2APQIITAFSRSMTSmart Climate ControllerSLR

1 Smart Climate Controller (SLR) (Wall Mount) FCC ID: 2APQIITAFSRSMT IC: 30370-ITAFSRSMT UL Part Numbers: IT-AF-SLR-SMT IT-AF-SLR-SMT Overview This document summarizes the introduction of the climate controller thermostat IT-AF-SLR-SMT (Fig.1). IT-AF-SLR-SMT is a solar powered, environmentally friendly, and energy-saving smart product for fans that help save on HVAC systems. Powered by solar energy and the power grid, with priority given to utilizing solar energy. IT-AF-SLR-SMT enables users to remotely control multiple different models of solar fans through Android & iOS apps via Bluetooth distribution network (Fig.2). (Fig.1) Specifications (Fig. 2) Warning: - Disconnect power at the circuit breaker before installing or servicing - Use wires rated at least 105 °C – copper only - Installation/wiring must be in accordance with national and local code regulations - Keep the enclosure cover closed at all times when not servicing. - Cover all unused wires with a wire connector FCC Regulations FCC Supplier’s Declaration of Conformity Product Name: Smart Climate Controller (SLR) Model number: IT-AF-SLR-SMT FCC ID: 2APQIITAFSRSMT IC: 30370-ITAFSRSMT UL Part Number: IT-AF-SLR-SMT Suppliers Name: QC Manufacturing Inc. Suppliers Address (USA): 26040 Ynez rd. Temecula, California 92591, United States Suppliers Website: www.QuietCoolSystems.com Contact Email/Telephone: Jeff Whitehouse [email protected] 2 ISED Warning statements in User Manual This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)L’appareil ne doit pas produire de brouillage;(2)L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil ettoutes les personnes. FCC Warning statements in User Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. 3 Installation Instruction Ensure to turn off the main power of the adapter before wiring. Installation can only be completed by qualified personnel. Install the adapter, controller, solar panel, and fan according to the product specifications (Fig.2) and wiring diagram (Fig.3). (Fig.3) Unscrew the screws securing the cover and flip it upwards as shown in Fig.4. Once the cover is open, We can see the label as shown in Fig.5 (Fig. 4) (Fig. 5) Product Label Color specifications of wires inside the control box (Fig. 4 ) . The A/B/C ports of the control box are all aviation plug interfaces. Control box A, connected to the DC power output terminal of the adapter. Control box B connects to the solar panel. Control box C connects to the fan. Once wiring is completed, close the cover and tighten the screw. Caution: When inserting the aviation plug into the male/female socket, the positive/negative terminals should not be reversed. Note: When using an aviation plug, the male and female terminals must be inserted together, and the positive and negative terminals must not be reversed. 4 Panel operation for thermostat (1) After powering on, first reset the distribution network operation, that is, reset the switch (reset Bluetooth connection): Press the "+" and "-" buttons on the panel simultaneously for 5 seconds, and the screen will display "Reset...", When successful, display " " and restore the initial state value (Fig. 6 ). (2) The default dis…

Text truncated - open the document above for the full version.

QC Manufacturing Inc. Date: 4/8/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(5) Attestation FCC ID: 2APQIITAFSRSMT Grantee FRN: 0027498658 1. QC Manufacturing Inc. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. QC Manufacturing Inc. certifies that, the device does not have cybersecurity and / or anti- virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered List installed on the device, nor will it be installed by the applicant anytime after certification. 3. QC Manufacturing Inc. certifies that the RF device is not a router “produced in a foreign country”. 4. QC Manufacturing Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Jeff Whitehouse Job Title: Director of Purchasing Company Name: QC Manufacturing Inc.

QC Manufacturing Inc. Date: 3/6/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: 2APQIITAFSRSMT Grantee FRN: 0027498658 To whom it may concern: QC Manufacturing Inc. (“the applicant”) as required by section §2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. Contact Person: Jeff Whitehouse Company Name: QC Manufacturing Inc. FCC FRN: 0027498658 Company US Address: 26040 Ynez rd, Temecula, CA 92591, United States Email: [email protected] Sincerely yours, Name: Jeff Whitehouse Job Title: Director of Purchasing Company Name: QC Manufacturing Inc.

QC Manufacturing Inc. Date: 3/6/2026 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: QC Manufacturing Inc. Contact Name: Jeff Whitehouse Title of Person: Director of Purchasing Address: 26040 Ynez rd, Temecula, CA 92591, United States

QC Manufacturing Inc. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2APQIITAFSRSMT To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Bom list Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: QC Manufacturing Inc. Contact Name: Jeff Whitehouse Title of Person: Director of Purchasing Address: 26040 Ynez rd. Temecula, California 92591, United States Date:3/6/2026

External Photographs Page 2 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-1 View of EUT-2 Page 3 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-3 View of EUT-4 Page 4 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-5

Model: IT-AF-SLR-SMT Name: Smart Climate Controller(SLR) INPUT 22V / 2.04A 24V / 2.5A 20.5V / 1.5A 25W 40W / 45W 65W SOLAR PANEL & FAN IT-AF-SLR-SMT FCC ID: 2APQIITAFSRSMT IC: 30370-ITAFSRSMT 1.middle shell Model label Model barcode label Date barcode label IT-AF-SLR-SMT Note: The label will be permanently attached to the product

Internal Photographs Page 2 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-1 Internal View of EUT-2 Page 3 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-3 Internal View of EUT-4 433.92MHz Antenna Page 4 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-5 Internal View of EUT-6 BLE/WIFI Antenna Page 5 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-7 Internal View of EUT-8 Page 6 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-9

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. FCC RF EXPOSURE REPORT For Smart Climate Controller(SLR) MODEL NUMBER: IT-AF-SLR-SMT FCC ID: 2APQIITAFSRSMT REPORT NUMBER: 4792046814-1-RF-4 ISSUE DATE: April 1, 2026 Prepared for QC Manufacturing Inc. 26040 Ynez rd. Temecula, California 92591, United States Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4792046814-1-RF-4 Page 2 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 April 1, 2026 Initial Issue REPORT NO.: 4792046814-1-RF-4 Page 3 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. REQUIREMENT ................................................................................................................. 6 REPORT NO.: 4792046814-1-RF-4 Page 4 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: QC Manufacturing Inc. Address: 26040 Ynez rd. Temecula, California 92591, United States Manufacturer Information Company Name: Shenzhen Asia Bright Co.,Ltd. Address: 2nd and 3rd Floor Building E, North Area, No.2 of Shangxue Science Park,Bantian, Shenzhen, China EUT Information EUT Name: Smart Climate Controller(SLR) Model: IT-AF-SLR-SMT Sample Received Date: February 11, 2026 Sample Status: Normal Sample ID: 9441011 Date of Tested: March 9, 2026 to April 1, 2026 APPLICABLE STANDARDS STANDARD TEST RESULTS 447498 D04 Interim General RF Exposure Guidance v01 PASS Prepared By: Checked By: Fanny Huang Kebo Zhang Project Engineer Operations Leader Approved By: Stephen Guo Operations Manager REPORT NO.: 4792046814-1-RF-4 Page 5 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with 47 CFR FCC Part 1 Subpart I, section 1.1307 and KDB 447498 D04 Interim General RF Exposure Guidance v01. 3. FACILITIES AND ACCREDITATION Accreditation Certificate A2LA (Certificate No.: 4102.01) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with A2LA. FCC (FCC Designation No.: CN1187) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. Has been recognized to perform compliance testing on equipment subject to the Commission's Declaration of Conformity (DoC) and Certification rules. ISED (Company No.: 21320) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been registered and fully described in a report filed with ISED. The Company Number is 21320 and the test lab Conformity Assessment Body Identifier (CABID) is CN0046. VCCI (Registration No.: C-20202, G-20240, R-20248 and T-20202) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with VCCI, the Membership No. is 3793. Facility Name: Chamber E, the VCCI registration No. is G-20240 and R-20248 Shielding Room F, the VCCI registration No. is C-20202 and T-20202 Note 1: All tests measurement facilities use to collect the measurement data are located at Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China. Note 2: The test anechoic chamber in UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch had been calibrated and compared to the open field sites and the test anechoic chamber is shown to be equivalent to or worst case from the open field site. Note 3: For below 30 MHz, lab had performed measurements at test anechoic chamber and comparing to measurements obtained on an open field site. And these measurements below 30 MHz had been correlated to measurements performed on an OFS. REPORT NO.: 4792046814-1-RF-4 Page 6 of 7 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No.: 10-SL-F0112 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 4. REQUIREMENT LIMIT AND CALCULATION METHOD According to 447498 D04 Interim General RF Exposure Guidance v01, 2.1.4 MPE-Based Exemption An alternative to the SAR-based exemption is provided in § 1.1307(b)(3)(i)(C), for a much wider frequency range, from 300 kHz to 100 GHz, applicable for separation distances greater or equal to λ/2π, where λ is the f…

Text truncated - open the document above for the full version.

unit :mm ∅ 3*10 Black heat shrink tube 22 5±5mm, RED 80 3 Tin liquid Antenna gain：-4.15 dBi Antenna type: Line antenna

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C ISED RSS-210 ISSUE 11 CERTIFICATION TEST REPORT For Smart Climate Controller(SLR) MODEL NUMBER: IT-AF-SLR-SMT REPORT NUMBER: 4792046814-1-RF-3 ISSUE DATE: April 1, 2026 FCC ID: 2APQIITAFSRSMT IC: 30370-ITAFSRSMT Prepared for QC Manufacturing Inc. 26040 Ynez rd. Temecula, California 92591, United States Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4792046814-1-RF-3 Page 2 of 38 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0057 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 April 1, 2026 Initial Issue REPORT NO.: 4792046814-1-RF-3 Page 3 of 38 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0057 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Clause Test Items FCC Rules Test Results 1 Transmitter Timeout CFR 47 FCC §15.231 (a) (1) ISED RSS-210 Annex A.1.2 Pass 2 20 dB Bandwidth and 99 % Occupied Bandwidth CFR 47 FCC §15.231 (c) ISED RSS-210 Annex A.1.4 Pass 3 Radiated Emission CFR 47 FCC §15.231 (b)(e) CFR 47 FCC §15.205 and §15.209 RSS-210 Annex A.1.3 RSS-GEN Clause 8.9 RSS-GEN Clause 8.10 Pass 4 AC Power Line Conducted Emission ANSI C63.10-2013, Clause 6.2 Pass 5 Antenna Requirement CFR 47 FCC §15.203 ISED RSS-Gen Clause 6.3 Pass Note 1: This test report is only published to and used by the applicant, and it is not for evidence purpose in China. Note 2: The measurement result for the sample received is <Pass> according to < CFR 47 FCC PART 15 SUBPART C and ISED RSS-210 ISSUE 11> when <Accuracy Method> decision rule is applied. REPORT NO.: 4792046814-1-RF-3 Page 4 of 38 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0057 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. CALIBRATION AND UNCERTAINTY ................................................................................ 7 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................. 7 4.2. MEASUREMENT UNCERTAINTY .............................................................................. 7 5. EQUIPMENT UNDER TEST ............................................................................................... 8 5.1. DESCRIPTION OF EUT ............................................................................................. 8 5.2. MAXIMUM FIELD STRENGTH ................................................................................... 8 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................. 8 5.4. TEST ENVIRONMENT ............................................................................................... 8 5.5. DESCRIPTION OF TEST SETUP .............................................................................. 9 5.6. MEASURING INSTRUMENT AND SOFTWARE USED ............................................10 6. ANTENNA PORT TEST RESULTS ...................................................................................11 6.1. ON TIME AND DUTY CYCLE ....................................................................................11 6.2. TRANSMITTER TIMEOUT ........................................................................................13 6.3. 20 dB BANDWIDTH AND 99 % OCCUPIED BANDWIDTH .......................................16 6.4. RADIATED TEST RESULTS .....................................................................................19 6.4.1. FIELD STRENGTH OF INTENTIONAL EMISSIONS .........................................26 6.4.2. SPURIOUS EMISSIONS BELOW 1 GHz AND ABOVE 30 MHz ........................28 6.4.3. SPURIOUS EMISSIONS ABOVE 1 GHz ...........................................................30 6.4.4. SPURIOUS EMISSIONS BELOW 30 MHz.........................................................32 7. AC POWER LINE CONDUCTED EMISSION ....................................................................35 8. ANTENNA REQUIREMENTS ............................................................................................38 REPORT NO.: 4792046814-1-RF-3 Page 5 of 38 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO.: 10-SL-F0057 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: QC Manufacturing Inc. Address: 26040 Ynez rd. Temecula, California 92591, United States Manufacturer Information Company Name: Shenzhen Asia Bright Co.,Ltd. Address: 2nd and 3rd Floor Building E, North Area, No.2 of Shangxue Science Park,Bantian, Shenzhen, China EUT Information EU…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) MEASUREMENT POSITION (X axis) MEASUREMENT POSITION (Y axis) MEASUREMENT POSITION (Z axis) RADIATED RF MEASUREMENT SETUP (30MHz~1GHz) RADIATED RF MEASUREMENT SETUP (Below 30MHz) POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP