2APQD-F153-in-1 Wireless Charger

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

- Shenzhen Aodehong Electronic Technology Co.,Ltd - Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 6/21/2024 U.S. Agent Designation Shenzhen Aodehong Electronic Technology Co.,Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2APQD-F15): Name and company of U.S. agent: UUX GROUP INC Physical U.S. address of agent: 36 South 18th Avenue, Suite A Brighton, CO USA 80601 FRN of U.S. agent: 0033701590 Email address of U.S. agent: [email protected] UUX GROUP INC acknowledges their obligation to accept service of process on behalf of Shenzhen Aodehong Electronic Technology Co.,Ltd. Shenzhen Aodehong Electronic Technology Co.,Ltd with the FRN 0027497569 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Tina Fang Manager Shenzhen Aodehong Electronic Technology Co.,Ltd Signature Jack Fu Manager UUX GROUP INC 48_[model] US_Agent_ 2.911(d)(7) - U, V05

Page 1 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details External EUT Photo Photo 1 Photo 2 Page 2 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Page 5 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 Photo 10 Page 6 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 11 Photo 12 Page 7 of 7 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 13 Photo 14 ---The End---

Label Size: L45mm * W20mm 1. The label is silk-screen on the sample 3-in-1 Wireless Charger Model Name: F15 FCC ID: 2APQD-F15 L W

Page 1 of 5 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details Internal EUT Photo Photo 1 Photo 2 Page 2 of 5 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Phone Coil Page 3 of 5 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Watch Coil Page 4 of 5 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Earphone Coil Page 5 of 5 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 ------End------

Page 1 of 18 Report No.: AITSZ24052905W2 RF Exposure Evaluation Client Information: Applicant: Shenzhen Aodehong Electronic Technology Co.,Ltd. Applicant add.: Room 501, Building 2, Gaoya industrial park, No. 8 Liuhe Road, Liuyue,Henggang Street, Longgang District, Shenzhen City, Guangdong Province, China. Manufacturer: Shenzhen Aodehong Electronic Technology Co.,Ltd. Manufacturer add.: Room 501, Building 2, Gaoya industrial park, No. 8 Liuhe Road, Liuyue,Henggang Street, Longgang District, Shenzhen City, Guangdong Province, China. Product Information: Product Name: 3-in-1 Wireless Charger Model No.: F15 Brand Name: NEWQI Test samples.: AITSZ24052905-1 FCC ID: 2APQD-F15 Applicable standards: FCC CFR 47 PART 1, § 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: Jun. 06, 2024 Date of Test: Jun. 06, 2024 ~ Jun. 18, 2024 Date of Issue: Jun. 18, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean She Page 2 of 18 Report No.: AITSZ24052905W2 1 CONTENTS COVER PAGE Page 1 CONTENTS 2 2 TEST FACILITY 4 2.1 Deviation from standard 4 2.2 Abnormalities from standard conditions 4 2.3 Test Location 4 3 GENERAL INFORMATION 5 4 TEST METHODOLOGY 6 4.1 Measuring Standard 6 4.2 Requirements 6 4.3 Limits 6 4.4 Test Setup 7 4.5 Test Procedure 7 5 Equipment Approval Considerations 8 5.1 Description of the test mode 9 5.2 Peripheral List 9 5.3 Test Instruments list 9 5.4 Duty Cycle 10 5.5 Test Result 12 5.6 Test Setup photo 16 Page 3 of 18 Report No.: AITSZ24052905W2 Revision History Revision Issue Date Revisions Revised By 00 Jun. 18, 2024 Initial Issue Sean She Page 4 of 18 Report No.: AITSZ24052905W2 2 TEST FACILITY The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC —Registration No.: 31737 CAB identifier: CN0165 The 3m Semi-anechoic chamber of Guangdong Asia Hongke Test Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 31737 A2LA-Lab Cert. No.: 7133.01 Guangdong Asia Hongke Test Technology Limited has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. 2.1 Deviation from standard None 2.2 Abnormalities from standard conditions None 2.3 Test Location Guangdong Asia Hongke Test Technology Limited Address: B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Page 5 of 18 Report No.: AITSZ24052905W2 3 GENERAL INFORMATION EUT Name: 3-in-1 Wireless Charger Model No: F15 Serial Model: N/A Test sample(s) ID: AITSZ24052905-1 Sample(s) Status: Engineer sample Operation frequency: Coil1: For Phone: 113kHz-205kHz Coil2: For Earphone: 113kHz-205kHz Coil3: Watch: 300kHz-350kHz Modulation Technology: ASK Antenna Type: Coil1/Coil2/Coil3: Loop coil Antenna Antenna gain: Coil1/Coil2/Coil3: 0dBi Hardware version.: N/A Software version.: N/A Power supply: Input: 5V⎓3A/9V⎓3A/12V⎓2.5A Output: 5V⎓1A/9V⎓1.1A/9V⎓1.66A Model different: color varies Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 6 of 18 Report No.: AITSZ24052905W2 4 TEST METHODOLOGY 4.1 Measuring Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. According KDB680106 D01: KDB 680106 D01 Wireless Power Transfer v04. 4.2 Requirements According to the item 3 of KDB 680106 D01v04: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Mobile Device and Portable Device Configurations (2) Equipment Authorization Procedures for Devices Operating at Frequencies Below 4 MHz (3) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the top surface. 4.3 Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Page 7 of 18 Report No.: AITSZ24052905W2 4.4 Test Setup 4.5 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger…

Text truncated - open the document above for the full version.

Page 1 of 25 Report No.: AITSZ24052905W1 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. FCC TEST REPORT Client Information: Applicant: Shenzhen Aodehong Electronic Technology Co.,Ltd. Applicant add.: Room 501, Building 2, Gaoya industrial park, No. 8 Liuhe Road, Liuyue,Henggang Street, Longgang District, Shenzhen City, Guangdong Province, China. Manufacturer: Shenzhen Aodehong Electronic Technology Co.,Ltd. Manufacturer add.: Room 501, Building 2, Gaoya industrial park, No. 8 Liuhe Road, Liuyue,Henggang Street, Longgang District, Shenzhen City, Guangdong Province, China. Product Information: Product Name: 3-in-1 Wireless Charger Model No.: F15 Brand Name: NEWQI FCC ID: 2APQD-F15 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: Jun. 06, 2024 Date of Test: Jun. 06, 2024 ~ Jun. 18, 2024 Date of Issue: Jun. 18, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean She Page 2 of 25 Report No.: AITSZ24052905W1 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS .................................................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 5 2.1 STATEMENT OF THE MEASUREMENT UNCERTAINTY ......................................................................................... 5 2.2 MEASUREMENT UNCERTAINTY ...................................................................................................................... 5 3 TEST FACILITY .............................................................................................................................................. 6 3.1 DEVIATION FROM STANDARD ......................................................................................................................... 6 3.2 ABNORMALITIES FROM STANDARD CONDITIONS ............................................................................................... 6 3.3 TEST LOCATION .......................................................................................................................................... 6 4 GENERAL INFORMATION ............................................................................................................................. 7 4.1 EUT TEST MODE ........................................................................................................................................ 8 4.2 DESCRIPTION OF TEST SETUP ....................................................................................................................... 8 4.3 PERIPHERAL LIST ........................................................................................................................................ 9 4.4 EUT PERIPHERAL LIST ................................................................................................................................ 9 5 EQUIPMENTS LIST FOR ALL TEST ITEMS ................................................................................................. 10 6 CONDUCTED EMISSION TEST.................................................................................................................... 11 6.1 CONDUCTED EMISSION MEASUREMENT............................................................................................ 11 6.2 POWER LINE CONDUCTED EMISSION LIMITS ....................................................................................... 11 6.3 TEST PROCEDURE ............................................................................................................................... 11 6.4 DEVIATION FROM TEST STANDARD .................................................................................................... 11 6.5 TEST SETUP .......................................................................................................................................... 12 6.6 EUT OPERATING CONDITIONS ............................................................................................................ 12 6.7 TEST RESULT ........................................................................................................................................... 13 7 RADIATED EMISSION MEASUREMENT ..................................................................................................... 15 7.1 RADIATED EMISSION LIMITS ........................................................................................................................ 15 7.2 ANECHOIC CHAMBER TEST SETUP DIAGRAM ................................................................................................ 16 7.3 TEST PROCEDURE ....................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 3 承 認 書 SPECIFICATION FOR APPROVAL 客 戶： CUSTOMER: 澳德鸿 客 戶 料 號： CUST P/N: EXQ-40MM0000 松 岛 料 號： FINE P/N: G4011-6.5UH 单线圈unicoil 0.08*24*2P*10TS 産 品 型 號： DESC: Φ40MMX5.0MMX0.5MM单槽single groove 日 期： DATE: 2022/06/07 版 本： Version: A.0 擬制 PREPARED BY 審核 CHECKED BY 批准 APPROVED BY 客戶承認 CUSTOMER APPROVE 黄燕铭 宁元安 黄锦华 深圳市松岛科技有限公司 工廠地址：东莞市东坑镇骏发三路123号三甲高新技术产业园2栋8楼 TEL：13728755750 FAX：0755-84526500 E-mail：[email protected] Page 2 of 3 版本變更履歷 Version Change History 版本 Rev. 變 更 前 Before Change 變 更 後 After Change 更 改 日 期 Change Date 批 准 Approved By A.0 新发行 ---- 2018/03/09 黄锦华 Page 3 of 3 SPECIFICATION 産 品 型 號： DESC Φ20.5x38.5-6.5uH-0.08x24*2P-15mm 版本 Rev：A.0 客戶CUST: XXX 客户料号CUST P/N: 一、尺寸DIMENSION:(mm) 二、原理图SCHEMATIC DIAGRAM: A 40.0±0.5 B 38.5±0.5 C 20.5±0.5 D 30±2 E 4±2 Note: 1.Cross out wire; 2.Wrap 8mm (ref) width high-temperature adhesive paper 1-2Ts around the outlet position 3. The coil is attached to the circular hard magnetic disc with groove, the magnetic disc size is 40±0.5mm, the inner hole is 5.3mm, and the thickness is 0.5±0.2mm. 三、绕线参数Winding Specification: 序号 NO. 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 Winding Direction 1 S F 漆包线0.08*24*2P 10Ts CCW 四、电气特性ELECTRICAL CHARACTERISTICS: 温度TEMPERATURE:25±10°C, 湿度RELATIVE HUMIDITY:65±20% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1 IND. S-F 3.8 uH ±20%单独线圈 100KHz/1.0V LCZ METER 1062B 2 IND. S-F 6.5uH ±10%加磁片 100KHz/1.0V LCZ METER 1062B 3 DCR S-F ≤80mΩ 100KHz/1.0V LCZ METER 502B 4 Q S-F ≥37 100KHz/1.0V LCZ METER 502B 擬制/日期PREPARED BY/DATE 審核/日期CHECKED BY/DATE 黄燕铭2022/06/07 黄锦华2022/06/07

样品承认书 客户名称 ：深圳市澳德鸿电子有限公司 客户料号 :EXQ-40MM00002 物料名称 : 无线充发射线圈 品牌名称: 捷利通科技 规格型号 :T40*5.0*0.5 6.5uH 10% 版 本 ：1 生产批号/料号 ： 送样日期 ：2022-01-22 签样日期 ： 客户承认： 供应商承认： 采购部 工程部 审核 批注 拟定 审核 批准 陈翠珠 李书坡 张军 customer name Customer Material Number name of material brand name specifications and models versions Production lot/material number datelanded Sample signing date Customer recognition Supplier recognition purchasing departmentÿ engineering department audit annotation protocol audit ratify sample approval sheet Wireless charging transmitter coil Initial release AO 新版本制订 2021-07-05 版本 VersionContents 修改内容修订日期 DateNO 序号 Update history 更新履历 ཆරቪረ অսPP 䙐୶ࡦ ༷⌘ රਧ㿴Ṭ 䘲⭘ᵪරӗ૱਽〠 สᵜ㿴Ṭ 40*5.0*0.5 ITEM A B C D E F SPEC. 20±0.5 38±0.5 40±0.5 2±2 30±2 2.0max 0.5 38 Wireless charging transmitter coil 5.3 DCR: 70 m max （以圈数为准）。 5.2 电感量:L=6.5uH 10% at 100khz,1v; 5.1 测试条件:环境湿度:65+20% 环境温度:25+5 C 5.电性能参数 4 10 Ts21 绕线方式 0.08*24*2PN1 匝数 包胶圈数 尾点 起点 线规绕组 N0 3 2 1 4.绕制工艺 1 2 3.原理图 5.4 Max Current: 2.0A 5.5 Q值：70（min） 6 5 5 5 3 2 1 六.Construction 4 NO Material Name 1 背胶 2 铁氧体片 3 线圈 4 5 胶水 6 固定胶纸 Adhesive ferrite sheet coil glue Fixed adhesive paper

客户名称 ：深圳市澳德鸿电子有限公司 客户料号: 物料名称 : 无线充发射线圈 品牌名称 : 捷利通科技 规格型号 :T25*23*2.6 8.1uH 10% 版 本 ：1 生产批号/料号： 送样日期 ：2022-04-28 签样日期 ： 客户承认： 供应商承认： 采购部 工程部 审核 批注 拟定 审核 批准 陈翠珠 李书坡 张军 EXQ-APPLE0001 customer name Customer Material Number name of material brand name specifications and models versions Production lot/material number datelanded Sample signing date Wireless charging transmitter coil Customer recognition Supplier recognition purchasing departmenty engineering department audit annotation audit protocolratify sample approval sheet Initial release AO 新版本制订 2021-07-05 版本 VersionContents 修改内容修订日期 DateNO 序号 Update history 更新履历 ཆරቪረ অսPP 䙐୶ࡦ༷⌘රਧ㿴Ṭ䘲⭘ᵪරӗ૱਽〠 สᵜ㿴Ṭ 25*23*2.7 Wireless charging transmitter coil NO product name type specification applicable models manufacturer remark Basic specification external dimension 5.3 DCR: 70 m max （以圈数为准）。 5.2 电感量:L=8.1uH 10% at 100khz,1v; 5.1 测试条件:环境湿度:65+20% 环境温度:25+5 C 5.电性能参数 4 14 Ts21 绕线方式 2UEW-0.08*24PN1 匝数 包胶圈数 尾点 起点线规绕组 N0 3 2 1 4.绕制工艺 1 2 3.原理图 5.4 Max Current: 2.0A 5.5 Q值：27（min） schematic diagram Winding process Electrical property parameter 5.1 Test conditions: Ambient humidity: 65+20% Ambient temperature: 25+5°C 5.2 Inductance: L=8.1uH± 10%at 100khz, 1v; (based on the number of turns) 5.3 DCR:70Mÿmax 5.4 Max Current: 2.0A 5.5 Q value 27 (min) 六.Construction NO Material Name 1 背胶 2 铁氧体片 3 线圈 4 背胶 5 6 固定胶纸 Adhesive ferrite sheet coil application of gum Fixed adhesive paper

Page 1 of 2 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Test Setup Photo DCD Conduction Radiation (9KHz-30MHz) Page 2 of 2 FCC ID: 2APQD-F15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Radiation (30MHz-1000MHz) ------End------