2ARJ5-AP05-D1Gateway

D1 Gateway User Manual Item Parameter Type ETAP05-D1 Structure size 190mm(H)×190mm(V)×41mm(D) Weight 360g Appearance color White Operating voltage DC 12V Operating current less than 300mA Work Mode 2.4GHz Work distance Open space distance ≥ 30 meters Data Interface Standard network cable interface Storage temperature -30°C~70°C Configure interface USB2.0 Humidity ≤80%RH Gateway Ceiling installation accessory Set screw Accessories in The Box Product Parameters Front side introduction Status indicator LED_ B: Power indicator LED_ R: Work indicator Base Station Introduction Back side introduction Item Parameter Power interface Use the standard DC 12V power supply Power indication Two lights are always on, indicating that the power supply of the base station is normal Data interface Use UTP/STP of category 5 or above Configure interface USB2.0, USB flash disk configuration Reset button Press the reset button for about 8 seconds until the yellow light stays on and then goes off, indicating reset completion. A c c e s s o r y interface Use with ceiling mounting accessories Base Station Introduction Hardware Environment Setup 1.1 Connect the base station to the power supply and wait for about 20 seconds until the red light comes on, indicating that it is ready to operate. 1.2 Plug an Ethernet cable into the base station to connect it to the computer. 1.3 In the computer's network connections, change the Ethernet IP address to 192.168.172.172 and the subnet mask to 255.255.255.0. After the modification is complete, power cycle the base station. Installation and configuration steps 1 Open the eStation_PTL_Demo configuration tool and set the relevant parameters. 2.1 Click "RUN". If data appears in the lower left corner, it means the base station is successfully connected to the Demo tool. If no data appears, press and hold the reset button on the base station to reset it. (Remember to power cycle the base station.) 2.2 Control the light strip to turn on. Right-click in the gray area on the left, click "Edit list" to add the light strip. 2.3 In the "Edit Light Strip List", enter a light strip number in each row (ensure the input method is in English). You can add multiple light strips. Finally, click "Save" to complete the addition of the light strips. 2 2.4 Select the light strip you want to control and choose its parameters: "R" for red, "G" for green, "B" for blue, and you can also mix and match these colors; "Beep" for the buzzer to sound; "Blink" for the light to flash. "Time" represents the duration in seconds. Finally, click "Send". The corresponding light strip will respond accordingly. 2.5 Configure the base station for public network deployment or local deployment. Using Seekron public network deployment as an example, click "CONF". In "AP Config", set the base station parameters: "Server Address" is the IP address of the server the base station communicates with; "Port" is the server's open port number; "Account, Password" are the server's access credentials; "IP Address" is the base station's IP (customizable but must be in the same network segment as the server IP); " Subnet Mask" and "Gateway Address" are customizable. Finally, click "Settings". nstallation and setup steps Power cycle the device and connect to use it. 3.1 After configuration is complete, disconnect the Ethernet cable from the computer, connect it to the public network, and power cycle the base station. 3.2 Open the server website to check if the base station is online. If the "Status" shows a red heart, it means the base station has successfully gone online. Installation and setup steps 3 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches)during normal operation. That changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: CLF Import and Export Limited Contact Name: David Chen FRN: 0033489683 Address: 1312 17th Street #692,Denver,CO 80202,Unite States Telephone No: (949)254-2565 Email: [email protected] EIN: 98-1720547 Applicant: Company name: Suzhou Etag-Technology Corporation Product Description: Gateway Grantee code: 2ARJ5 FCC ID: 2ARJ5-AP05-D1 FRN: 0033942970 Contact Name: Haiyan Zhang Address: Room 236, 2/F Ming De Building, No.166 Ren ai Road, Suzhou Industrial Park, Suzhou, China Telephone No: 0512-62796964 Fax No: 0512-62796964 Email: [email protected] [Suzhou Etag-Technology Corporation] certifies that, as of the date of this filing of the application with the TCB, [CLF Import and Export Limited]is our designated US agent for service of process for the above referenced FCC ID. [Suzhou Etag- Technology Corporation] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [CLF Import and Export Limited]accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2026/08/10 Applicant’s Name: Haiyan Zhang US Agent’s Name: David Chen Title: Manager Title: Manager Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Suzhou Etag-Technology Corporation Grantee code: 2ARJ5 FCC ID: 2ARJ5-AP05-D1 FRN: 0033942970 Contact Name: Haiyan Zhang Address: Room 236, 2/F Ming De Building, No.166 Ren ai Road, Suzhou Industrial Park, Suzhou, China Telephone No: 0512-62796964 Fax No: 0512-62796964 Email: [email protected] i. [Suzhou Etag-Technology Corporation] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Suzhou Etag-Technology Corporation] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Suzhou Etag-Technology Corporation] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2026/08/10 Applicant’s Name: Haiyan Zhang Title: Manager Signature The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

Suzhou Etag-Technology Corporation Code 00018768 Ed. 1 Item 1. The device is able to install software/program installation? ☐ Yes, go to Item 2. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Device Gateway Company name Suzhou Etag-Technology Corporation Grantee code 2ARJ5 FCC ID 2ARJ5-AP05-D1 FRN 0033942970 Contact name Haiyan Zhang Address Room 236, 2/F Ming De Building, No.166 Ren ai Road, Suzhou Industrial Park, Suzhou, China Telephone number 0512-62796964 E-mail [email protected] Chipset/module information PHY6222 Operating System (if applicable) / Storage Capacity (hard drive or other permanent memory storage, if applicable) / 2 Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 3 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher 3 RAM: 1 GB 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; 4 After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐ Yes, go to Item 3. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3. Connectivity Capabilities: # Physical Interface Purpose Justification 1 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒ Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Haiyan Zhang Date: 2026.08.10 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications.

TCBCALLpágina1 FileFCCID:2ARJ5-AP05-D1 PleaseuploadanexhibitthatexplainshowdoestheTCBverifythenewagentinformation: 1-IstheaddressoftheagentavalidphysicalUSmailingaddress(notaUSpostofficebox,notavirtualmailbox,notP.O.Boxes,notavacantlot,notapublicbuilding, etc.) ○Wehavecheckediftheaddressexistsinarealandpotentialbuilding(Googlemaps)+officialUSregister,afterthisverificationandtheevidencebelowwecan guaranteethefollowing: notaUSpostofficebox notavirtualmailbox notP.O.Boxes notavacantlot notapublicbuilding(note) ►WecheckedtheFCCFRNSearchbasedontheinformationprovidedbythegrantee. Ontheofficialregisterfrom:https://opencorporates.com/companies/us_co/20231240414 Ingoogle: TCBCALLpágina2 ►CONCLUSIONbyTCB:TheASOPdefinedandprovidedbygranteeisVALIDandconfirmed.Thereforetheexhibit"2BOVE-HK-712USAgentforServiceofProcess LETTEROFATTESTATION"includedinthefileisok. 2-IstheagentphysicallylocatedatthatvalidUSaddresssuchthattheagentcanbelegallyservedatthataddress? Yes,checkabove 3-Hasthelistedagentclearlyagreedinwritingtoserveastheagentforthegranteeatthataddress? Yes,itisincludedintheexhibit"2BOVE-HK-712USAgentforServiceofProcessLETTEROFATTESTATION" >

C5266091_X10_Ed.2 1/1 Suzhou Etag-Technology Corporation Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2026-08-10 Subject: Request for Confidentiality FCC ID: 2ARJ5-AP05-D1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Haiyan Zhang Title: Manager

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Suzhou Etag-Technology Corporation Address: Room 236, 2/F Ming De Building, No.166 Ren ai Road, Suzhou Industrial Park, Suzhou, China Product Name: Gateway Model Number: ETAP05-D1 FCC Identifier: 2ARJ5-AP05-D1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Haiyan Zhang 2026-08-10 Title: Manager Signature of applicant:

Shenzhen QC Testing Laboratory Co., Ltd. Page 1 of4 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Product Name: G a t e w a y Test Model No.: ETAP05-D1 EUT Constructional Details Shenzhen QC Testing Laboratory Co., Ltd. Page 2 of4 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Shenzhen QC Testing Laboratory Co., Ltd. Page 3 of4 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Shenzhen QC Testing Laboratory Co., Ltd. Page 4 of4 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn ------End------

Shenzhen QC Testing Laboratory Co., Ltd. Page 1 of5 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Product Name: G a t e w a y Test Model No.: ETAP05-D1 EUT Constructional Details： Antenna 2 Module 2 Module 1 Antenna 1 Module 3 Antenna 3 Shenzhen QC Testing Laboratory Co., Ltd. Page 2 of5 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Shenzhen QC Testing Laboratory Co., Ltd. Page 3 of5 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Shenzhen QC Testing Laboratory Co., Ltd. Page 4 of5 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Shenzhen QC Testing Laboratory Co., Ltd. Page 5 of5 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn -----End------

Shenzhen QC Testing Laboratory Co., Ltd. Page 1 of 2 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn FCC ID: 2ARJ5-AP05-D1 RF Exposure Evaluation FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, and highest channel individually. Shenzhen QC Testing Laboratory Co., Ltd. Page 2 of 2 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Test Result of RF Exposure Evaluation For worst case Antenna Gain: 5.97dBi Test Frequency （MHz） Minimum Separation Distance (cm) Output Power (dBm) Target power (dBm) Target power (mW) Antenna Gain (Numeric) Power Density Limit (mW/cm 2 ) Power Density At 20 cm (mW/cm 2 ) Test Results 2402 20 -0.15 0±1 1.26 3.95 1 0.001 Pass Simultaneous Transmission for SAR Exclusion These same three modules and antennas can all operate simultaneously., need consider simultaneous transmission. Maximum SAR Ratio Ant1 Maximum SAR Ratio Ant2 Maximum SAR Ratio Ant3 ∑SAR ratio Ant1 + SAR ratio Ant2 + SAR ratio Ant3 Limit Results 0.001 0.001 0.001 0.003 1 PASS Remark: 1. Output power including tune-up tolerance; 2.Max. SAR Ratio=Max. Evaluation Values/Sar Limit. The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure.

Shenzhen QC Testing Laboratory Co., Ltd. Report No.: QCT26GR-1827E-01 Page 1 of 42 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn FCC PART 15.247 TEST REPORT On Behalf of Suzhou Etag-Technology Corporation Room 236, 2/F Ming De Building, No.166 Ren ai Road, Suzhou Industrial Park, Suzhou, China FCC ID: 2ARJ5-AP05-D1 Model: ETAP05-D1 August 5, 2026 T hi s Repor t Concer ns: Or iginal Report Equi pm ent T ype: G at eway Test Engineer: Fan Yang / Report Number: QCT26GR-1827E-01 Test Date: July 24-28, 2026 Test Result: Pass Reviewed By: Vincent Yang / Approved By: Kendy Wang / Prepared By: Shenzhen QC Testing Laboratory Co., Ltd. East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 Shenzhen QC Testing Laboratory Co., Ltd. Report No.: QCT26GR-1827E-01 Page 2 of 42 Address: East of 1/F., Building E, Xinghong Science Park, No.111, Shuiku Road, Fenghuanggang, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China Tel: 0755-23008269 Fax: 0755-23726780 http://www.qctest.com.cn Table of Contents 1. GENERAL INFORMATION ................................................................................................. 5 1.1 Product Description for Equipment under Test (EUT) ............................................................. 5 1.2 System Test Configuration ...................................................................................................... 6 1.3 Test Facility.............................................................................................................................. 7 1.4 Measurement Uncertainty ........................................................................................................ 7 2. SUMMARY OF TEST RESULTS ........................................................................................ 8 3. LIST OF TEST AND MEASUREMENT INSTRUMENTS .................................................... 9 3.1 Conducted Emission Test ........................................................................................................ 9 3.2 Radiated Emission Test ........................................................................................................... 9 3.3 RF Conducted test ................................................................................................................. 10 4. ANTENNA REQUIREMENT .............................................................................................. 11 5. CONDUCTED EMISSIONS ............................................................................................... 12 5.1 Applicable Standard............................................................................................................... 12 5.2 Limit ....................................................................................................................................... 12 5.3 Test setup .............................................................................................................................. 12 5.4 EMI Test Receiver Setup ....................................................................................................... 12 5.5 Test procedure....................................................................................................................... 12 5.6 Test Data ............................................................................................................................... 12 6. CONDUCTED PEAK OUTPUT POWER ........................................................................... 15 6.1 Applicable Standard............................................................................................................... 15 6.2 Limit ....................................................................................................................................... 15 6.3 Test setup .............................................................................................................................. 15 6.4 Test Procedure ...................................................................................................................... 16 6.5 Test Data ............................................................................................................................... 16 7. CHANNEL BANDWIDTH & 99% OCCUPIED BANDWIDTH ........................................... 19 7.1 Applicable Standard............................................................................................................... 19 7.2 Limit ....................................................................................................................................... 19 7.3 Test setup .............................................................................................................................. 19 7.4 Test Procedure ...................................................................................................................... 19 7.5 Test Data ............................................................................................................................... 20 8. POWER SPECTRAL DENSITY ........................................................................................ 25 8.1 Applicable Standard............................................................................................................... 25 8.2 Limit ....................................................................................................................................... 25 8.3 Test setup .............................................................................................................................. 25 8.4 Test Procedure .........................................................................................................…

Text truncated - open the document above for the full version.

Product Number: 2.4G Antenna L=120mm MHF Product Name ：008.ETS001062 Page 1 Version: 1.0 Issue Date: 2024-5-6 Manufacturer: Kunshan Fengxun Electronics Co., Ltd. 2nd Floor, Factory 4, No. 811 Huayuan Road, Zhangpu Town, Kunshan, Jiangsu Province, China Index: 1. Reliability Testing 2. Specification 3. S Parameter Test Data 4. Antenna Radiation Pattern Product Number: 2.4G Antenna L=120mm MHF Product Name ：008.ETS001062 Page 2 Version: 1.0 Issue Date: 2024-5-6 Product Number: 2.4G Antenna L=120mm MHF Product Name ：008.ETS001062 Page 3 Version: 1.0 Issue Date: 2024-5-6 Test Item Procedure Requirement 1. Reliability Testing 1. Visual inspection Applicable methods follow specification and Dimension Check using x5 magnification 2. Rapid Changing -40 ̊C (30minutes) to After 2 hours recovery: of Temperature 90 ̊C (30minutes); 24 cycles 1. no visible damage 2. Freq. Tol.: < ±5% 3. Damp Heat 24 hours at 60 ̊C; 90 ~ 95% RH After 2 hours recovery: 1. no visible damage 2. Freq. Tol. : < ±5% 4. …

Text truncated - open the document above for the full version.