2AQYQ-NOVAPAD-PROComputer tablet

FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. *RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. SAR Statement: SAR tests are conducted using standard operating positions according standards with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This model product has been tested and meets the RF exposure guidelines with the test distan ce 0mm for body worn. The highest SAR19 value is 0.617 W/Kg for body worn. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided ISED Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:: (1) This device may not cause interference; and (2) This device must ac cept any inte rference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux RSS sans licence d’Industrie Canada. L’exploitation est soumise aux deux conditions suivantes : (1)Ce dispositif ne peut causer d'interférences ; et (2)Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. RF Exposure Statement SAR Statement: SAR tests are conducted using standard operating positions according standards withthe device transmitting at its highest certified power level in all tested frequency bands,although the SAR is determined at the highest certified power level, the actual SARlevel of the device while operating can be well below the maximum value.This model product has been tested and meets the RF exposure guidelines with thetest distance Omm for body worn. The highest SAR1g value is 0.617 W/Kg for bodyworn. The use of belt clips, holsters and similar accessories should not containmetallic components in its assembly. The use of accessories that do not satisfy theserequirements may not comply with RF exposure requirements, and should beavoided Les tests DAS sont effectués dans des positions d'utilisation standard, conformément aux normes, l'appareil émettant à sa puissance maximale certifiée dans toutes les bandes de fréquences testées. Bien que le DAS soit déterminé à la puissance maximale certifiée, le niveau DAS réel de l'appareil en fonctionnement peut être nettement inférieur à cette valeur maximale. Ce modèle a été testé et est conforme aux directives d'exposition aux radiofréquences (RF) à une distance d'essai de 0 mm pour un port sur le corps. La valeur DAS1g maximale est de 0,617 W/kg pour un port sur le corps. Les attaches de ceinture, étuis et accessoires similaires ne doivent pas comporter de composants métalliques. L'utilisation d'accessoires non conformes à ces exigences peut entraîner une non-conformité aux exigences d'exposition aux RF et devrait être évitée. The device is restricted to indoor use only when operating in the 5150to 5250MHz frequency range. L'appareil est limite a une utilisation interieure uniquement lorsqu'ilfonctionne dans la plage de frequences de 5 150 a 5250 MHz.

Page 1 of 86 Report No.: AiTSZ-260127032FW5 FCC SAR EVALUATION REPORT In accordance with the requirements of FCC 47 CFR Part 2(2.1093) and IEEE Std 1528-2013 Product Name: Computer tablet Model No.: NovaPad Pro Serial Model: N/A Brand Name: Report No.: AiTSZ-260127032FW5 FCC ID: 2AQYQ-NOVAPAD-PRO Prepared for HeYuan Vastking Electronic Co., Ltd No.13, Hepu Avenue, Yuancheng District, Heyuan City, Guangdong Province, China Prepared by Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Page 2 of 86 Report No.: AiTSZ-260127032FW5 TEST RESULT CERTIFICATION Applicant’s name..................:HeYuan Vastking Electronic Co., Ltd Address..................................: No.13, Hepu Avenue, Yuancheng District, Heyuan City, Guangdong Province, China Manufacturer's Name...........:HeYuan Vastking Electronic Co., Ltd Address..................................: No.13, Hepu Avenue, Yuancheng District, Heyuan City, Guangdong Province, China Product description Product name.........................: Computer tablet Trademark .............................: Model and/or type reference ..: NovaPad Pro Serial Model............................: N/A Standards..............................: FCC 47 CFR Part 2(2.1093) IEEE Std 1528-2013 Published RF exposure KDB procedures This device described above has been tested by Guangdong Asia Hongke Test Technology Limited. In accordance with the measurement methods and procedures specified in IEEE Std 1528-2013 and KDB 865664 D01.Testing has shown that this device is capable of compliance with localized specific absorption rate (SAR) specified in FCC 47 CFR Part 2(2.1093). The test results in this report apply only to the tested sample of the stated device/equipment. Other similar device/equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. Test Sample Number ..............................:AiTSZ-260127032-1 Date of Test Date (s) of performance of tests .............:Jan. 27, 2026 ~ Feb. 06, 2026 Date of Issue...........................................:Feb. 06, 2026 Test Result ..............................................:Pass Reviewed by: Approved by: Ken Zou Jack Li Page 3 of 86 Report No.: AiTSZ-260127032FW5 ※ ※ Revision History ※ ※ REV.DESCRIPTIONISSUED DATEREMARK Rev.1.0Initial Test Report ReleaseFeb. 06, 2026Jack Li Page 4 of 86 Report No.: AiTSZ-260127032FW5 TABLE OF CONTENTS 1.General Information............................................................................................6 1.1.RF exposure limits....................................................................................6 1.2.Statement of Compliance........................................................................7 1.3.EUT Description.......................................................................................8 1.4.Test specification(s)..................................................................................9 1.5.Ambient Condition...................................................................................9 1.6.Test Facility..............................................................................................9 2.SAR Measurement System.................................................................................10 2.1.SATIMO SAR Measurement Set-up Diagram.........................................10 2.2.Robot.....................................................................................................11 2.3.Probe......................................................................................................12 2.3.1.E-Field Probe Calibration.................................................................12 2.4.Phantoms...............................................................................................13 2.5.Technical Data........................................................................................14 2.6.Device Holder.........................................................................................15 2.7.Test Equipment List................................................................................16 3.SAR Measurement Procedures..........................................................................19 3.1.Power Reference....................................................................................19 3.2.Area scan & Zoom scan..........................................................................19 3.3.Description of interpolation/extrapolation scheme..............................21 3.4.Volumetric Scan.....................................................................................21 3.5.Power Drift.............................................................................................21 4.System Verification Procedure...........................................................................22 4.1.Tissue Verification..................................................................................22 4.1.1.Tissue Dielectric Parameter Check Results......................................23 4.2.System Verification Procedure..............................................................24 4.2.1.System Verification Results.............................................................25 5.SAR measurement variabilit...............................................................................26 6.SAR Measurement Uncertainty.........................................................................27 7.RF Exposure Positions..........................................................…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2AQYQ-NOVAPAD-PRO Page 2 of 2 FCC ID: 2AQYQ-NOVAPAD-PRO

FCC ID: 2AQYQ-NOVAPAD-PRO Back Side (Separation distance of 0mm) Top Side (Separation distance of 0mm)

Page 1 of 51 Report No.: AiTSZ-260127032FW1 Appendix RF test data for BT Page 2 of 51 Report No.: AiTSZ-260127032FW1 1. Bandwidth 1.1 Test Result 1.1.1 OBW 99% Occupied Bandwidth (MHz) Mode TX Type Frequency (MHz) Packet Type ANT ResultLimit Verdict 2402DH510.864/Pass 2441DH510.845/Pass GFSKSISO 2480DH510.876/Pass 24022DH511.185/Pass 24412DH511.179/Pass Pi/4DQPSKSISO 24802DH511.186/Pass 24023DH511.189/Pass 24413DH511.188/Pass 8DPSKSISO 24803DH511.188/Pass 1.1.2 20dB BW 20dB Bandwidth (MHz) Mode TX Type Frequency (MHz) Packet Type ANT ResultLimit Verdict 2402DH510.960/Pass 2441DH510.962/Pass GFSKSISO 2480DH510.961/Pass 24022DH511.292/Pass 24412DH511.294/Pass Pi/4DQPSKSISO 24802DH511.291/Pass 24023DH511.315/Pass 24413DH511.307/Pass 8DPSKSISO 24803DH511.308/Pass Page 3 of 51 Report No.: AiTSZ-260127032FW1 1.2 Test Graph 1.2.1 OBW GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 4 of 51 Report No.: AiTSZ-260127032FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 5 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 6 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 7 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 8 of 51 Report No.: AiTSZ-260127032FW1 1.2.2 20dB BW GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 9 of 51 Report No.: AiTSZ-260127032FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 10 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 11 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 12 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 13 of 51 Report No.: AiTSZ-260127032FW1 2. Maximum Conducted Output Power 2.1 Test Result 2.1.1 Power Maximum Peak Conducted Output Power (dBm) Mode TX Type Frequency (MHz) Packet Type ANT1Limit Verdict 2402DH5-0.44<=30Pass 2441DH51.88<=30Pass GFSKSISO 2480DH50.60<=30Pass 24022DH51.66<=20.97Pass 24412DH54.01<=20.97Pass Pi/4DQPSKSISO 24802DH52.77<=20.97Pass 24023DH51.94<=20.97Pass 24413DH54.24<=20.97Pass 8DPSKSISO 24803DH52.88<=20.97Pass Note1: Antenna Gain: Ant1: 0.04Bi; Page 14 of 51 Report No.: AiTSZ-260127032FW1 2.2 Test Graph 2.2.1 Power GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 15 of 51 Report No.: AiTSZ-260127032FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 16 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 17 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 18 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 19 of 51 Report No.: AiTSZ-260127032FW1 3. Carrier Frequency Separation 3.1 Test Result 3.1.1 Ant1 Ant1 Mode TX Type Frequency (MHz) Packet Type Channel Separation (MHz) 20dB Bandwidth (MHz) Limit (MHz) Verdict GFSKSISOHOPPDH50.9940.962>=0.962Pass Pi/4DQPSKSISOHOPP2DH50.9981.294>=0.863Pass 8DPSKSISOHOPP3DH51.0101.315>=0.877Pass Page 20 of 51 Report No.: AiTSZ-260127032FW1 3.2 Test Graph 3.2.1 Ant1 GFSK_DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 21 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HOPP_Ant1_NTNV Page 22 of 51 Report No.: AiTSZ-260127032FW1 4. Number of Hopping Frequencies 4.1 Test Result 4.1.1 HoppNum Num of Hopping Frequencies Mode TX Type Frequency (MHz) Packet Type ANT1Limit Verdict GFSKSISOHOPPDH579>=15Pass Pi/4DQPSKSISOHOPP2DH579>=15Pass 8DPSKSISOHOPP3DH579>=15Pass Page 23 of 51 Report No.: AiTSZ-260127032FW1 4.2 Test Graph 4.2.1 HoppNum GFSK_DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 24 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HOPP_Ant1_NTNV Page 25 of 51 Report No.: AiTSZ-260127032FW1 5. Time of Occupancy (Dwell Time) 5.1 Test Result 5.1.1 Ant1 Ant1 Mode TX Type Frequency (MHz) Packet Type Duration of Single Pulse (ms) Observation Period (s) Num of Pulse in Observation Period Dwell Time (ms) Limit (ms) Verdict DH10.41031.600320131.200<=400Pass DH31.68431.600163274.492<=400Pass GFSKSISOHOPP DH52.93031.600112328.160<=400Pass 2DH10.42031.600320134.400<=400Pass 2DH31.67231.600154257.488<=400Pass Pi/4DQPSKSISOHOPP 2DH52.92031.600102297.840<=400Pass 3DH10.40031.600320128.000<=400Pass 3DH31.65031.600153252.450<=400Pass 8DPSKSISOHOPP 3DH52.91631.600107312.012<=400Pass Page 26 of 51 Report No.: AiTSZ-260127032FW1 5.2 Test Graph 5.2.1 Ant1 GFSK_DH1_HOPP_Ant1_NTNV GFSK_DH1_HOPP_Ant1_NTNV Page 27 of 51 Report No.: AiTSZ-260127032FW1 GFSK_DH3_HOPP_Ant1_NTNV GFSK_DH3_HOPP_Ant1_NTNV Page 28 of 51 Report No.: AiTSZ-260127032FW1 GFSK_DH5_HOPP_Ant1_NTNV GFSK_DH5_HOPP_Ant1_NTNV Page 29 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH1_HOPP_Ant1_NTNV Pi/4DQPSK_2DH1_HOPP_Ant1_NTNV Page 30 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH3_HOPP_Ant1_NTNV Pi/4DQPSK_2DH3_HOPP_Ant1_NTNV Page 31 of 51 Report No.: AiTSZ-260127032FW1 Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 32 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH1_HOPP_Ant1_NTNV 8DPSK_3DH1_HOPP_Ant1_NTNV Page 33 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH3_HOPP_Ant1_NTNV 8DPSK_3DH3_HOPP_Ant1_NTNV Page 34 of 51 Report No.: AiTSZ-260127032FW1 8DPSK_3DH5_HOPP_Ant1_NTNV 8DPSK_3DH5_HOPP_Ant1_NTNV Page 35 of 51 Report No.: AiTSZ-260127032FW1 6. Unwanted Emissions In Non-restricted Frequency Bands 6.1 Test Result 6.1.1 Ref Mode TX Type Frequency (MHz) Packet Type ANT Level of Reference (dBm) 2402DH51-0.56 2441DH511.79 GFSKSISO 2480DH510.46 24022DH51-0.51 24412DH511.81 Pi/4DQPSKSISO 24802DH510.64 24023DH51-0.52 24413DH511.78 8DPSKSISO 24803DH510.48 Note1: Refer to FCC Part 15.247 (d) and ANSI C63.10-2020, the channel contains the maximum PSD level was used to establish the reference level. 6.1.2 CSE Mode TX Type Frequency (MHz) Packet Type AN…

Text truncated - open the document above for the full version.

Page 1 of 36 Report No.: AiTSZ-260127032FW1 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. TEST REPORT Product Name:Computer tablet Brand Name: Model: NovaPad Pro Series Model: NovaPad Pro********** FCC ID: 2AQYQ-NOVAPAD-PRO Applicant:HeYuan Vastking Electronic Co., Ltd Address: No.13, Hepu Avenue, Yuancheng District, Heyuan City, Guangdong Province, China Manufacturer:HeYuan Vastking Electronic Co., Ltd Address: No.13, Hepu Avenue, Yuancheng District, Heyuan City, Guangdong Province, China Standard(s):FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of Receipt:Jan. 27, 2026 Date of Test:Jan. 27, 2026~ Feb. 06, 2026 Issued Date:Apr. 13, 2026 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Aalen.Ye Allen Wang Page 2 of 36 Report No.: AiTSZ-260127032FW1 Report Revise Record Report VersionIssued DateNotes M0Apr. 13, 2026Initial Release Page 3 of 36 Report No.: AiTSZ-260127032FW1 Contents 1TEST SUMMARY......................................................................................................................................................4 1.1TEST STANDARDS.........................................................................................................................................................4 1.2TEST SUMMARY...........................................................................................................................................................4 1.3TEST FACILITY..............................................................................................................................................................5 1.4MEASUREMENT UNCERTAINTY........................................................................................................................................5 2GENERAL INFORMATION........................................................................................................................................6 2.1ENVIRONMENTAL CONDITIONS........................................................................................................................................6 2.2GENERAL DESCRIPTION OF EUT......................................................................................................................................6 2.3DESCRIPTION OF TEST MODES AND TEST FREQUENCY.........................................................................................................7 2.4SPECIAL ACCESSORIES...................................................................................................................................................8 2.5EQUIPMENT LIST FOR THE TEST.......................................................................................................................................8 3TEST CONDITIONS AND RESULTS...........................................................................................................................10 3.1CONDUCTED EMISSIONS TEST.......................................................................................................................................10 3.2RADIATED EMISSIONS AND BAND EDGE..........................................................................................................................13 3.3MAXIMUM PEAK OUTPUT POWER................................................................................................................................20 3.420DB BANDWIDTH....................................................................................................................................................21 3.5OCCUPIED BANDWIDTH...............................................................................................................................................22 3.6FREQUENCY SEPARATION.............................................................................................................................................23 3.7NUMBER OF HOPPING FREQUENCY................................................................................................................................24 3.8TIME OF OCCUPANCY (DWELL TIME) .............................................................................................................................25 3.9OUT-OF-BAND EMISSIONS...........................................................................................................................................26 3.10PSEUDORANDOM FREQUENCY HOPPING SEQUENCE..........................................................................................................28 3.11ANTENNA REQUIREMENT.............................................................................................................................................29 4TEST SETUP PHOTOGRAPHS OF EUT......................................................................................................................30 5PHOTOS OF EUT...................................................................................................................................................…

Text truncated - open the document above for the full version.

Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Customer Nam：Vastking Project Name: M50-B-12.7" Metal Enclosure - English Keyboard T30 Motherboard - T7300 Main Controller Date：2026.01.28 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Customer contact person: mobile phone: Email: Soward RF: Xiao Chunyan mobile phone: Phone: 0755-29985185 Email: [email protected] Soward structure: mobile phone: Phone: 0755-29985185 Email: [email protected] Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen 1.Project Brief Number of project antennas Machine type 1tablet Whole machine casing material: 12.7-inch metal shell 2.Antenna Overview Antenna number nameWorking frequency band/MHz Material/Struct ure 1WIFI&GPS&BT&5Gwifi2400MHz/2500MHz & 1575MHz & 5.8GHzFPC Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen GPS&WIFI&BT anttern Antenna layout Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI&GPS&BT antenna S11 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WiFi throughput Iperf throughput test model M50-B -English card T30 motherboard - T7300 main control module Accompanyin g the motherboard software version IPerf2 for Android Model Number frequency banddistanceTest angle test data (TX) 1-minute mean test data (RX) 1-minute mean remark (Number of packet drops) 1 2.4G 5G 2.4G WIFI （Research and development 15m） 0°93.6 Mpbs21.2 Mpbs0 90°96.1 Mpbs21.8 Mpbs0 019.3 Mpbs93.6 Mpbs180° 270°97.4 Mpbs19.1 Mpbs0 0°293 Mpbs235 Mpbs 5F WIFI （Research and development 15m） 0 0238 Mpbs295 Mpbs90° 180°301 Mpbs225 Mpbs0 0228 Mpbs300 Mpbs270° Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI antenna throughput test (test image) Test data uploaded via 2.4GHz WiFi (corresponding to a connection speed of 162Mbps) Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen BT antenna measured distance Actual test effect Model Number1 test environment Soward R&D Center test equipment Huawei AM08 test distance> 10 m Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI&BTantenna efficiency Passive Test For 2.4Gwifi FreqEffiEffiGainGainMaxMin (MHz)(%)(dB)(dBi)(dBd)(dB)(dB) 240015.3-8.15-1.91-4.06-1.91-18.06 241016.02-7.95-1.63-3.78-1.63-17.37 242016.93-7.71-1.06-3.21-1.06-17.2 243016.96-7.71-0.67-2.82-0.67-17.35 244016.77-7.76-0.36-2.51-0.36-18.3 245017.79-7.50.04-2.110.04-19.33 246017.24-7.64-0.05-2.2-0.05-21.88 247017.33-7.610-2.150-20.61 248016.84-7.740-2.150-21.04 249016.61-7.80.05-2.10.05-23.6 250014.33-8.44-0.71-2.86-0.71-22.03 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen 5GWIFIantenna efficiency Passive Test For 5Gwifi FreqEffiEffiGainGainMaxMin (MHz)(%)(dB)(dBi)(dBd)(dB)(dB) 5000 7.01-11.55 3.321.173.32-21.86 5100 8.91-10.5 3.271.123.27-22.57 5200 12.02-9.2 1.95-0.21.95-21.48 5300 16.75-7.76 2.04-0.112.04-15.64 5400 17.59-7.55 2.13-0.022.13-14.63 5500 17.89-7.47 1.09-1.061.09-14.24 5600 19.72-7.05 2.170.022.17-15.13 5700 23.45-6.3 2.13-0.022.13-18.21 5800 20.68-6.85 1.91-0.241.91-13.87 5900 20.49-6.88 3.10.953.1-11.65 6000 19.67-7.06 2.350.22.35-10.89 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen WIFI antenna signal strength measurement picture (data) Test location: Our R&D office Test time: 14:00-14:30 Test distance: 10-15 meters Signal strength: -51dBm to - 40dBm Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen GPSantenna efficiency Passive Test For GPS2 FreqEffiEffiGainGainMaxMin (MHz)(%)(dB)(dBi)(dBd)(dB)(dB) 157010.02-9.99-4.62-6.77-4.62-22.66 157110.15-9.94-4.55-6.7-4.55-22.6 157210.31-9.87-4.5-6.65-4.5-22.47 157310.51-9.78-4.45-6.6-4.45-22.47 157410.66-9.72-4.41-6.56-4.41-22.38 157510.83-9.65-4.38-6.53-4.38-22.27 157610.99-9.59-4.4-6.55-4.4-22.24 157711.11-9.54-4.38-6.53-4.38-22.26 157811.17-9.52-4.37-6.52-4.37-22.15 157911.3-9.47-4.34-6.49-4.34-22.01 158011.39-9.43-4.3-6.45-4.3-21.79 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen GPS measured images (data) Test location: Our company's rooftop Test time: 10:00 to 10:30 Test direction: East, South, West, North Cold start positioning time: 60 seconds Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Antenna matching Main antenna 123456remark Original Match Change Matching RＦ ２ 1 3 5 4 6 antenna No antenna matching has been changed。 Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Environmental treatment and assembly instructions 1. At the red frame, a conductive sponge is attached below the motherboard to ensure sufficient grounding between the motherboard and the screen; Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Environmental treatment and assembly instructions 未更改环境处理。 2. At the red box, paste conductive cloth to shield some of the circuit on the motherboard at the corresponding position (Attach conductive cloth from the right side of the RF socket to the metal shielding cover on the right side, first insulate and then shield); 3. At the blue frame, a 2mm conductive sponge is attached to the front shielding cover of the motherboard and connected to the screen ground; Building B, Hexi Hangcheng Industrial Zone, No. 135 Qianjin No. 2 Road, Baoan District, Shenzhen Environmental treatment and assembly instructions 未更改环境处理。 4. At the yellow frame, paste conductive foam at the corresponding position on the motherboard to connect the metal shell to the screen ground; 5. At the blue frame, a conduct…

Text truncated - open the document above for the full version.

Page 67 of 86 Report No.: AiTSZ-260127032FW5 Page 68 of 86 Report No.: AiTSZ-260127032FW5 Page 69 of 86 Report No.: AiTSZ-260127032FW5 Page 70 of 86 Report No.: AiTSZ-260127032FW5 Page 71 of 86 Report No.: AiTSZ-260127032FW5 Page 72 of 86 Report No.: AiTSZ-260127032FW5 Page 73 of 86 Report No.: AiTSZ-260127032FW5 Page 74 of 86 Report No.: AiTSZ-260127032FW5 Page 75 of 86 Report No.: AiTSZ-260127032FW5 Page 76 of 86 Report No.: AiTSZ-260127032FW5 Page 77 of 86 Report No.: AiTSZ-260127032FW5 Page 78 of 86 Report No.: AiTSZ-260127032FW5 Page 79 of 86 Report No.: AiTSZ-260127032FW5 Page 80 of 86 Report No.: AiTSZ-260127032FW5 Page 81 of 86 Report No.: AiTSZ-260127…

Text truncated - open the document above for the full version.