2AR5U-DOCK163129WDOCK163129W

Wireless Charger 10 Watts Max USB Type-C Charger (30W & 60W Max.) USB Type-A Charger (DC 5V 2.1A and 2.4A Max.) Tamper-Resistant AC Receptacle (AC 120V 8A Max. per receptacle) Plug in to a grounded AC outlet only Kensington® NanoSaver™ Lock Slot Please contact with National Lighting Corp. at (888)428-6886 or www.NationalLighting.com for more information. Scepter Quick Reference GuideVersion: 1.0 Model: DOCK163129W Rating: AC 120V, 60Hz, 12A Specifications: 3 x Qi wireless rapid chargers, 3 x Tamper-resistant AC receptacles, 2 x USB Type-A charging ports, 1 x 30W USB Type-C charging port, 1 x 60W USB Type-C charging port. CAUTION: To prevent the risk of fire and electric shock, please be sure to read all instructions before installing or using this unit. DOCK-1600 SERIES QUICK REFERENCE GUIDE Storable temperature (non-operating): -30 °C to 70 °C Typical value: 25 °C Operating temperature Limits: -20 °C to 40 °C Typical value: 25 °C Storage Humidity (non-operating): 5% to 90% RH (Non condensation) Operating Humidity Limits: 10% to 90% RH (Non condensation) Storage Altitude (non-operating): 0 to +2000m above the sea level Operating Altitude (non-operating): 0 to +2000m above the sea level Supports USB PD3.0 charging standard Support PPS charging standard Support QC2.0 / 3.0 charging standard 5.0 Support USB DCP BC1.2 charging standard Support Apple 5W / 10W / 12W USB charging standard Support AFC charging standard Supports FCP charging standard USB output charging can reach 60W maximum. Wireless charging module can wirelessly charge mobile phones at a distance of 0-6mm. The maximum power can reach 10W - Indoor use only - Do not use with extension cord(s) - Do not plug a device or devices into receptacles that exceed a total of 9.7A (1164 watts) - Do not open or attempt to open the unit for any reason WARNING: To reduce the risk of fire, electric shock or injury to persons: FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ISED RSS Warning/ISED RF Exposure Statement ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés. Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.

QA-FR-170-B LEADER ELECTRONICS CORP. ADD: No.8 Yuanshan Rd., Kunshan,Jiangsu, China TEL: 0512-57269888 FAX: 0512-57269899 E- mail: [email protected] FCC Authorization Date:2022/11/11 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , LEADER ELECTRONICS CORP, Hereby authorizes Shenzhen Accurate Technology Co.,Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co.,Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Si gnature: Printed Name: Johnny.lee Title: Product Manager

QA -FR-171-A LEADER ELECTRONICS CORP. ADD: No.8 Yuanshan Rd., Kunshan,Jiangsu, China TEL: 0512-57269888 FAX: 0512-57269899 E- mail: [email protected] FCC Confidential Authorization Date:2022/11/11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AR5U-DOCK1631 29W In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, LEADER ELECTRONICS CORP. hereby requests long-term confidential treatment of information accompanying this application as outlined below: •B lock Diagram •Schematics •Operation Description T he above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Johnny.lee Title: Product Manager

Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 1 of 3 External Photos Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 2 of 3 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 3 of 3

． • ， ， I

Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 1 of 20 Internal photos Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 2 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 3 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 4 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 5 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 6 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 7 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 8 of 20 Coil Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 9 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 10 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 11 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 12 of 20 Coil Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 13 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 14 of 20 Coil Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 15 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 16 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 17 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 18 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 19 of 20 Shenzhen Accurate Technology Co., Ltd. Project No.: KS2211222-66483E-RF Page 20 of 20

Shenzhen Accurate Technology Co., Ltd. Report No.: KS2211222-66483E-RF-00A Version 43: 2021-11-09 Page 10 of 27 FCC- WPT FCC §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According with KDB 680106 D01 RF Exposure Wireless Charging Apps v03r01 clause 3 c) According to KDB 680106 D01 RF Exposure Wireless Charging App v03r01 clause 5 b) Shenzhen Accurate Technology Co., Ltd. Report No.: KS2211222-66483E-RF-00A Version 43: 2021-11-09 Page 11 of 27 FCC- WPT Block Diagram of Test Setup Note: For mobile condition distance: A/B/C/D is 15cm; E is 20cm; Test Data Environmental Conditions Temperature: 26C Relative Humidity: 51 % ATM Pressure: 101.0 kPa The testing was performed by Nick Fang on 2022-10-30. Test Mode: Wireless Charging (Worst case for maximum power full load) Electric and Magnetic Field Analyzer B(Rear) EUT A(Front) C(Left) D(Right) E(Top) F(Bottom) Distance(Unit: cm) Shenzhen Accurate Technology Co., Ltd. Report No.: KS2211222-66483E-RF-00A Version 43: 2021-11-09 Page 12 of 27 FCC- WPT H-Field Strength Frequency Range (kHz) Position A (A/m) Position B (A/m) Position C (A/m) Position D (A/m) Position E (A/m) 50% Limit (A/m) Limit (A/m) 110 .5kHz-205kHz 0.222 0.104 0.111 0.114 0.106 0.815 1.63 E-Field Strength Frequency Range (kHz) Position A (V/m) Position B (V/m) Position C (V/m) Position D (V/m) Position E (V/m) 50% Limit (V/m) Limit (V/m) 110 .5kHz-205kHz 2.174 0.542 0.625 0.586 0.319 307 614 Note: Test with 15cm distance from the center of the probe(s) to the edge of the device, 20cm from the center of the probe(s) to the top of the device. Result: Pass Considerations of compliance 680106 D01 RF Exposure Wireless Charging App v03r01 clause 5 b: (1) Power transfer frequency is less than 1 MHz. Yes, the operation frequency is 110.5-205kHz. (2) Output power from each primary coil is less than or equal to 15 watts. Yes, the maximum output power of primary coil is 10 Watts. (3) The system may consist of more than one source primary coils, charging one or more clients. If more than one primary coil is present, the coil pairs may be powered on at the same time. The transfer system includes nine primary coils to detect. They divided into three sets, each set has three coils. Three sets can work at the same time, but each set of coils only one was worked at a time which has the same power and other performance declared by manufacturer*. (4) Client device is placed directly in contact with the transmitter. Yes, client device is placed directly in contact with the transmitter (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes, mobile exposure conditions only. (6) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the surface from all coils that by design can simultaneously transmit, and while those coils are simultaneously energized, are demonstrated to be less than 50% of the applicable MPE limit. Yes, the test result for H and E-Field strength less than 50% of the MPE limit.

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 43: 2021-11-09 Page 1 of 27 FCC- WPT TEST REPORT Applicant Name : LEADER ELECTRONICS CORP. Address : No.8 Yuanshan Rd., Kunshan,Jiangsu, China Report Number : KS2211222-66483E-RF-00A FCC ID: 2AR5U-DOCK163129W Test Standard (s) FCC Part 15C Sample Description Product Type: DOCK163129W Model No.: DOCK163129W Trade Mark: N/A Date Received: 2021-12-22 Report Date: 2022-10-31 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Ting Lü Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: KS2211222-66483E-RF-00A Version 43: 2021-11-09 Page 2 of 27 FCC- WPT TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 3 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 JUSTIFICATION ............................................................................................................................................................. 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 LOCAL SUPPORT EQUIPMENT ....................................................................................................................................... 5 EXTERNAL I/O CABLE.................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 11 TEST DATA ................................................................................................................................................................ 11 FCC§15.203 – ANTENNA REQUIREMENT ........................................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 ANTENNA CONNECTED CONSTRUCTION .................................................................................................................... 13 FCC §15.207 – AC LINE CONDUCTED EMISSION ............................................................................................. 14 APPLICABLE STANDARD ............................................................................................................................................ 14 EUT SETUP ................................................................................................................................................................ 14 EMI TEST RECEIVER SETUP ....................................................................................................................................... 14 TEST PROCEDURE ...................................................................................................................................................... 14 CORRECTED FACTOR & MARGIN CALCULATION ....................................................................................................... 15 TEST DATA .....................…

Text truncated - open the document above for the full version.