2ARTO-RPI703M26000CSub 1G & BLE module

MyDeltaSolar DC1 and User Interface AskaChiu 2018.09.13 Delta Confidentia Model Name : RPI703M260000-C 2 Additional notes: (15.21) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. (Not including low power device (below 20mW)) 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ◆Reorient or relocate the receiving antenna. ◆Increase the separation between the equipment and receiver. ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. ◆Consult the dealer or an experienced radio/TV technician for help. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in th e upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements require with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain lapt configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: "Contains TX FCC ID: 2ARTO-RPI703M26000C Un-license band: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device maynot cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesiredoperation. Delta Confidential 低功率射頻電機設備警語 Model Name : RPI703M260000-C| 3 依據低功率電波輻射性電機管理辦法 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾 現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之 無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Delta Confidential 1. This APP should collocate with data collector and Delta Inverter. 2. If inverter is not connected to cloud, you still can monitor inverter operation by APP. MyDeltaSolar QR CodeIOS https://itunes.apple.com/ng/app/myd eltasolar/id1271609228?mt=8 Android https://play.google.com/store/apps/de tails?id=com.mydeltasolar_1_0_0.app &hl=zh-TW Where can search for MyDeltaSolar APP? -QR Code: Please scan the QR code to DSC cloud (web). -IOS system: Please search “MyDeltaSolar” in App store. -Android system: Please search “MyDeltaSolar” in Google Play. Download APP Download MyDeltaSolar APP| 4 Delta Confidential Forget password Create account Language 5 Login [email protected] 8-16 characters -Login : 1. Please fill in user e-mail & password. *If you have registered, the mobile will remember account info. Then please fill in password. 2. Please click “Create account” to create an user‘s account. 3. User have to check the box to enable "Go to Register" button. 4. Please click “Go to Register” to register. I had read and agree this declaration as above. Go to Register V1.15 Sign In x Go to Register V1.19 [email protected] 1 2 3 You must need a MyDeltaSolar account in order to use our cloud services. Delta may collect your personal data and protect your privacy when you use MyDeltaSolar service. By using MyDletaSolar service, you agree that Delta can use such data and monitor your inverter’s status if necessary. In some case, Delta employees, authorized contractors or agents may need to use your account to analyze any issue and problem you have while using Delta solar inverter or service. We restrict access to personal information to Delta employees, contractors and agents who need to know that information in order to process it for us, and who are subject to strict contractual confidentiality obligations and may be disciplined or terminated if they fail to meet these obligations. Use MyDeltaSolar Service terms and conditions : User & Plant Reg…

Text truncated - open the document above for the full version.

External photo of EUT External photo of EUT I-Pex External photo of EUT Antenna 1 Antenna 1 External photo of EUT Antenna 1 Antenna 2 External photo of EUT Antenna 2 Antenna 2

Internal photo of EUT Lora module Internal photo of EUT BLE module

Delta Electronics, Inc. TEST REPORT SCOPE OF WORK: FCC 1.1310 – Maximum Permissible Exposure report Model: RPI703M260000-C REPORT NUMBER 211000362THC-001 ISSUE DATE Feb. 08, 2022 PAGES 14 DOCUMENT CONTROL NUMBER GFT-OP-10h (28-Nov-2018) © 2020 Intertek Report No.: 211000362THC-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. GFT-OP-10h (28-Nov-2018) Page 1 of 14 Test Report Maximum Permissible Exposure (MPE) Evaluation Report Applicant: Delta Electronics, Inc. No.39, Sec. 2, Huandong Rd., Shanhua Dist., Tainan City 741, Taiwan Product: Sub 1G & BLE module Model No.: RPI703M260000-C FCC ID: 2ARTO-RPI703M26000C Test Method/ Standard: 47 CFR FCC 1.1310 KDB 447498 Test By: Intertek Testing Services Taiwan Ltd., Hsinchu Laboratory No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan Zero Chen Engineer Rico Deng Reviewer Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 2 of 14 TEST REPORT Revision History Report No. Issue Date Revision Summary 211000362THC-001 Feb. 08, 2022 Original report Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 3 of 14 TEST REPORT Table of Contents 1. General Information ............................................................................................................... 5 1.1 Identification of the EUT .................................................................................................. 5 1.2 Antenna description ......................................................................................................... 5 1.3 Peripherals equipment ..................................................................................................... 6 2. Test specifications ................................................................................................................... 7 2.1 Introduction ...................................................................................................................... 7 2.2 RF Exposure Limit ............................................................................................................. 8 2.3 RF Exposure calculations ................................................................................................ 11 2.4 Operation mode ............................................................................................................. 11 2.5 Test equipment ............................................................................................................... 12 2.6 Test Set-up ...................................................................................................................... 12 3. Test results ............................................................................................................................ 13 Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 4 of 14 TEST REPORT Summary of Tests MPE Evaluation meet FCC OET No. 65: 1997, IEEE C95.1-2005 Test Reference Results MPE Evaluation FCC Guidelines for Human Exposure IEEE C95.1 Complies Note: Please note that the test results with statement of conformity, the decision rules which are based on: Safety Testing: the specification, standard or IEC Guide 115. Other Testing: the specification, standard and not taking into account the measurement uncertainty. Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 5 of 14 TEST REPORT 1. General Information 1.1 Identification of the EUT Product: Sub 1G & BLE module Model No.: RPI703M260000-C Operating Frequency: 1. 2402 MHz ~ 2480 MHz for BLE 2. 903 MHz ~ 927 MHz for Lora Channel Number: 1. 40 channels for BLE 2. 33 channels for Lora Rated Power: DC 12V Power Cord: N/A Sample receiving date: 2021/08/30 Sample condition: Workable Test Date(s): 1. 2021/08/31, 2. 2022/01/19 1.2 Antenna description For BLE Antenna Type : Chip antenna Connector Type : Fixed Antenna Gain : 0 dBi For Lora Antenna 1 Antenna Type : Dipole antenna Connector Type : SMA Antenna Gain : 2.26 dBi Antenna 2 Antenna Type : Dipole antenna Connector Type : SMA Antenna Gain : 1.73 dBi Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 6 of 14 TEST REPORT 1.3 Peripherals equipment For BLE Peripherals Brand Model No. Serial No. Description of Data Cable Notebook PC HP HP Probook 440 G3 5CD8021S9H Mini USB 1m × 1 Adapter DELTA MDS-030AAC12 N/A N/A Fixture N/A N/A N/A N/A For Lora Peripherals Brand Model No. Serial No. Data cable Notebook PC HP HP Probook 440 G3 5CD8021S9H N/A USB Converter TRP TRP-C08 N/A USB shielded cable 2m DC Power Supply Twintex TP-1603C N/A N/A Report No.: 211000362THC-001 GFT-OP-10h (28-Nov-2018) Page 7 of 14 TEST REPORT 2. Test specifications 2.1 Introduction The EUT operates in the 2.4 GHz band. Due to the EUT (include antenna) at its normal operation distance is at least 20 cm from the human body, the EUT was defined as a Mobile Device. The reason to do the MPE Evaluation is to avoid the RF hazard to human body. The maximum output power and gain of the antenna were used to calculate the limited Power density (S) at 20 cm distance away from the product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 and Sa…

Text truncated - open the document above for the full version.

Delta Electronics, Inc. TEST REPORT SCOPE OF WORK: 47 CFR FCC Part 15.247 – Radio Spectrum report Model: RPI703M260000-C REPORT NUMBER 211000342THC-001 ISSUE DATE Feb. 08, 2021 PAGES 40 DOCUMENT CONTROL NUMBER GFT-OP-10h (28-Nov-2018) © 2020 Intertek Report No.: 211000342THC-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. GFT-OP-10h (28-Nov-2018) Page 1 of 40 Test Report 0597 Radio Spectrum TEST REPORT Applicant: Delta Electronics, Inc. No.39, Sec. 2, Huandong Rd., Shanhua Dist., Tainan City 741, Taiwan Product: Sub 1G & BLE module Model No.: RPI703M260000-C FCC ID: 2ARTO-RPI703M26000C Test Method/ Standard: 47 CFR FCC Part 15.247 & ANSI C63.10 2013 KDB 558074 D01 v05r02 Test By: Intertek Testing Services Taiwan Ltd., Hsinchu Laboratory No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan Zero Chen Engineer Rico Deng Reviewer Report No.: 211000342THC-001 GFT-OP-10h (28-Nov-2018) Page 2 of 40 TEST REPORT Revision History Report No. Issue Date Revision Summary 211000342THC-001 Feb. 08, 2022 After engineer judgment and comparing the version the radiation 9kHz-30MHz test considered necessary. Then the other test data in this report are based on Report No.: 210800524THC-001. Report No.: 211000342THC-001 GFT-OP-10h (28-Nov-2018) Page 3 of 40 TEST REPORT Table of Contents Summary of Test Data ................................................................................................................ 5 1. General Information ............................................................................................................... 6 1.1 Identification of the EUT .................................................................................................. 6 1.2 Antenna description ......................................................................................................... 6 1.3 Operation mode ............................................................................................................... 6 1.4 Peripherals equipment ..................................................................................................... 7 2. Minimum 6 dB Bandwidth ..................................................................................................... 8 2.1 Instrument Setting ............................................................................................................ 8 2.2 Test Procedure .................................................................................................................. 8 2.3 Test Diagram ..................................................................................................................... 8 2.4 Limit .................................................................................................................................. 8 2.5 Test Results ....................................................................................................................... 9 3. Maximum Peak Conducted Output Power ........................................................................... 12 3.1 Instrument Setting .......................................................................................................... 12 3.2Test Procedure ................................................................................................................. 12 3.3 Test Diagram ................................................................................................................... 12 3.4 Limit ................................................................................................................................ 12 3.5 Test Results ..................................................................................................................... 13 4. Power Spectral Density ......................................................................................................... 14 4.1 Instrument Setting .......................................................................................................... 14 4.2 Test Procedure ................................................................................................................ 14 4.3 Test Diagram ................................................................................................................... 14 4.4 Limit ................................................................................................................................ 14 4.5 Test Results ..................................................................................................................... 15 5. Emissions in Non-Restricted Frequency Bands .................................................................... 18 5.1 Instruments Setting ........................................................................................................ 18 5.2 Test Procedure ................................................................................................................ 18 5.3 Test Diagram ................................................................................................................... 18 5.4 Limit .......................................…

Text truncated - open the document above for the full version.

Delta Electronics, Inc. TEST REPORT SCOPE OF WORK: 47 CFR FCC Part 15.247 – Radio Spectrum report Model: RPI703M260000-C REPORT NUMBER 211100338THC-001 ISSUE DATE Feb. 08, 2022 PAGES 29 DOCUMENT CONTROL NUMBER GFT-OP-10h (28-Nov-2018) © 2020 Intertek Report No.: 211100338THC-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. GFT-OP-10h (28-Nov-2018) Page 1 of 29 Test Report 0597 Radio Spectrum TEST REPORT Applicant: Delta Electronics, Inc. No.39, Sec. 2, Huandong Rd., Shanhua Dist., Tainan City 741, Taiwan Product: Sub 1G & BLE module Model No.: RPI703M260000-C FCC ID: 2ARTO-RPI703M26000C Test Method/ Standard: 47 CFR FCC Part 15.247 & ANSI C63.10 2013 KDB 558074 D01 v05r02 Test By: Intertek Testing Services Taiwan Ltd., Hsinchu Laboratory No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan Zero Chen Engineer Rico Deng Reviewer Report No.: 211100338THC-001 GFT-OP-10h (28-Nov-2018) Page 2 of 29 TEST REPORT Revision History Report No. Issue Date Revision Summary 211100338THC-001 Feb. 08, 2022 Original report Report No.: 211100338THC-001 GFT-OP-10h (28-Nov-2018) Page 3 of 29 TEST REPORT Table of Contents 1. General Information ............................................................................................................... 5 1.1 Identification of the EUT .................................................................................................. 5 1.2 Antenna description ......................................................................................................... 5 1.3 Operation mode ............................................................................................................... 6 1.4 Peripherals equipment ..................................................................................................... 6 2. Minimum 6 dB Bandwidth ..................................................................................................... 7 2.1 Instrument Setting ............................................................................................................ 7 2.2 Test Procedure .................................................................................................................. 7 2.3 Test Diagram ..................................................................................................................... 7 2.4 Limit .................................................................................................................................. 7 2.5 Test Results ....................................................................................................................... 8 3. Maximum Peak Conducted Output Power ........................................................................... 10 3.1 Instrument Setting .......................................................................................................... 10 3.2Test Procedure ................................................................................................................. 10 3.3 Test Diagram ................................................................................................................... 10 3.4 Limit ................................................................................................................................ 10 3.5 Test Results ..................................................................................................................... 11 4. Power Spectral Density ......................................................................................................... 12 4.1 Instrument Setting .......................................................................................................... 12 4.2 Test Procedure ................................................................................................................ 12 4.3 Test Diagram ................................................................................................................... 12 4.4 Limit ................................................................................................................................ 12 4.5 Test Results ..................................................................................................................... 13 5. Emissions in Non-Restricted Frequency Bands .................................................................... 15 5.1 Instruments Setting ........................................................................................................ 15 5.2 Test Procedure ................................................................................................................ 15 5.3 Test Diagram ................................................................................................................... 15 5.4 Limit ................................................................................................................................ 15 5.5 Test Results ..................................................................................................................... 15 6. Emissions in Restricted Frequency Bands (Radiated emission measurements…

Text truncated - open the document above for the full version.

Radiated Emission Test set-up photo 9kHz~30MHz Radiated Emission Test set-up photo 30MHz~1GHz Radiated Emission Test set-up photo Above 1GHz