2AQL8-SMARTSYNCRXSmartSync Rx V2

ECO# 2388 REVISION# 000 ES 10-530 DATE 2/13/2026 SmartSync™ Wireless User Manual Non-Monitored Sensing Edge Transmitter, Non-Monitored Receiver, 3- Pushbutton Station, and Remote 2 Table of Contents Section 1 – Safety Check List 3 Section 2 – Introduction 5 Section 3 – Wiring & Installation 7 Section 4 – Setup & Operation 11 Section 5 – Troubleshooting 20 3 Section 1 – Safety Check List Rolling doors are large, movable objects. They move with the help of electric motors or manual operators (chain, crank, push up, etc.), and most have springs under high tension. These items and their components can cause injury. In order to avoid injury to yourself and others, please follow the instructions in this manual. INSTALLATION, REPAIR, AND MAINTENANCE OF THIS PRODUCT REQUIRES SUBSTANTIAL KNOWLEDGE AND EXPERIENCE WITH THE INSTALLATION, REPAIR, AND MAINTENANCE OF ROLLING DOORS, THEIR PARTS AND SYSTEMS, AND THE RISKS ASSOCIATED WITH THEM. THIS PRODUCT SHOULD BE INSTALLED, REPAIRED, AND MAINTAINED ONLY BY A PROFESIONAL TRAINED IN ROLLING DOOR INSTALLATION, REPAIR, AND MAINTENANCE (“PROFESSIONAL INSTALLER(S)”). HAVING SOMEBODY ELSE INSTALL, REPAIR, OR MAINTAIN THIS PRODUCT PUTS THEM AND THOSE AROUND THE DOOR IN DANGER OF SERIOUS INJURY OR DEATH. IF ANY PART OF THIS MANUAL IS UNCLEAR (INCLUDING THIS WARNING) OR IF ADDITIONAL INFORMATION IS NEEDED, THE INDIVIDUAL INSTALLING, REPAIRING, OR MAINTAINING THE PRODUCT MUST CONTACT CORNELLCOOKSON’S TECHNICAL SUPPORT DEPARTMENT.  Review the potential hazards and preventative measures listed below: Potential Hazard Preventative Measure Pinned or crushed by closing door. • Keep yourself and others clear of opening while door is in motion. • Do not allow children to play near or operate door. • Do not operate if door becomes jammed, broken or does not operate smoothly. Immediately stop use and contact a Professional Installer for repair. Struck by adjusting wheel bar while applying spring turns. • Be sure bar is adequate in strength and long enough to allow installer to apply the necessary torque. (Refer to “Applying Spring Turns” section for bar size recommendations.) • Make sure bar is fully seated into the adjusting wheel slot before applying pressure. • Use two bars while applying turns to the adjusting wheel. • Follow the steps under “Curtain Installation” closely. Electrical shock. • Make sure electrical operator is properly grounded. • Turn off source power completely prior to servicing the motor. • Make sure wires are clear of any moving or potentially moving parts. • Avoid pinching wires when installing the motor cover. Pinched by moving components. • Make sure the motor is turned off and unplugged before working with moving parts such as roller chain and sprockets, drop-out mechanisms, adjusting wheels, etc. • Locate all possible pinch points of the unit (such as the drive chain, coil area, bottom bar, etc.). The door should be disconnected from power and/or locked down if someone is working on or near these areas. Table 2.1 - Potential hazards and Preventative Measures  Check the following during installation and before leaving the job site:  If the unit has tension springs, be sure the proper amount of tension is applied to the torsion springs in order to properly counterbalance the weight of the curtain.  Securely fasten the tension adjusting wheel in place with the appropriate hardware provided as shown in the “Curtain Installation” section of these instructions. 4  Check that the keys and/or cotter pins have been set in place and fit properly at all sprockets or gears.  Check that the setscrews in each sprocket or gear (one over the key and one offset from the key) have been tightened properly.  Check all fasteners holding the unit to the building structures to ensure the correct type have been installed and have the correct torque/tightness.  Instruct owner or their representative in the proper method of operating and maintaining the door, review all warnings on the door and in this manual, and leave a copy of this manual. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) This device may not cause harmful interference, and (2 ) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body . (SmartSync Rx V2, SmartSync Lv, SmartSync 3pbs) FCC Statement 5 Section 2 – Introduction The SmartSync Wireless Non-Monitored Receiver is an essential device for the SmartSync Wireless Device offering. All the devices within the SmartSync Wireless offering require a SmartSync Wireless Receiver for operation. Furthermore, all devices must go through a pairing process with the Wireless Receiver at install. This Wireless Receiver is powered and wired through/to the operator controller of the door. It is intended to be mounted in close proximity to the controller. The SmartSync Wireless Non- Monitored Receiver is intended for use with the SmartSync Wireless Non-Monitored Sensing Edge Transmitter, the SmartSync Wireless Remote, and the SmartSync Wireless 3-Pushbutton Station. Note: The SmartSync Wireless Non-Monitored Receiver ( Model No: 202981) is limited to applications where a connected sensing edge will not fulfill a primary entrapment requirement as part of UL 325. If used in a UL 325 certified operator application, the Non-Monitored Receiver and its corresponding Non- Monitored Sensing Edge Transmitter can only be used as a secondary/ancillary entrapment device. For UL 325 primary entrapment applications, the Model No: 201430 Wireless Receiver and its compatible devices …

Text truncated - open the document above for the full version.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name CornellCookson LLC Address 24 Elmwood Avenue, Mountain Top, PA, 18707, United States FRN 0027695386 Grantee Code 2AQL8 FCC ID: 2AQL8-SMARTSYNCRX Authorized Contact Name Xin Cui Contact Phone +1-602-272-4244 1164 Contact Email [email protected] I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1)labeling the equipment with the exact FCC ID as specified in this application, (2)compliance statement labeling pursuant to the applicable rules, (3)compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1)the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc. terms and conditions as specified in the TCB Application Form 731 (QSF27-14-01). Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List Applicant Signature: Date: 2026-08-17 Print Name: Xin Cui Title: Manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.4 April 25, 2025Page 1 of 1 Original Issue: Jan. 4, 2021

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States FCC COVERED LIST DECLARATION LETTER Applicant Legal Business NameCornellCookson LLC Address24 Elmwood Avenue, Mountain Top, PA, 18707, United States FRN0027695386 Grantee Code2AQL8FCC ID:2AQL8-SMARTSYNCRX Authorized Contact NameXin Cui Contact Phone+1-602-272-4244 1164Contact [email protected] CornellCookson LLC (“the applicant”) certifies: -the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. -as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. -the software to be loaded prior to marketing of the equipment identified above is not “covered” software manufactured by any entity including predecessors, successors, parents, subsidiaries, affiliates or any entity which has rebranded or relabeled the software produced by the entity(ies) identified on the “Covered List”. -the device is not capable of storing or running software listed on the covered list and therefore is inherently compliant. Link to the Covered List: Covered List Applicant Signature:Date: 2026-08-17 Print Name:Xin Cui Title:Manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Page 1 of 1 Revision 1.0

UNITED STATES DESIGNATED AGENT LETTER Date: 2026-08-17 TO:Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 ApplicantU.S. designated agent Company Name:CornellCookson LLCCompany Name:CornellCookson LLC FRN:0027695386FRN:0027695386 Grantee Code:2AQL8 Contact Name:Xin CuiContact NameXin Cui Address:24 Elmwood AvenueAddress:24 Elmwood Avenue City/Province/Zip:Mountain Top, Pennsylvania, United States, 18707 City/Province/Zip:Mountain Top, Pennsylvania, United States, 18707 Telephone:+1-602-272-4244 1164Telephone:+1-602-272-4244 1164 Fax:/Fax:/ Email:[email protected]:[email protected] Applicable Equipment: FCC ID: <2AQL8-SMARTSYNCRX > ATTN: Director of Certification: We, < CornellCookson LLC > and < CornellCookson LLC > understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < CornellCookson LLC > and < CornellCookson LLC > acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. ApplicantU.S. designated agent Name (Printed): Xin CuiName (Printed): Xin Cui Title: ManagerTitle: Manager Signature:Signature:

< CornellCookson LLC > Date: 2026-08-04 TO:Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AQL8-SMARTSYNCRX To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with CornellCookson LLC This authorization is valid until further written notice from the applicant. Name (Printed): Xin Cui Title: Manager Signature: On behalf of Company: CornellCookson LLC Telephone: +1-602-272-4244 1164

CornellCookson LLC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From:CornellCookson LLC 24 Elmwood Avenue, Mountain Top, PA, 18707 , United States Regarding: Confidentiality Request regarding application for FCC ID: 2AQL8-SMARTSYNCRX LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code): Xin Cui Company Name: CornellCookson LLC

Compliance Certification Services (Kunshan) Inc. Page: 1 of 4 External Photos for KSCR2510002262AT Test Model No.: 202981 Compliance Certification Services (Kunshan) Inc. Page: 2 of 4 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Page: 4 of 4

Label location

Compliance Certification Services (Kunshan) Inc. Page: 1 of 6 Internal Photos for KSCR2510002262AT Test Model No.: 202981 Compliance Certification Services (Kunshan) Inc. Page: 2 of 6 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 6 Compliance Certification Services (Kunshan) Inc. Page: 4 of 6 Compliance Certification Services (Kunshan) Inc. Page: 5 of 6 Compliance Certification Services (Kunshan) Inc. Page: 6 of 6

Report No.: KSCR251000226202 Page: 1 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 1 Cover Page RF Exposure Evaluation Report Application No.: KSCR2510002262AT FCC ID: 2AQL8-SMARTSYNCRX Applicant: CornellCookson LLC Address of Applicant: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Manufacturer: CornellCookson LLC Address of Manufacturer: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Factory: CornellCookson LLC Address of Factory: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Equipment Under Test (EUT): EUT Name: SmartSync Rx V2 Model No.: 202981 Trade Mark: SMARTSYNC Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2025-10-15 Date of Test: 2025-10-29 to 2025-11-04 Date of Issue: 2025-11-20 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: KSCR251000226202 Page: 2 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 Revision Record Version Description Date Remark 00 Original 2025-11-20 / Authorized for issue by: Tested By Eric Liu /Project Engineer Approved By Terry Hou /Reviewer Report No.: KSCR251000226202 Page: 3 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 2 Contents Page 1 Cover Page ........................................................................................................................................ 1 2 Contents ............................................................................................................................................ 3 3 General Information .......................................................................................................................... 4 3.1 General Description of E.U.T. .................................................................................................... 4 3.2 Technical Specifications ............................................................................................................. 4 3.3 Separation Distance ................................................................................................................... 4 3.4 Test Location .............................................................................................................................. 5 3.5 Test Facility ................................................................................................................................ 5 4 RF Exposure Test Exemptions ........................................................................................................ 6 4.1 FCC RF Exposure Test Exemptions for single RF sources ....................................................... 6 4.2 RF Exposure Test Exemptions for Simultaneous Transmission ................................................ 8 5 Measurement and Calculation ....................................................................................................... 10 5.1 Maximum transmit power ......................................................................................................... 10 5.2 RF Exposure Calculation ......................................................................................................... 11 Report No.: KSCR251000226202 Page: 4 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 3 General Information 3.1 General Description of E.U.T. Power supply: DC 24V 3.2 Technical Specifications Zigbee Operation Frequency: 2405MHz to 2480MHz Modulation Type: O-QPSK Number of Channels: 16 Channel Spacing: 5MHz Antenna Type: PCB Antenna Antenna Gain: 3dBi (Provided by the manufacturer) 3.3 Separation Distance Separation distance between the antenna to person (R): ＞20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. R has been stated in user manual. Report No.: KSCR251000226202 Page: 5 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 3.4 Test Location All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China. Tel: +86 512 5735 5888 Fax: +86 512 5737 0818 No tests were sub-contracted. Note: 1.SGS is not responsible for wrong test results due to incorrect information (e.g. max. clock frequency, highest internal frequency, antenna gain, cable loss, etc ) is provided by the applicant. (if applicable). 2.SGS is not responsible for the authenticity, integrity and the validity of the conclusion based on results of the data provided by applicant. (if applicable). 3. Sample source: sent by customer. 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA Compliance Certification Services (Kunshan) Inc. is accredited by the American Association for Laboratory Accreditation (A2LA). Certificate No. 2541.01. • FCC Compliance Certification Services (Kunshan) Inc. has been recognized as an accredited testing laboratory. Designation Number: CN1172. • ISED Compliance Certification Services (Kunshan) Inc. has been recognized by Innovation, Science and Economic Development Canada (ISED) as an accredited testing laboratory. Company Number: 2324E • VCCI The 3m and 10m Semi-anechoic chamber and Shielded Room of Compliance Certification Services (Kunshan) Inc. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-20134, R-11600, C-11707, T-11499, G-10216 respectively. Report No.: KSCR251000226202 Page: 6 of 11 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 4 RF Exposure Test Exemptions Test exemptions apply for devices used in general population/uncontrolled exposure environments, according to the SAR-based, or MPE-based exemption thresholds. 4.1 FCC RF Exposure Test Exemptions for single RF sources 4.1.1 Blanket 1 mW Blanket Exemption The 1 mW Blanket …

Text truncated - open the document above for the full version.

承认书项目表 内容 页数页码 NO. （Number（Page （ Contents ） ofPage ） Code ） 1 承认书封面（ SpecCover ） 11 2 承认书项目表（ SpecItem ） 12 3 工程成品图（ Drawing ） 13 4 电性测试报告（ TestReports ） 14 5 S 参数测试（ SParameter ） 15 6 增益测试（ GainTest ） 16 7 8 9 10--- 11--- 12--- 东莞市脉讯电子有限公司Tel:0769-33691210Fax:0769-82381572 Zn 电性测试报告 Test Reports 3 dBi , PCB Antenna <= 2.0 Sample Photo A. Electrical Characteristics Frequency 2400 ~ 2500 MHz S.W.R. Antenna Gain Polarization Linear Impedance 50 Ohm B. Material & Mechanical Characteristics Material of Radiator Cu Material of Plastic Body: TPE Hinge: PA+ABS Holder: PA+ABS Cable Type RG-178 Connector Type SMA Male Reverse Connector Pull Test >= 3 Kg Connector Torque Test 200~600g.cm C. Environmental Operation Temperature - 40 °C ~ + 65 °C Storage Temperature - 40 °C ~ + 80 °C 东莞市脉讯电子有限公司Tel:0769-33691210Fax:0769-82381572 S 参数测试 SParameterTest AgilentE5071C 东莞市脉讯电子有限公司Tel:0769-33691210Fax:0769-82381572 增益测试 GainTest Antenna Radiation Pattern VS Gain 东莞市脉讯电子有限公司Tel:0769-33691210Fax:0769-82381572 Contact Information: Dongguan Maixun Electronics Co., Ltd. Room 405, 4th Floor, No.6 Qilin East Road, Daning Community, Humen Town, Dongguan City, Guangdong Province, P.R.China

Report No.: KSCR251000226201 Page: 1 of 55 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 TEST REPORT Application No.: KSCR2510002262AT FCC ID: 2AQL8-SMARTSYNCRX Applicant: CornellCookson LLC Address of Applicant: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Manufacturer: CornellCookson LLC Address of Manufacturer: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Factory: CornellCookson LLC Address of Factory: 24 Elmwood Avenue, Mountain Top, PA, 18707, United States Equipment Under Test (EUT): EUT Name: SmartSync Rx V2 Model No.: 202981 Trade Mark: SMARTSYNC Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2025-10-15 Date of Test: 2025-10-29 to 2025-11-04 Date of Issue: 2025-11-20 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: KSCR251000226201 Page: 2 of 55 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 Revision Record Version Description Date Remark 00 Original 2025-11-20 / Authorized for issue by: Tested By Eric_Liu/Project Engineer Approved By Terry Hou /Reviewer Report No.: KSCR251000226201 Page: 3 of 55 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10- 2020+Cor 1-2023 Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10- 2020+Cor 1-2023 Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10- 2020+Cor 1-2023 Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Conducted Peak Output Power ANSI C63.10- 2020+Cor 1-2023 Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10- 2020+Cor 1-2023 Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10- 2020+Cor 1-2023 Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10- 2020+Cor 1-2023 Section 6.10.4 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10- 2020+Cor 1-2023 Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Report No.: KSCR251000226201 Page: 4 of 55 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 Test Summary ......................................................................................................................................... 3 3 Contents ................................................................................................................................................... 4 4 General Information ................................................................................................................................ 5 4.1 Details of E.U.T. ............................................................................................................................... 5 4.2 Power level setting using in test ....................................................................................................... 5 4.3 Description of Support Units ............................................................................................................ 5 4.4 Measurement Uncertainty ................................................................................................................ 6 4.5 Test Location .................................................................................................................................... 7 4.6 Test Facility ...................................................................................................................................... 7 4.7 Deviation from Standards ................................................................................................................. 7 4.8 Abnormalities from Standard Conditions .......................................................................................... 7 5 Equipment List ........................................................................................................................................ 8 6 Radio Spectrum Technical Requirement .............................................................................................. 9 6.1 Antenna Requirement ...................................................................................................................... 9 7 Radio Spectrum Matter Test Results .................................................................................................. 10 7.1 Radiated Emissions which fall in the restricted bands ................................................................... 10 7.2 Radiated Spurious Emissions Below 1GHz ................................................................................... 18 7.3 Radiated Spurious Emissions Above 1GHz ................................................................................... 22 7.4 Conducted Peak Output Power ...................................................................................................... 30 7.5 Minimum 6dB Bandwidth................................................................................................................ 31 7.6 Power Spectrum Density ................................................................................................................ 32 7.7 Conducted Band Edges Measurement .......................................................................................... 33 7.8 Conducted Spurious Emissions ..................................................................................................... 34 8 Test Setup Photo .........................…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 3 Appendix Photographs of Test Setup for KSCR2510002262AT Test Model No.: 202981 Compliance Certification Services (Kunshan) Inc. Page: 2 of 3 Test Setup Photo RF Conducted setup Radiated Spurious Emissions Below 1GHz Compliance Certification Services (Kunshan) Inc. Page: 3 of 3 Radiated Spurious Emissions Above 1GHz