2AQQU-01LC100S0LC100-Receiver

Lok-Antenne 410 – 430 / 450 – 470 MHz K 70 21 21, 725 892 •2 dB-Breitband-Antenne in Fiberglas-Schutzhaube. Typ Nr.K 70 21 21725 892 EingangN-Buchse Frequenzbereich450 – 470 MHz410 – 430 MHz VSWR< 1,5 Gewinn2 dB (bezogen auf den λ / 4 -Strahler) Impedanz50 Ohm PolarisationVertikal Max. Belastung640 Watt (bei 50° C Umgebungstemperatur) Gewicht0,8 kg Verpackungsmaße415 x 151 x 90 mm Material:Strahler und Flansch: Aluminium. Schutzhaube: Fiberglas, Farbe: Hellgrau. Alle Schrauben und Muttern: Rostfreier Stahl. Befestigung:Auf einer leitenden Fläche mit einer Mindest- größe von 50 x 50 cm mit 4 Stehbolzen M10. Erdung und Die von der Deutschen Bahn AG geprüfte Hochspannungsschutz:Antenne ist blitzgeschützt und gesichert bei Berührung mit Hochspannungsleitungen, da alle Metallteile an Masse liegen. Montageflansch: Montagebohrung für den Anschlußstecker: Ø 33 (max. Ø 35) mm. Hinweis:Montagefläche lackfrei halten für Massekontakt! KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . Postfach 10 04 44 . D-83004 Rosenheim . Deutschland . Telefon (0 80 31) 18 40 . Fax (0 80 31) 18 49 91 Train Antenna 410 – 430 / 450 – 470 MHz K 70 21 21, 725 892 Material:Radiator and Flange: Aluminum. Radome: Fiberglass, colour: Light grey. All screws and nuts: Stainless steel. Mounting:On a conductive surface with a minimum size of 50 x 50 cm by means of existing M10 studs. Grounding and highThis antenna approved by the “Deutsche Bahn voltage protection:AG” is D.C. grounded to protect against lightning and high tension lines. Mounting flange: Mounting hole for the connector: 33 (max. 35) mm diameter. Note:Keep mounting surface clear of paint for electrical contact. Type No.K 70 21 21725 892 InputN-female Frequency range450 – 470 MHz410 – 430 MHz VSWR< 1.5 Gain2 dB (ref. to the quarter-wave antenna) Impedance50 Ohm PolarizationVertical Max. power640 Watt (at 50° C ambient temperature) Weight0.8 kg Packing size415 x 151 x 90 mm •2 dB gain broadband antenna in fiberglas radome. KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone (++49) 8031 / 184-0 . Fax (++49) 8031 / 184-991

Fahrzeug-Antenne 410 – 470 MHz K 70 20 21 •Besonders kurze Breitband-Antenne in Fiberglas- Schutzhaube. Typ Nr.K 70 20 21 EingangN-Buchse Frequenzbereich410 – 470 MHz VSWR< 1,5 Gewinn0 dB (bezogen auf den λ / 4 -Strahler) Impedanz50 Ohm PolarisationVertikal Max. Belastung170 Watt (bei 50° C Umgebungstemperatur) Gewicht0,5 kg Verpackungsmaße210 x 151 x 87 mm Höhe142 mm Material:Strahler und Flansch: Aluminium. Schutzhaube: Fiberglas, Farbe: Hellgrau. Alle Schrauben und Muttern: Rostfreier Stahl. Befestigung:Auf einer leitenden Fläche mit einer Mindest- größe von 50 x 50 cm mit 4 Stehbolzen M10. Erdung und Die von der Deutschen Bahn AG geprüfte Hochspannungsschutz:Antenne ist blitzgeschützt und gesichert bei Berührung mit Hochspannungsleitungen, da alle Metallteile an Masse liegen. Montageflansch: Montagebohrung für den Anschlußstecker: Ø 33 (max. Ø 35) mm. Hinweis:Montagefläche lackfrei halten für Massekontakt! 142 mm 936.005/b Änderungen vorbehalten. KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . Postfach 10 04 44 . D-83004 Rosenheim . Deutschland . Telefon (0 80 31) 18 40 . Fax (0 80 31) 18 49 91 •Low profile broadband antenna in fiberglass radome. Train Antenna 410 – 470 MHz K 70 20 21 Material:Radiator and Flange: Aluminum. Radome: Fiberglass, colour: Light grey. All screws and nuts: Stainless steel. Mounting:On a conductive surface with a minimum size of 50 x 50 cm by means of existing M10 studs. Grounding and highThis antenna approved by the “Deutsche Bahn voltage protection:AG” is D.C. grounded to protect against lightning and high tension lines. Mounting flange: Mounting hole for the connector: 33 (max. 35) mm diameter. Note:Keep mounting surface clear of paint for electrical contact. Type No.K 70 20 21 InputN-female Frequency range410 – 470 MHz VSWR< 1.5 Gain0 dB (ref. to the quarter-wave antenna) Impedance50 Ohm PolarizationVertical Max. power170 Watt (at 50° C ambient temperature) Weight0.5 kg Packing size210 x 151 x 87 mm Height142 mm 936.005/b Subject to alteration. 142 mm KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone (++49) 8031 / 184-0 . Fax (++49) 8031 / 184-991

LocControl100 Page 1 of 28 General operating instructions 10.0296.6600.01 Version N LocControl100 General operating instructions (customer-specific aspects are described in a separate document) Document no. 10.0296.6600.02 Version N Author: Gerhard Jordi The contents of this manual are the intellectual property of Schweizer Electronic AG. No user rights to patents or other property rights are granted to third parties through its acquisition. All rights remain with Schweizer Electronic. Except with our express permission, this manual may not be copied or duplicated, either completely or partially, and it may not be communicated or made accessible to third parties. LocControl100 Page 2 of 28 General operating instructions 10.0296.6600.01 Version N Contents 0 DOCUMENT INFORMATION .................................................................................................................. 4 0.1 DOCUMENT OBJECTIVE ................................................................................................................................ 4 0.2 VERSION CONTROL ..................................................................................................................................... 4 1 INTRODUCTION ...................................................................................................................................... 5 1.1 GENERAL REMARKS .................................................................................................................................... 5 1.2 ISED RSP-100 NOTICE: ............................................................................................................................ 6 2 PICTOGRAMS ......................................................................................................................................... 7 3 LOCCONTROL100 COMMISSIONING AND MAINTENANCE CONCEPT ............................................ 8 3.1 INTRODUCTION ........................................................................................................................................... 8 3.2 COMMISSIONING ENGINEERS’ ACTIVITIES: ..................................................................................................... 8 3.3 MAINTENANCE ENGINEERS’ ACTIVITIES: ........................................................................................................ 8 3.4 OPERATOR ................................................................................................................................................. 8 3.5 MANUFACTURERS ....................................................................................................................................... 8 3.6 PERSONNEL COMPETENCE .......................................................................................................................... 8 3.7 QUALIFICATION OVERVIEW........................................................................................................................... 9 3.8 THE SERVICE ORGANIZATION ....................................................................................................................... 9 4 DEVICE DESCRIPTION ........................................................................................................................ 10 4.1 OPERATING PRINCIPLE .............................................................................................................................. 10 4.2 TRANSMITTER ........................................................................................................................................... 10 4.3 RECEIVER ................................................................................................................................................ 10 4.4 RECEIVER  → TECHNICAL UNIT INTERFACE .............................................................................................. 10 5 SYSTEM SECURITY.............................................................................................................................. 11 5.1 ADDRESSING ............................................................................................................................................ 11 5.2 TRANSMISSION SECURITY ON THE RADIO CHANNEL ..................................................................................... 13 6 STANDARDS, GUIDELINES AND COMPANY-INTERNAL REGULATIONS ...................................... 13 6.1 STANDARDS, GUIDELINES AND COMPANY-INTERNAL REGULATION HIERARCHY ............................................... 13 6.2 OBSERVED STANDARDS ............................................................................................................................ 13 6.3 RADIO MODULE „MSY“ NOTIFICATIONS ....................................................................................................... 14 6.4 LOCCONTROL100 RS NOTIFICATIONS ........................................................................................................ 14 7 INTENDED USE OF THE RADIO REMOTE CONTROL ...................................................................... 14 8 SAFETY INFORMATION ....................................................................................................................... 15 8.1 GENERAL SAFETY INFORMATION ................................................................................................................ 15 8.2 GENERAL OPERATING SAFETY GUIDELINES ................................................................................................. 15 8.3 SAFETY INFORMATION FOR OPERATION ...................................................................................................... 16 8.4 COMPORTMENT IN EMERGENCY SITUATIONS ............................................................................................... 16 9 COMPORTMENT IN CASE OF THUNDERSTORMS ........................................................................... 16 10 TRANSMITTER ...............................…

Text truncated - open the document above for the full version.

Schweizer Electronic AG Industriestrasse 3 CH-6260 Reiden Phone +41 (0)62 / 749 07 07 Fax +41 (0)62 / 749 07 00 e-mail [email protected] SCHWEIZER ELECTRONIC The content of this report is the intellectual property of Schweizer Electronic AG. Third parties do not obtain right of use of patents or any other intellecutal property rights by purchasing this report. All rights remain with Schweizer Electronic AG. This report may not be copied or reproduced, in whole or in part, nor shared with or made available to third parties. Date: 25. Juli 2020 1 / 19 LocControl100 RS Instructions for Installing LocControl100 on the vehicle Document No. 10.0296.6021.01 Version I Authors: Gerhard Jordi / Robert Büchi SCHWEIZER ELECTRONIC Page 2 of 19 Table of contents 1 DOCUMENT NOTES ............................................................................................................................... 3 1.1 PURPOSE OF THIS DOCUMENT ..................................................................................................................... 3 1.2 VERSION CONTROL ..................................................................................................................................... 3 1.3 RELATED DOCUMENT .................................................................................................................................. 3 2 INTRODUCTION ...................................................................................................................................... 4 3 PICTOGRAM ............................................................................................................................................ 4 4 USING SCHWEIZER ELECTRONIC MATERIALS ................................................................................. 4 5 OPENING LOCCONTROL100 RS TRANSMITTER AND RECEIVER ................................................... 5 6 CONNECTING AND INSTALLING THE 19“ RACK MODEL RECEIVER .............................................. 6 6.1 MECHANICAL INSTALLATION ......................................................................................................................... 6 6.2 ELECTRICAL CONNECTION ........................................................................................................................... 6 7 INSTALLING COMPACT MODEL RECEIVER ....................................................................................... 7 7.1 MECHANICAL INSTALLATION ......................................................................................................................... 7 7.2 INSTALLATION POSITION FOR COMPACT RECEIVER MODEL ............................................................................. 7 7.3 ELECTRICAL CONNECTION ........................................................................................................................... 7 8 INSTALLING RECEIVER MODEL WITH IP65 HOUSING ...................................................................... 8 8.1 MECHANICAL INSTALLATION ......................................................................................................................... 8 8.2 REQUIRED INSTALLATION MATERIAL ............................................................................................................. 8 8.3 ELECTRICAL CONNECTION ........................................................................................................................... 8 9 EARTHING OF THE RECEIVER ............................................................................................................. 9 9.1 EARTHING OF RECEIVER MODELS 19“ RACK/RELAY AND 19“ RACK/CANOPEN ............................................... 9 9.2 EARTHING OF THE COMPACT MODEL RECEIVER ............................................................................................ 9 9.3 EARTHING OF IP65 MODEL RECEIVER .......................................................................................................... 9 10 WIRING THE RECEVIER WITH SUPPLY CABLE AND SIGNAL CABLE .......................................... 10 10.1 USING SHIELDED SIGNAL CABLE ............................................................................................................. 10 10.2 19“ RACK MODEL RECEIVER WITH RELAY INTERFACE .............................................................................. 10 10.3 19“ RACK MODEL RECEIVER WITH CANOPEN INTERFACE ........................................................................ 10 10.4 COMPACT MODEL RECEIVER WITH CANOPEN INTERFACE ....................................................................... 11 10.5 RECEIVER WITH IP65 HOUSING ............................................................................................................. 11 11 VEHICLE ANTENNAS ........................................................................................................................... 12 11.1 AVAILABLE VEHICLE ANTENNAS .............................................................................................................. 12 11.2 MOUNTING THE ANTENNA ...................................................................................................................... 12 11.2.1 Metallic surface ........................................................................................................................... 12 11.2.2 Non-metallic surfaces ................................................................................................................. 12 11.2.3 Earthing the vehicle antenna ...................................................................................................... 12 11.2.4 Sealing the vehicle antenna ........................................................................................................ 13 11.2.5 Painting the vehicle antenna ....................................................................................................... 13 11.2.6 Aligning the antenna ...............................…

Text truncated - open the document above for the full version.

23.09.2019 TIMCO Engineering Inc. 849 NW State Road, 45, Newberry, FL-32669 Dear Sir or Madam, We, Schweizer Electronic AG, hereby authorize H.B. Compliance Solutions, Mr. Hoosamuddin, to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 23 rd of September 2020. Sincerely, Company Officer: Thomas Koch Email: [email protected]

23.09.2019 TIMCO Engineering 849 NW State Road 45, Newberry, FL-32669, Confidentiality Request FCC ID: 2AQQU-01LC100S0 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, Schweizer Electronic AG hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation Tune-Up Procedure Schweizer Electronic AG also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of 180 days: Internal Photos User Manual Test Set-up Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name: Thomas Koch Title: Product Manager

External Photos - Stationary Part

Picture or art work of the label with FCC ID for RX

Label location LC100-Receiver

Radio Module HAP1361 TOP HAP1361 BOTTOM HAP1398 TOP HAP1398 BOTTOM HAP1339 TOP HAP1339 BOTTOM Internal wiring

Certificates and reports shall not be reproduced except in full, without the written permission of H.B Compliance Solutions, LLC. Maximum Permissible Exposure Statement For the Schweizer Electronic AG LocControl 100 (Receiver) November 14, 2019 Prepared for: Schweizer Electronic AG Industriestrasse 3, CH-6260 Reiden, Switzerland Prepared By: H.B. Compliance Solutions 5005 S. Ash Avenue, Suite # A-10 Tempe, Arizona 85282 Reviewed By: Hoosamuddin Bandukwala Cert # ATL-0062-E HBCS MPE Report # EMC_17050_1 Rev1 Page 2 of 2 Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S = PG/4πR² Where, S = power density (mW/cm2) P = output power at the antenna terminal (mW) G = gain of transmit antenna (numeric) R = distance from transmitting antenna (cm) Maximum peak output power at antenna input terminal = 27.4 (dBm) Maximum peak output power at antenna input terminal = 550 (mW) Antenna gain (typical) = 6 (dBi) Maximum antenna gain = 3.98 (numeric) Prediction distance = 31 (cm) Prediction frequency = 450 (MHz) MPE limit for uncontrolled exposure at prediction frequency = 0.30 (mW/cm^2) Power density at prediction frequency = 0.181269 (mW/cm^2) To solve for the minimum mounting distance required; R = √ (PG/4πS) R = √ (550 x 3.98 / 4π x 0.181269) = 31 cm (Based on continuous transmission) HBCS MPE Report # EMC_17050_1 Rev1 Page 3 of 2 Maximum peak output power at antenna input terminal = 27.4 (dBm) Maximum peak output power at antenna input terminal = 550.0 (mW) Antenna gain (typical) = 2 (dBi) Maximum antenna gain = 1.58 (numeric) Prediction distance = 20 (cm) Prediction frequency = 450 (MHz) MPE limit for uncontrolled exposure at prediction frequency = 0.30 (mW/cm^2) Power density at prediction frequency = 0.17288 (mW/cm^2) To solve for the minimum mounting distance required; R = √ (PG/4πS) R = √ (550 x 1.58 / 4π x 0.17288) = 20 cm (Based on continuous transmission) END OF TEST REPORT

Certificates and reports shall not be reproduced except in full, without the written permission of H.B Compliance Solutions, LLC. Intentional Radiator Test Report For the Schweizer Electronic AG LC100-Receiver Tested under The FCC Rules contained in Title 47 of the CFR, Part 90 for Private Land Mobile Radio Services November 14, 2019 Prepared for: Schweizer Electronic AG Industriestrasse 3, CH-6260 Reiden, Switzerland Prepared By: H.B. Compliance Solutions 5005 S. Ash Avenue, Suite A-10 Tempe, Arizona 85282 Reviewed By: Hoosamuddin Bandukwala Cert # ATL-0062-E Engineering Statement: The measurements shown in this report were made in accordance with the procedure indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurement made, the equipment tested is capable of operation in accordance with the requirements of Part 90 of the FCC Rules under normal use and maintenance. All results contained herein relate only to the sample tested. HBCS Report # EMC_17050_1 Rev1 Page 2 of 35 Report Status Sheet Revision # Report Date Reason for Revision Ø November 14, 2019 Initial Issue 1 June 22, 2020 TCB Comments HBCS Report # EMC_17050_1 Rev1 Page 3 of 35 Table of Contents EXECUTIVE SUMMARY ............................................................................................ 4 1. Testing Summary ........................................................................................ 4 EQUIPMENT CONFIGURATION ................................................................................ 5 1. Overview .................................................................................................... 5 2. Test Facility ................................................................................................. 6 3. Description of Test Sample ......................................................................... 7 4. Equipment Configuration ........................................................................... 7 5. Support Equipment .................................................................................... 7 6. Ports and Cabling Information .................................................................... 7 7. Method of Monitoring EUT Operation ........................................................ 7 8. Mode of Operation ..................................................................................... 8 9. Modifications ............................................................................................. 8 10. Disposition of EUT ...................................................................................... 8 Criteria for Intentional Radiators ............................................................................ 9 1. RF Power Output ........................................................................................ 9 2. Modulation Characteristics ....................................................................... 12 3. Occupied Bandwidth (Emission Mask) ...................................................... 14 4. Spurious Emissions at Antenna Terminals ................................................ 17 5. Radiated Spurious Emissions .................................................................... 24 6. Frequency Stability vs Temperature ......................................................... 27 7. Frequency Stability vs Voltage .................................................................. 29 8. Transient Frequency Behavior .................................................................. 31 9. Necessary Bandwidth ............................................................................... 33 10. Test Equipment ........................................................................................ 34 11. Measurement Uncertainty ....................................................................... 35 HBCS Report # EMC_17050_1 Rev1 Page 4 of 35 EXECUTIVE SUMMARY 1. Testing Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 90. All tests were conducted using measurement procedure from ANSI TIA/EIA-603-E-2016 as appropriate. Test Name Test Method/Standard Result Comments RF Output Power 2.1046; 90.205 Pass Modulation Characteristics 2.1047(a) Pass The EUT does not transmit voice. The device transmit data signal only Occupied Bandwidth 2.1049; 90.210 Pass EUT Meets Mask D Spurious Emissions at Antenna Terminals 2.1051; 90.210 Pass Radiated Spurious Emissions 2.1053; 90.210 Pass Frequency Stability over Temperature Variations 2.1055(a)(1); 90.213 Pass Frequency Stability over Voltage Variations 2.1055(d) Pass Transient Frequency Behavior 90.214 Pass HBCS Report # EMC_17050_1 Rev1 Page 5 of 35 EQUIPMENT CONFIGURATION 1. Overview H.B Compliance Solutions was contracted by Schweizer Electronic to perform testing on the LC- 100 Receiver system under the quotation number Q17031006. This document describes the test setups, test methods, required test equipment, and the test limit criteria used to perform compliance testing of the Schweizer Electronic, LC100-Receiver system. The tests were based on FCC Part 90 Rules. The tests described in this document were formal tests as described with the objective of the testing was to evaluate compliance of the Equipment Under Test (EUT) to the requirements of the aforementioned specifications. Schweizer Electronic should retain a copy of this document and it should be kept on file for at least five years after the manufacturing of the EUT has been permanently discontinued. The results obtained relate only to the item(s) tested. Product Name: LC100-Receiver Model(s) Tested: S01 FCC ID: 2AQQU-01LC100S0 Supply Voltage Input: Primary Power: 24 Vdc Frequency Range: 450MHz to 470MHz No. of Channels:…

Text truncated - open the document above for the full version.

1 | P a g e Test Setup Photos Schweizer Electronic – Project 17050 Test Setup Photo # 1 2 | P a g e Test Setup Photo # 2 3 | P a g e Test Setup Photo # 3 4 | P a g e Test Setup Photo # 4 5 | P a g e Test Setup Photo # 5