2AQXW375UTRemote Control

1。pen the remote control by sliding the battery cover down. Press and hold the program button until the LED lights (approximately 2 seconds). 3 LED Program Button Press the program button again to exit programming mode. Programming 1s now complete Program Button 5 Press the programmed button to activate your opener.the garage door opener lights will flash or two clicks are heard.If opener does not activate,repeat the above programming steps again REMOTE CONTROL BATTERY A WARNING To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 3V CR2032 coin batteries. • DO NOT recharge, disassemble, heat above 212 ° F (100 ° C) or incinerate. MODEL 375UT UNIVERSAL REMOTE CONTROL 2 Press and release the Remote Control button you wish to use,the number of times...that corresponds with the below garage door opener type Press Times: Garage Door Opener Type: ...1 time Chamberlain ® * Yellow Button 2011-Current ... 2 times Chamberlain ® * Purple Button 2005-Current ...3 times Chamberlain ® * Orange or Red Button 1997-2005 ...4 times Chamberlain ® * Green Button 1993-1996 ...5 times Genie Overhead Doo卢lntellicode1995-Current 315mhz ...6 times Genie Overhead Doo产lntellicode2005-Current 390mhz ...7 times L inea产Mega-Code 1997-Current ...8 times Wa yne Dalton ® Rolling Code 1999-Current ... 9 times Linear Multicode ® 10 Position Dip Switch ... 10 times Linear ® Dalta 8 Position Dip Switch 310mhz ... 11 times Stanley Multicode ® 10 Position Dip Switch 310mhz ... 12 times Genie ® 9 Position Dip Switch 390mhz ... 13 times Genie ® 12 Position Dip Switch 1985 390mhz ... 14 times Chamberlain ® * 9 Position Dip Switch 1990-1992 390mhz *LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with Chamberlain technology. 4 Press and release the SMART/LEARN button on your garage door opener or gate opener OR RADIO LOGIC BOARD BUTTON Match the remote control DIP SWITCHES to the existing receiver or existing remote control. RECEIVER DIP SWITCHES REMOTE NOTE: The SMART/LEARN button or DIP SWITCHES are located either on the product or in an external receiver on or near the product. Consult your product owner's manual to locate the SMART/LEARN button or DIP SWITCHES. NOTE: If you have a 2 posi打onDIP SWITCH and programming fails, reverse DIP SWITCHES (OFF to ON and ON to OFF). LED Button 2 Button 1 Program Button FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED 2022.03.29 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Remote control Trademark: N/A MODEL : 375UT FCC ID: 2AQXW375UT To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : frank king/Manager Contact information / address: no.28 tianshan road changzhou city jiangsu province china

SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED 2022.03.29 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : frank king/Manager Contact information / address: no.28 tianshan road changzhou city jiangsu province china

Label & label location 20 mm*10mm FCC ID: 2AQXW375UT Label location

Internal Photos Antenna Antenna

No.：BCTC/RF-EMC-00 5 Page: 1 of 44 Edition：A.4 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2203386778E Applicant: SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Product Name: Remote control Model/Type Ref.: 375UT Tested Date: 2022-03-09 to 2022-03-26 Issued Date: 2022-03-26 Report No.: BCTC2203386778E No.：BCTC/RF-EMC-00 5 Page: 2 of 44 Edition：A.4 FCC ID: 2AQXW375UT The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: Remote control Trademark: N/A Model/Type Ref.: 375UT Prepared For: SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address: no.28 tianshan road changzhou city jiangsu province china Manufacturer: SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address: no.28 tianshan road changzhou city jiangsu province china Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2022-03-09 Sample tested Date: 2022-03-09 to 2022-03-26 Issue Date: 2022-03-26 Report No.: BCTC2203386778E Test Standards: FCC Part15.231 ANSI C63.10-2013 Test Results: PASS Tested by: Approved by: Jeff.Fu/Project Handler Zero Zhou/Reviewer Report No.: BCTC2203386778E No.：BCTC/RF-EMC-00 5 Page: 3 of 44 Edition：A.4 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Test Summary ....................................................................................................... 5 3. Measurement Uncertainty ..................................................................................... 6 4. Product Information And Test Setup ..................................................................... 7 4.1 Product Information ............................................................................................... 7 4.2 Test Setup Configuration ...................................................................................... 7 4.3 Support Equipment ............................................................................................... 7 4.4 Channel List .......................................................................................................... 8 4.5 Test Mode ............................................................................................................. 8 5. Test Facility And Test Instrument Used ................................................................. 9 5.1 Test Facility ........................................................................................................... 9 5.2 Test Instrument Used ............................................................................................ 9 6. Conducted Emissions .......................................................................................... 11 6.1 Block Diagram Of Test Setup .............................................................................. 11 6.2 Limit .................................................................................................................... 11 6.3 Test Procedure ................................................................................................... 11 6.4 EUT Operating Conditions .................................................................................. 12 6.5 Test Result .......................................................................................................... 12 7. Radiated Emissions ............................................................................................. 13 7.1 Block Diagram Of Test Setup .............................................................................. 13 7.2 Limit .................................................................................................................... 14 7.3 Test Procedure ................................................................................................... 15 7.4 EUT Operating Conditions .................................................................................. 16 7.5 Test Result .......................................................................................................... 17 8. Bandwidth Test .................................................................................................... 27 8.1 Block Diagram Of Test Setup .............................................................................. 27 8.2 Limit .................................................................................................................... 27 8.3 Test Procedure ................................................................................................... 27 8.4 EUT Operating Conditions .................................................................................. 27 8.5 Test Result .......................................................................................................... 28 9. Calculation Of Average Factor ............................................................................ 31 10. Dwell Time ........................................................................................................... 37 10.1 Block Diagram Of Test Setup ............................................................................ 37 10.2 Limit .................................................................................................................. 37 10.3 Test Procedure ................................................................................................. 37 10.4 Test Result ........................................................................................................ 38 11. Antenna Requirement …

Text truncated - open the document above for the full version.

Report No.: BCTC2203386778E No.：BCTC/RF-EMC-00 5 Page: 43 of 44 Edition：A.4 13. EUT Test Setup Photographs Radiated Measurement Photos