2AQYP-TRACK1100TRACK1100

www.sensolus.com | [email protected] TRACK 1100 Installation and activation manual Other installation methods For alternative fixation methods such as magnets, glue and double sided tape or tie wraps please contact the Sensolus Help Desk. [email protected] or +32.9.298.09.43 Install the tracker with bolts Bolt M6Spring washerWasher Nut 1. Use the appropriate size of screws, it is recommended to use the M6 type and to use thread locking glue on the bolts. We recommend Loctite Thread Locker Blue 242. 2. Protect the tracker casing appropriately: protect the casing with a washer and use a spring washer to mitigate the effects of vibration and temperature variations. 3. Don’t apply too much torque during the fixation: the maximum allowed torque is 3.5NM for an M6 screw used with a washer. Applying more torque may severely damage the tracker’s casing. Rivets diameter 5mmDrilled hole min 5.1 mm Use the appropriate size of rivets. Choose the right length of the rivets. The height of the casing where the mounting holes are located is 8mm. We recommended to use rivets with a diameter of 5mm. Install the tracker with rivets Installation advice Avoid blocking the tracker’s view with metal or carbonfibre walls. They weaken or block the radiofrequency signals. Install the tracker vertically, with the logo facing up. If you can't install vertically, do not mount the tracker upside down. Place the tracker has high as possible on the asset to ensure good network coverage. Make sure the tracker has a clear view on the sky. Do not install the tracker on parts that receive frequent shocks or vibrations. If your asset is handled in a rough environment, you can place the tracker in a protected location, but never with metal or carbonfibre above the tracker. Avoid placing the tracker in a place that can collect water. Make sure the mounting surface is flat and clean, for a strong and durable bond. www.sensolus.com | [email protected] Hold a magnet for about 5 seconds on top of the logo on the asset tracker. You will first see a red LED. Do not remove the magnet yet. When the green LED is blinking you can remove the magnet. Your tracker is ready for use. Troubleshooting Activation of the trackers is preferably done with clear skies, and not inside (e.g. factory or warehouse). Trackers are not activated when delivered to your premises. Their subscription in the platform will start within six month of purchase. Tracker activation 1. Put the magnet on the tracker for less than 5 seconds 2. The possible LED feedback options are: Red LED: Tracker is not activated Green LED: Tracker is activated and working properly No LED: tracker is not functioning (probably dead battery -> contact support) Red LED is blinking: Tracker is busy Force new configuration download on the tracker Hold a magnet for about 5 seconds on top of the logo on the asset tracker. You will see a green LED. You will see a red and green LED. Now remove the Magnet Green LED is blinking for minimum 30 seconds. Your tracker is checking for new configurations You see a red LED: No new configuration received You see a green LED: New configuration setting received Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal- lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Sensolus NV Rijsenbergstraat 148D, 9000 Gent, Belgium TEL: +32 92981393 FAX: +32 92981393 Date: 2022-03-17 FCC ID: 2AQYP-TRACK1100 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Part list Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Koen Van Vlaenderen / VP Production / Co-Founder Sensolus NV Tel: +32486929594 Fax: +32 92981393 E-mail: [email protected]

Sensolus NV Rijsenbergstraat 148D, 9000 Gent, Belgium TEL: +32 92981393 FAX: +32 92981393 Date: 2022-03-17 FCC ID: 2AQYP-TRACK1100 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Sensolus NV hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on Sensolus NV’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------- Koen Van Vlaenderen / VP Production / Co-Founder Sensolus NV Tel: +32486929594 Fax: +32 92981393 E-mail: [email protected]

Reference No.: BCYD-WTW-P21090659_EXT Page 1/3 CONSTRUCTION PHOTOS OF EUT Reference No.: BCYD-WTW-P21090659_EXT Page 2/3 Reference No.: BCYD-WTW-P21090659_EXT Page 3/3

Reference No.: BCYD-WTW-P21090659_INT Page 1/7 CONSTRUCTION PHOTOS OF EUT Reference No.: BCYD-WTW-P21090659_INT Page 2/7 Reference No.: BCYD-WTW-P21090659_INT Page 3/7 Reference No.: BCYD-WTW-P21090659_INT Page 4/7 Reference No.: BCYD-WTW-P21090659_INT Page 5/7 Reference No.: BCYD-WTW-P21090659_INT Page 6/7 Reference No.: BCYD-WTW-P21090659_INT Page 7/7

Report No.: SABCYD-WTW-P21090659 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SABCYD-WTW-P21090659 FCC ID: 2AQYP-TRACK1100 Test Model: SNT3.5 ULTRA Received Date: Oct. 08, 2021 Test Date: Dec. 06, 2021 ~ May 28, 2022 Issued Date: May 30, 2022 Applicant: Sensolus NV Address: Rijsenbergstraat 148D, 9000 Gent, Belgium Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Designation Number: 281270 / TW0032 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth ourfindings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SABCYD-WTW-P21090659 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SABCYD-WTW-P21090659 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SABCYD-WTW-P21090659 Original release May 30, 2022 Report No.: SABCYD-WTW-P21090659 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: TRACK1100 Brand: sensolus Test Model: SNT3.5 ULTRA Sample Status: Mass Production Applicant: Sensolus NV Test Date: Dec. 06, 2021 ~ May 28, 2022 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:May 30, 2022 Celine Chou / Senior Specialist Approved by : , Date:May 30, 2022 Jeremy Lin / Project Engineer Report No.: SABCYD-WTW-P21090659 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SABCYD-WTW-P21090659 Page No. 6 / 6 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Mode Max AV Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) Bluetooth LE 2.30 2.33 20 0.001 1.00 Note: 1. Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 2. The above Antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Mode Max ERP Power (dBm) Max EIRP Power (dBm) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) NB-IoT Band 2 - 26.32 20 0.085 1.00 NB-IoT Band 4 - 26.33 20 0.085 1.00 NB-IoT Band 12 22.68 24.83 20 0.060 0.46 NB-IoT Band 13 22.12 24.27 20 0.053 0.51 Note: …

Text truncated - open the document above for the full version.

Report No.: RFBCYD-WTW-P21090659-1 Page No. 1 / 47 Report Format Version: 6.1.1 FCC Test Report (Part 24 – NB-IoT B2) Report No.: RFBCYD-WTW-P21090659-1 FCC ID: 2AQYP-TRACK1100 Test Model: SNT3.5 ULTRA Received Date: Oct. 08, 2021 Test Date: Dec. 09, 2021 ~ May 26, 2022 Issued Date: May 30, 2022 Applicant: Sensolus NV Address: Rijsenbergstraat 148D, 9000 Gent, Belgium Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Designation Number: 281270 / TW0032 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RFBCYD-WTW-P21090659-1 Page No. 2 / 47 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Test Site and Instruments .................................................................................................................... 7 3 General Information .............................................................................................................................. 8 3.1 General Description of EUT ................................................................................................................ 8 3.2 Configuration of System under Test .................................................................................................. 10 3.2.1 Description of Support Units .............................................................................................................. 10 3.3 Test Mode Applicability and Tested Channel Detail ........................................................................... 11 3.4 EUT Operating Conditions ................................................................................................................ 15 3.5 General Description of Applied Standards and References ............................................................. 15 4 Test Types and Results ...................................................................................................................... 16 4.1 Output Power Measurement ............................................................................................................. 16 4.1.1 Limits of Output Power Measurement ............................................................................................... 16 4.1.2 Test Procedures ................................................................................................................................. 16 4.1.3 Test Setup .......................................................................................................................................... 16 4.1.4 Test Results ....................................................................................................................................... 17 4.2 Modulation Characteristics Measurement ......................................................................................... 27 4.2.1 Limits of Modulation Characteristics .................................................................................................. 27 4.2.2 Test Procedure .................................................................................................................................. 27 4.2.3 Test Setup .......................................................................................................................................... 27 4.2.4 Test Results ....................................................................................................................................... 27 4.3 Frequency Stability Measurement .................................................................................................... 28 4.3.1 Limits of Frequency Stabiliity Measurement ..................................................................................... 28 4.3.2 Test Procedure .....................................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBCYD-WTW-P21090659-2 Page No. 1 / 103 Report Format Version: 6.1.1 FCC Test Report (Part 27 – NB-IoT B4/B12/B13) Report No.: RFBCYD-WTW-P21090659-2 FCC ID: 2AQYP-TRACK1100 Test Model: SNT3.5 ULTRA Received Date: Oct. 08, 2021 Test Date: Dec. 09, 2021 ~ May 28, 2022 Issued Date: May 30, 2022 Applicant: Sensolus NV Address: Rijsenbergstraat 148D, 9000 Gent, Belgium Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Designation Number: 281270 / TW0032 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RFBCYD-WTW-P21090659-2 Page No. 2 / 103 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 7 2.2 Test Site and Instruments .................................................................................................................... 8 3 General Information .............................................................................................................................. 9 3.1 General Description of EUT ................................................................................................................ 9 3.2 Configuration of System under Test .................................................................................................. 13 3.2.1 Description of Support Units .............................................................................................................. 13 3.3 Test Mode Applicability and Tested Channel Detail .......................................................................... 14 3.4 EUT Operating Conditions ................................................................................................................ 24 3.5 General Description of Applied Standards and References ............................................................. 24 4 Test Types and Results ...................................................................................................................... 25 4.1 Output Power Measurement ............................................................................................................. 25 4.1.1 Limits of Output Power Measurement ............................................................................................... 25 4.1.2 Test Procedures ................................................................................................................................. 25 4.1.3 Test Setup .......................................................................................................................................... 25 4.1.4 Test Results ....................................................................................................................................... 26 4.2 Modulation Characteristics Measurement ......................................................................................... 56 4.2.1 Limits of Modulation Characteristics .................................................................................................. 56 4.2.2 Test Procedure .................................................................................................................................. 56 4.2.3 Test Setup .......................................................................................................................................... 56 4.2.4 Test Results ....................................................................................................................................... 56 4.3 Frequency Stability Measurement .................................................................................................... 58 4.3.1 Limits of Frequency Stability Measurement ...................................................................................... 58 4.3.2 Test Procedure ............................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBCYD-WTW-P21090659-2 Page No. 78 / 103 Report Format Version: 6.1.1 4.7.4 Test Results NB-IoT Band 4, Subcarrier Spacing 3.5kHz Channel 19952 (1710.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz Channel 20175 (1732.5MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz Channel 20398 (1754.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 79 / 103 Report Format Version: 6.1.1 NB-IoT Band 4, Subcarrier Spacing 15kHz Channel 19952 (1710.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz Channel 20175 (1732.5MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz Channel 20398 (1754.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 20GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 80 / 103 Report Format Version: 6.1.1 NB-IoT Band 12, Subcarrier Spacing 3.5kHz Channel 23012 (699.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz Channel 23095 (707.5MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz Channel 23178 (715.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 81 / 103 Report Format Version: 6.1.1 NB-IoT Band 12, Subcarrier Spacing 15kHz Channel 23012 (699.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz Channel 23095 (707.5MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz Channel 23178 (715.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 10GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 82 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 3.5kHz Channel 23182 (777.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 83 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 3.5kHz Channel 23230 (782.0MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 84 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 3.5kHz Channel 23278 (786.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 85 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 15kHz Channel 23182 (777.2MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 86 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 15kHz Channel 23230 (782.0MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 87 / 103 Report Format Version: 6.1.1 NB-IoT Band 13, Subcarrier Spacing 15kHz Channel 23278 (786.8MHz) Frequency Range : 9kHz ~ 1GHz Frequency Range : 1GHz ~ 1.559GHz Frequency Range : 1.559GHz ~ 1.61GHz Frequency Range : 1.61GHz ~ 8GHz *The 9kHz signal over the limit is from Spectrum. Report No.: RFBCYD-WTW-P21090659-2 Page No. 88 / 103 Report Format Version: 6.1.1 4.8 Radiated Emission Measurement 4.8.1 Limits of Radiated Emission Measurement For NB-IoT Band 4: According to FCC 27.53(h), for operations in the 1695-1710MHz, 1710-1755MHz, 1755-1780 MHz bands, the power of any emission outside a licensee's frequency block shall be attenuated below the transmitter power (P) in watts by at least 43 + 10 log (P) dB. For NB-IoT Band 12: According to FCC 27.53(g), for opera…

Text truncated - open the document above for the full version.