. 17, 2020 Prepared By (Engineer / Dolly Mo) Reviewer (Supervisor / Bibo Zhang) Approved & Authorized Signer (Manager / Tom Chen) Report No.: 18220WC00084302FCC ID: 2AOV6-MP-132APage 4 of 13 Code:AB-RF-05-a 1. General Information 1.1. Client Information 1.2. Description of Device (EUT) Product Name : UNIVERSAL WIRELESS SQUARE CHARGING PAD Model No.: MP-132A, WC-12/1171, 16653 (Note: All samples are the same except the appearance color, so we prepare "MP-132A" for test only.) Trade Mark: N.A. Test Power Supply: AC 120V, 60Hz for adapter Test Sample No.: 1-2-1(Normal Sample), 1-2-1(Engineering Sample) Product Description : Operation Frequency:110.1-205KHz Modulation Type:FSK Antenna Type:Inductive loop coil Antenna Antenna Gain(Peak):0 dBi Remark:1) For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. Applicant: Shenzhen Minsuo Industrial Co.,Ltd Address: 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China Manufacturer: Shenzhen Minsuo Industrial Co.,Ltd Address : 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China Factory: Shenzhen Minsuo Industrial Co.,Ltd Address : 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China Report No.: 18220WC00084302FCC ID: 2AOV6-MP-132APage 5 of 13 Code:AB-RF-05-a 1.3. Auxiliary Equipment Used During Test Adapter: Manufacturer: ZTE M/N: STC-A2050I1000USBA-C S/N: 201202102100876 Input: 100-240V~ 50/60Hz, 0.3A Output: DC 5V, 2000mA Mobile Phone:iPhone8 1.4. Test Equipment List ItemEquipmentManufacturerModel No.Serial No.Last Cal.Cal. Interval 1 Magnetic field meter NARDAELT-400423623 Dec. 23, 2019 1 Year 2E-Field ProbeNardaEF0391Q15221 Nov.17, 2017 3 Year 3H-Fi…

Text truncated - open the document above for the full version.

Report No.: 18220WC00084301FCC ID: 2AOV6-MP-132APage 1 of 30 Code:AB-RF-05-a FCC TEST REPORT Client Name: Shenzhen Minsuo Industrial Co.,Ltd Address: 12th floor, Block B, Tengyao Building, No. 268 Gushu 2nd road,Xixiang Town, Bao'an, Shenzhen, Guangdong, China Product Name: UNIVERSAL WIRELESS SQUARE CHARGING PAD Date: Jul. 31, 2020 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC00084301FCC ID: 2AOV6-MP-132APage 2 of 30 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................... 4 1.1. Client Information ....................................................................................................................................... 4 1.2. Description of Device (EUT) ..................................................................................................................... 4 1.3. Auxiliary Equipment Used During Test ................................................................................................... 5 1.4. Description of Test Modes ........................................................................................................................ 5 1.5. Description Of Test Setup ......................................................................................................................... 6 1.6. Test Equipment List .................................................................................................................................... 7 1.7. Measurement Uncertainty ......................................................................................................................... 8 1.8. Description of Test Facility ........................................................................................................................ 8 2. Summary of Test Results ..................................................................................................................................... 9 3. Conducted Emission Test ................................................................................................................................... 10 3.1. Test Standard and Limit .......................................................................................................................... 10 3.2. Test Setup .................................................................................................................................................. 10 3.3. Test Procedure .......................................................................................................................................... 10 3.4. Test Data .................................................................................................................................................... 10 4. Radiation Spurious Emission and Band Edge ................................................................................................ 15 4.1. Test Standard and Limit .......................................................................................................................... 15 4.2. Test Setup .................................................................................................................................................. 15 4.3. Test Procedure .......................................................................................................................................... 16 4.4. Test Data .................................................................................................................................................... 17 5. Antenna Requirement ......................................................................................................................................... 21 5.1. Test Standard and Requirement ............................................................................................................ 21 5.2. Antenna Connected Construction .......................................................................................................... 21 APPENDIX I -- TEST SETUP PHOTOGRAPH ................................................................................................... 22 APPENDIX II -- EXTERNAL PHOTOGRAPH ..................................................................................................... 24 APPENDIX III -- INTERNAL PHOTOGRAPH ..................................................................................................... 28 Report No.: 18220WC00084301FCC ID: 2AOV6-MP-132APage 3 of 30 Code:AB-RF-05-a TEST REPORT Applicant: Shenzhen Minsuo Industrial Co.,Ltd Manufacturer: Shenzhen Minsuo Industrial Co.,Ltd Product Name: UNIVERSAL WIRELESS SQUARE CHARGING PAD Model No.: MP-132A, WC-12/1171, 16653 Trade Mark: N.A. Rating(s): Input: DC 5V, 2A Wireless Output: 5W Max Test Standard(s) : FCC Part15 Subpart C 2019, Paragraph 15.209 Test Method(s): ANSI C63.10: 2013 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also,this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of ReceiptJun. 29, 2020 Date of TestJun. 29~Jul. 17, 2020 Prepared By (Engineer / Dolly Mo) Reviewer (Supervisor / Bibo Zhang) Approved & Authorized Signer (Manager / Tom Chen) Report No.: 18220WC00084301FCC ID: 2AOV6-MP-132APage 4 of 30 Code:AB-RF-05-a 1. General Information 1.1. Client Information Applicant: …

Text truncated - open the document above for the full version.

FCC ID: 2AOV6-MP-132A Photo of Conducted Emission Measurement Photo of Radiation Emission Test Photo of MPE Measurement