2APUP-SC-CW-7GTScanstrut Waterproof Wireless Charger -Sub 3 Coil

Sub 3 Coil Electrical information & installation instructions. REV A For latest tech info visit: www.scanstrut.com Scanstrut Ltd 14 Dart Business Park, Clyst St. George, Exeter EX3 0QH SC-CW-1GT, SC-CW-2GT, SC-CW-7GT (ENG) READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT. (DE) LESEN SIE DIESE ANLEITUNG DURCH, BEVOR SIE MIT DER INSTALLATION BEGINNEN. (ES) LEA ESTAS INSTRUCCIONES ANTES DE INSTALAR EL PRODUCTO. (FR) VEUILLEZ PRENDRE CONNAISSANCE DE CES INSTRUCTIONS. (IT) AVANT DE PROCÉDER À L’INSTALLATION. (FIN) LUE NÄMÄ OHJEET ENNEN TUOTTEEN ASENTAMISTA. (SWE) LÄS DESSA INSTRUKTIONER INNAN PRODUKTEN INSTALLERAS. Part List Tools requiredOptional Drill Bits ø6mm (0.24") ø10mm (0.39") Jig SawFile LED indicator Instructions White LED Constant: ON Charge Red LED Constant: Standby (power ON) Red LED Flashing: Foreign object detection: metallic object placed on top that is not Qi compatible. OR Thermal cutout: The internal temperature is too high/ low. Wait for product to return to operating temperature. Router Calipers The product must be installed in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel/ vehicle and/or product failure. Scanstrut recommends installation is carried out by a qualified electrician. No liability is accepted for damage and/or injury caused by incorrect installation. The end-user is entirely responsible for conditions in which their device is used. See WARRANTY section for further details. WARNING: This product is to be connected to a 12V DC or 24V DC battery power source only. The power supply must be switched off before installation. An appropriate fuse or circuit breaker must be used between the battery / power source and this product. Check for correct polarity of all wiring before switching the power on. This product may contain high voltages. Do not tamper with the product. This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere e.g. engine room. Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects. Ensure any holes cut will not significantly weaken the structure of the mounting surface. If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged. CAUTION: The product is designed specifically for the charging of Qi compatible devices. The cable must be retained and not interfere with mechanical systems. This product contains no user serviceable components. Do NOT attempt to repair or alter the product in any way. This product will charge through non-metallic phone cases up to ~3mm thick. Phone cases may alter overall charge performance. When used in a very high/low ambient temperature/direct or prolonged sunlight the product may temporarily shut down, this is a safety feature of the electronics. The IP rating is only valid if correctly installed as per these instructions and on a perfectly flat, non-porous, smooth surface. The gasket ultimate bond strength will be achived after 72 hours at room temperature. When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly ventilated areas. EMC INSTALLATION GUIDELINES: Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations, to ensure that electromagnetic interference between equipment is minimised. Ensure the product is installed as directected in theses instructions. WIRING: When extending the cable from battery/ power source to the product, ensure there is consistently a minimum of 10V being provided to the product. A wire gauge of 18AWG (0.82mm2) is recommended for any length of cable extension. ENVIRONMENTAL PROTECTION: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. IMPORTANT: Scanstrut Ltd. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances. WARRANTY: A 5 year, non-transferable warranty covers this Scanstrut product only and not any devices that are positioned in it or on it. No warranty is given for users’ devices and users expose their devices to hazards, known or unknown, at their own risk. Waterproof Wireless Charger Technical IP Waterproof RatingIPX6 Front and back Input voltage10-30V DC (12/24V System) Input current max2A Output power max15W (12V 1.25A) Standby power max<1.2W Certification CE, UKCA, FCC, ROHS, C-Tick, UN ECE R10, PSE Certified Note: The electrical schematic is to illustrate how the product should be connected to a 12V DC or 24V DC battery/power supply. –Connect wires or connectors to 12/24V supply, ensuring a waterproof connection. –Fuse according to input voltage and current. –Check LED indicator for standby power. Min mounting material thickness 3mm (0.1") Min cavity space 54.5mm (2.15") FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installat…

Text truncated - open the document above for the full version.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Scanstrut Inc. FRN: 0033631300 Contact Name: Chris Beaudry Address: 7 Pequot Park Road Westbrook, CT, 06498 USA Telephone No: (860)308-14161 Email: [email protected] Applicant: Company name: Scanstrut Ltd. FRN: 0035671247 Product Description: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Grantee code: 2APUP FCC ID: 2APUP-SC-CW-7GT Contact Name: George W Bowles Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Telephone No: +44 (0) 1392 531280 Fax No: / Email: [email protected] [Scanstrut Ltd.] certifies that, as of the date of this filing of the application with the TCB, [Scanstrut Inc.] is our designated US agent for service of process for the above referenced FCC ID. [Scanstrut Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Scanstrut Inc.] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 07.09.2024 Applicant’s Name: George W Bowles US Agent’s Name: Chris Beaudry Title: Head of Design Title: VP, General Manager Signature Signature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Scanstrut Ltd. FRN: 0035671247 Grantee code: 2APUP FCC ID: 2APUP-SC-CW-7GT Contact Name: George W Bowles Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Telephone No: +44 (0) 1392 531280Fax No: / Email: [email protected] i. [Scanstrut Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Scanstrut Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. Scanstrut Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Date: 07.09.2024 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist Applicant’s Name: George W Bowles Title: Head of Design Signature

Scanstrut Ltd. Product Similarity Declaration Product name: Scanstrut Waterproof Wireless Charger-Sub 3 Coil Model name: SC-CW-7GT, SC-CW-1FT, SC-CW-2FT, SC-CW- 6FT, SC-CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC- CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW-10GT, SC-CW- 1FT-001, SC-CW-2FT-001, SC-CW-6FT-001, SC-CW-7FT-001, SC-CW-9FT-001, SC-CW-10FT-001, SC-CW-1GT-001, SC-CW- 2GT-001, SC-CW-6GT-001, SC-CW-7GT-001, SC-CW-9GT-001, SC-CW-10GT-001 FCC ID: 2APUP-SC-CW-7GT We (Scanstrut Ltd.) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), the only difference is the model name, plastic housing and packaging method. (Only the SC-CW-1GT and SC-CW-2GT plastic housing are different) Demonstrate the detail (descriptions and pictures) as to the difference list above. Scanstrut Ltd. SC-CW-7GT: SC-CW-1GT: Scanstrut Ltd. SC-CW-2GT: Signature: Name: George W Bowles Title: Head of Design Date: 07.09.2024

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Scanstrut Ltd. Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Product Name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Model Number: SC-CW-7GT, SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC- CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC-CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW-10GT, SC-CW-1FT-001, SC-CW-2FT-001, SC-CW-6FT- 001, SC-CW-7FT-001, SC-CW-9FT-001, SC-CW-10FT-001, SC-CW-1GT-001, SC-CW-2GT-001, SC-CW-6GT-001, SC-CW-7GT-001, SC-CW-9GT-001, SC- CW-10GT-001 FCC Identifier: 2APUP-SC-CW-7GT We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: George W Bowles Date: 7/16/2024 Title: Head of Design Signature of applicant:

C5266091_X10_Ed.1 1/1 Scanstrut Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/16/2024 Subject: Request for Confidentiality FCC ID: 2APUP-SC-CW-7GT To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: George W Bowles Date: 7/16/2024 Title: Head of Design

Page 1 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Photographs of the EUT (External Photos) Mode:SC-CW-7GT Page 2 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 3 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 4 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Mode:SC-CW-1GT Page 5 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 6 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 7 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Mode: SC-CW-2GT Page 8 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 9 of 9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected]

40mm +/- 10mm Label is sticked in the end of cable outer jacket, 40mm+/- 10mm distance。 FCC ID Label location

Page 1 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Photographs of the EUT (Internal Photos) Model:SC-CW-7GT Coil 3 Coil 2 Coil 1 Page 2 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 3 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Model:SC-CW-1GT Page 4 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Coil 1 Coil 2 Coil 3 Page 5 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 6 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Model:SC-CW-2GT Coil 1 Coil 2 Coil 3 Page 7 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Page 8 of 8 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected]

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Test Report Report No.: MTi240507001-05E2 Date of issue: 2024-06-27 Applicant: Scanstrut Ltd. Product name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Model(s): SC-CW-7GT, SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC-CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC-CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW-10GT, SC-CW-1FT-001, SC-CW-2FT-001, SC-CW-6FT-001, SC-CW-7FT-001, SC-CW-9FT-001, SC-CW-10FT-001, SC-CW-1GT-001, SC-CW-2GT-001, SC-CW-6GT-001, SC-CW-7GT-001, SC-CW-9GT-001, SC-CW-10GT-001 FCC ID: 2APUP-SC-CW-7GT Shenzhen Microtest Co., Ltd. http:// Web: www.mtitest.cn Page 2 of 15 Report No.: MTi240507001-05E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Instructions 1. This test report shall not be partially reproduced without the written consent of the laboratory. 2. The test results in this test report are only responsible for the samples submitted 3. This test report is invalid without the seal and signature of the laboratory. 4. This test report is invalid if transferred, altered, or tampered with in any form without authorization. 5. Any objection to this test report shall be submitted to the laboratory within 15 days from the date of receipt of the report. Page 3 of 15 Report No.: MTi240507001-05E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Contents 1 General Description .......................................................................................................................... 5 1.1 Description of the EUT ....................................................................................................................................... 5 1.2 Description of test modes ................................................................................................................................... 5 1.3 Description of support units ................................................................................................................................ 6 2 Measurement uncertainty ................................................................................................................. 6 3 Test facilities and accreditations ..................................................................................................... 7 3.1 Test laboratory .................................................................................................................................................... 7 4 List of test equipment ....................................................................................................................... 8 5 Test result........................................................................................................................................... 9 5.2 Test setup ......................................................................................................................................................... 10 5.3 Test Procedures ................................................................................................................................................ 10 5.4 Information of test equipment ........................................................................................................................... 11 5.5 Test results ....................................................................................................................................................... 12 Photographs of the Test Setup .............................................................................................................. 15 Photographs of the EUT ........................................................................................................................ 15 Page 4 of 15 Report No.: MTi240507001-05E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Test Result Certification Applicant: Scanstrut Ltd. Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Manufacturer: Scanstrut Ltd. Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Product description Product name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Trademark: SCANSTRUT Model name: SC-CW-7GT Series Model: SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC-CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC-CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW-10GT, SC-CW-1FT-001, SC-CW-2FT-001, SC-CW-6FT-001, SC-CW-7FT-001, SC-CW-9FT-001, SC-CW-10FT-001, SC-CW-1GT-001, SC-CW-2GT-001, SC-CW-6GT-001, SC-CW-7GT-001, SC-CW-9GT-001, SC-CW-10GT-001 Standards: FCC CFR 47 PART 1, § 1.1310 Test method: KDB 680106 D01 Wireless Power Transfer v04 Date of Test Date of test: 2024-05-24 to 2024-06-27 Test result: Pass Test Engineer : (Maleah Deng) Reviewed By : (David Lee) Approved By : (Leon Chen) Page 5 of 15 Report No.: MTi240507001-05E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] 1 General Description 1.1 Description of the EUT Product name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Model name: SC-CW-7GT Series Model: SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC-CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC-…

Text truncated - open the document above for the full version.

The test report is only used for customer scientific research, teaching, internal quality control and other purposes, and is for internal reference only. Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Test Report Report No.: MTi240507001-05E1 Date of issue: 2024-06-27 Applicant: Scanstrut Ltd. Product name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Model(s): SC-CW-7GT, SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC-CW-7FT, SC-CW-9FT, SC-CW-10FT, SC-CW-1GT, SC-CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW-10GT, SC-CW-1FT-001, SC-CW-2FT-001, SC-CW-6FT-001, SC-CW-7FT-001, SC-CW-9FT-001, SC-CW-10FT-001, SC-CW-1GT-001, SC-CW-2GT-001, SC-CW-6GT-001, SC-CW-7GT-001, SC-CW-9GT-001, SC-CW-10GT-001 FCC ID: 2APUP-SC-CW-7GT Shenzhen Microtest Co., Ltd. http://www.mtitest.cn Page 2 of 25 Report No.: MTi240507001-05E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Instructions 1. This test report shall not be partially reproduced without the written consent of the laboratory. 2. The test results in this test report are only responsible for the samples submitted 3. This test report is invalid without the seal and signature of the laboratory. 4. This test report is invalid if transferred, altered, or tampered with in any form without authorization. 5. Any objection to this test report shall be submitted to the laboratory within 15 days from the date of receipt of the report. Page 3 of 25 Report No.: MTi240507001-05E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Table of contents 1 General Description ........................................................................................................................... 5 1.1 Description of the EUT ............................................................................................................................... 5 1.2 Description of test modes .......................................................................................................................... 5 1.3 Environmental Conditions .......................................................................................................................... 6 1.4 Description of support units ....................................................................................................................... 6 1.5 Measurement uncertainty .......................................................................................................................... 6 2 Summary of Test Result .................................................................................................................... 7 3 Test Facilities and accreditations ..................................................................................................... 8 3.1 Test laboratory ........................................................................................................................................... 8 4 List of test equipment ........................................................................................................................ 9 5 Evaluation Results (Evaluation) ..................................................................................................... 10 5.1 Antenna requirement ............................................................................................................................... 10 6 Radio Spectrum Matter Test Results (RF) ..................................................................................... 11 6.1 20dB Occupied Bandwidth ...................................................................................................................... 11 6.2 Emissions in frequency bands (below 30MHz) ........................................................................................ 14 6.3 Emissions in frequency bands (30MHz - 1GHz) ...................................................................................... 17 Photographs of the test setup ............................................................................................................... 24 Photographs of the EUT ........................................................................................................................ 25 Page 4 of 25 Report No.: MTi240507001-05E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755) 88850135-1349 Fax: (86-755) 88850136 Web: http://www.mtitest.cn E-mail: [email protected] Test Result Certification Applicant: Scanstrut Ltd. Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Manufacturer: Scanstrut Ltd. Address: 14 Dart Business Park, Clyst St George, Exeter. EX3 0QH, UK Product description Product name: Scanstrut Waterproof Wireless Charger -Sub 3 Coil Trademark: SCANSTRUT Model name: SC-CW-7GT Series Model(s): SC-CW-1FT, SC-CW-2FT, SC-CW-6FT, SC-CW-7FT, SC-CW-9FT, SC- CW-10FT, SC-CW-1GT, SC-CW-2GT, SC-CW-6GT, SC-CW-9GT, SC-CW- 10GT, SC-CW-1FT-001, SC-CW-2FT-…

Text truncated - open the document above for the full version.