2AQZU-18015CEILING FAN REMOTE CONTROLLER

CEILING FAN REMOTE CONTROLLER OPERATION AND INSTALLATION INSTRUCTIONS (Please keep this instruction pamphlet.) IMPORTANT POINTS TO REMEMBER: 1. Read and save these instructions. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch. 4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan. 5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection. 6. This unit is to be used for the control of ceiling fan and in an AC110V/120V 60Hz power supply only. 7. Do not install in damp locations or immerse into water. (For indoor use only.) 8. Do not pull on or cut leads shorter. 9. Do not drop or bump the unit. 10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children. 11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. INSTALLATION INSTRUCTIONS 1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch” after installation. 2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes up to cover the receiver and bracket. 3. For better remote performance with WiFi system, let T-shape antenna stuck on ceiling and outside of the steel canopy. (Fig. 1) IMPORTANT YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL. CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER. CODE SWITCH 1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used for both transmitter and receiver is exactly the same; otherwise remote controller will not work. Please note the code switch will enable you to operate a second remote controller independently. For example, if you have two ceiling fans with 2 remote control units, set 2 different codes for each set of transmitter/receivers. This means you can operate each ceiling fan independently. 2.Your remote control is ready for use after battery (AAA*2PCS)installation. LIGHT FUNCTION SELECT SWITCH If installed energy light onto ceiling fan, please set the “light function select switch” “light function select switch” to on/off position,” CFL”. If installed tungsten light onto ceiling fan, please set the “light function select switch” to dimmer position,” D”. FUNCTIONS OF TRANSMITTER : Turn on or off the light and fan will turn on : fan switches between 1and 4speeds : ON/OFF- Press and release immediately to turn on or off the light. DIMMER- Press and hold on to dimmer or brighten the light. (For the tungsten bulb and “light function select switch” is at D position.) Installation of transmitter wall mount holder with two screws. :Press the button for set fan speed being turned and changed at random. : Press the button the light will do the color temperature switch : Press the button, the fan will enter or cancels 2HR,4HR,8HR timer mode To assure continued FCC compliance: FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: To assure continued FCC compliance: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC ID：2AQZU-18015 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE : Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Reference N Waltek Tes http://www EXHIBI EUT View 1 EUT View 2 No.: WTH20X sting Group w.semtest.co T 2 - EUT 1 2 X08055376W (Shenzhen) m.cn T EXTER W Co., Ltd. RNAL PH HOTOGR APHS Reference N Waltek Tes http://www EUT View 3 EUT View 4 No.: WTH20X sting Group w.semtest.co 3 4 X08055376W (Shenzhen) m.cn W Co., Ltd. Reference N Waltek Tes http://www EUT View 5 EUT View 6 No.: WTH20X sting Group w.semtest.co 5 6 X08055376W (Shenzhen) m.cn W Co., Ltd.

Reference N Waltek Tes http://www EXHIBI Proposed Specificatio n it is visible durable to r expected lif e Proposed No.: WTH20X sting Group w.semtest.co T 1 - PRO FCC ID La ns: The label or easily acc emain fully l etime. Label Loca X08055376W (Shenzhen) m.cn ODUCT L abel Forma shall be secu cessible to th legible and in ation on EU W Co., Ltd. LABELIN at FC urely affixed t he user, and ntact on the UT FCC NG CC ID: 2AQ to a permane shall not be device in al l ID Label Lo QZU-18015 ently attached readily detac l normal cond cation 5 d part of the d chable. The l ditions of use device, in a lo label shall be e throughout ocation where e sufficiently t the device’s e y s

Reference N Waltek Tes http://www EXHIBI EUT Housi n Solder Boa r No.: WTH20X sting Group w.semtest.co T 3 - EUT ng and Boar rd-Compone X08055376W (Shenzhen) m.cn T INTER rd View 1 ent View 1 W Co., Ltd. NAL PHO OTOGRA APHS Reference N Waltek Tes http://www Solder Boa r Solder Boa r No.: WTH20X sting Group w.semtest.co rd-Compone rd-Compone X08055376W (Shenzhen) m.cn ent View 2 ent View 3 W Co., Ltd. SR RD Antenna.

Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Page 1 of 22 TEST REPORT Reference No. .................... : WTH20X08055376W FCC ID ................................ : 2AQZU-18015 Applicant ........................... : Satellite Electronic(Zhong shan)Ltd. Address ............................. : No.8, Chuang Ye Road, Torch Development Zone, Zhongshan, Guangdong, China. Product Name ................... : CEILING FAN REMOTE CONTROLLER Test Model. ........................ : TR227B Standards .......................... : FCC Part 15.231 Date of Receipt sample .... : Aug.13, 2020 Date of Test........................ : Aug.13, 2020 to Aug.21, 2020 Date of Issue ..................... : Aug.21, 2020 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Tested by: Reviewed By: Approved & Authorized By: Jack Huang / Project Engineer Lion Cai / RF Manager Silin Chen / Manager Reference No.: WTH20X08055376W Page 2 of 22 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 6 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 7 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 8 3. ANTENNA REQUIREMENT .................................................................................................................................. 9 3.1 STANDARD APPLICABLE ......................................................................................................................................... 9 3.2 TEST RESULT.......................................................................................................................................................... 9 4. RADIATED EMISSIONS ....................................................................................................................................... 10 4.1 STANDARD APPLICABLE ....................................................................................................................................... 10 4.2 TEST PROCEDURE ................................................................................................................................................. 11 4.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................ 12 4.4 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 12 5. 20DB BANDWIDTH ............................................................................................................................................... 15 5.1 STANDARD APPLICABLE ....................................................................................................................................... 15 5.1 TEST PROCEDURE ................................................................................................................................................. 15 5.2 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 15 6. TRANSMISSION TIME ......................................................................................................................................... 17 6.1 STANDARD APPLICABLE ....................................................................................................................................... 17 6.2 TEST PROCEDURE ................................................................................................................................................. 17 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 17 7. DUTY CYCLE ......................................................................................................................................................... 19 7.1 STANDARD APPLICABLE ....................................................................................................................................... 19 7.2 TEST PROCEDURE ............................................................................................…

Text truncated - open the document above for the full version.

Reference N Waltek Tes http://www EXHIBI Radiation E Radiation E No.: WTH20X sting Group w.semtest.co T 4 - TES Emission Tes Emission Tes X08055376W (Shenzhen) m.cn ST SETUP st Setup (Belo st Setup (30M W Co., Ltd. P PHOTO ow 30MHz) MHz to 1GHz OGRAPH z) HS Reference N Waltek Tes http://www Radiation E Radiation E No.: WTH20X sting Group w.semtest.co Emission Tes Emission Tes X08055376W (Shenzhen) m.cn st Setup (1GH st Setup (Abo W Co., Ltd. Hz to 18GHz ove 18GHz) z) Reference N Waltek Tes http://www No.: WTH20X sting Group w.semtest.co X08055376W (Shenzhen) m.cn W Co., Ltd.