2AS7P-SIPEED-M1AMaix-I Audio Module

     Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTES Co-location warning: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. OEM integration instructions: This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s) that has been originally tested and certified with this module. As long as the conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Validity of using the module certification: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re- evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End product labeling: The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2AS7P-SIPEED-M1A”. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all r equired regulatory information/warning as show in this manual. Integration instructions for host product manufactures according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15 Subpart C 15.247 2.3 Specific operational use conditions The module is a module with 2.4G wifi function. WiFi Specification： Operation Frequency: 2412~2462MHz Number of Channel: 11 Modulation: DSSS, OFDM Type: PCB Antenna Gain: 0.43dBi The module can be used for mobile or applications with a maximum 0.43dBi antenna. The host manufacturer installing this module into their product must ensure that the final composit product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operaition. The host manufacturer has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2.4 Limited module procedures Not applicable. The module is a single module and complies with the requirement of FCC Part 15.212/ RSP-100. 2.5 Trace antenna designs Not applicable. The module has its own antenna, and doesn’t need a host’s printed board microstrip trace antenna etc. 2.6 RF exposure considerations The module must be installed in the host equipment such that at least 20cm is maintained between the antenna and users ’ body; and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module c annot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization 2.7 Antennas Antenna Specification are as follows: Type: PCB Antenna Gain: 0.43dBi This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the internal antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a ‘unique’ antenna coupler. As long as the conditions above are met, f…

Text truncated - open the document above for the full version.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Company S. Union Consult Inc Contact Name: FEIMING LIU Address: 2020S Hacienda Blvd, STE M, Hacienda Heights, California 91745, USA Telephone No: +1 (626)476-3164 Email: [email protected] Applicant: Company name: Shenzhen Sipeed Technology Co, Ltd. FRN: 0028444578 Product Description: Maix-I Audio Module Grantee code: 2AS7P FCC ID: 2AS7P-SIPEED-M1A Contact Name: Caesar Wu Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Telephone No: +86 13798563227 Email: [email protected] [Shenzhen Sipeed Technology Co, Ltd.] certifies that, as of the date of this filing of the application with the TCB, [Company S. Union Consult Inc] is our designated US agent for service of process for the above referenced FCC ID. [Shenzhen Sipeed Technology Co, Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Company S. Union Consult Inc] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 5.08.2023 Applicant’s Name: Caesar Wu US Agent’s Name: FEIMING LIU Title: RD Director Title: staff member Signature Signature

C5266091_X24_Ed.1 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Shenzhen Sipeed Technology Co, Ltd Grantee code: 2AS7P FCC ID: 2AS7P-SIPEED-M1A Contact Name: Caesar Wu Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Telephone No: +86 13798563227 Fax No: +86 755-27808509 Email: [email protected] i. [Shenzhen Sipeed Technology Co, Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Sipeed Technology Co, Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. Date: 5.0 8.2023 Applicant’s Name: Caesar Wu Title: RD Director Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Sipeed Technology Co, Ltd Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Product Name: Maix-I Audio Module Model Number: M1A FCC Identifier: 2AS7P-SIPEED-M1A We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Caesar Wu Date: 5/8/2023 Title: RD Director Signature of applicant:

C5266091_X10_Ed.1 1/1 Shenzhen Sipeed Technology Co, Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 5/8/2023 Subject: Request for Confidentiality FCC ID: 2AS7P-SIPEED-M1A To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Caesar Wu Date: 5/8/2023 Title: RD Director

C5266091_X9_Ed.2 1/1 Shenzhen Sipeed Technology Co, Ltd Modular Transmitter Approval Request Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Company name: Shenzhen Sipeed Technology Co, Ltd FCC ID: 2AS7P-SIPEED-M1A Gentlemen, In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module Certification Guide V02’. FCC ID: 2AS7P-SIPEED-M1A has been examined against the following requirements. Items to be covered by Single modular transmitters. Requirement per 15.212 and KDB 996369 D01 ‘Modular Certification Guide v02 Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly Yes, The module has its own RF shield 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal Yes, The module has data transmission function and supports 2.4Gwifi function. 3. The module must contain power supply regulation on the module Module with power regulation and support for DC 5V/200mA input 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The module meets the antenna requirements. 5. The module must demonstrate compliance in a stand- alone configuration The module has been tested in a standalone configuration, see report for details 6. The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) The module has its own FCC ID number. See the label for details. 7. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee The module meets any specific rules or operational requirements applicable to the transmitter 8. The module must comply with RF exposure requirements Answer: The module complies with any applicable RF exposure requirements, as detailed in the instructions. Name: Caesar Wu Date: 2023-5-8 Title: RD Director Signature of applicant

Page 1 of 3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Appendix - EUT Photos Model: M1A Photo 1 Photo 2 Page 2 of 3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 Page 3 of 3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 ----End of Report----

Thelabelis locatedontheproductshield Thepositionof shieldingcoverhasbeenreserved.Pleaseseethefigurebelow

Page 1 of 1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Appendix - EUT Photos Model: M1A Photo 1 ----End of Report---- ANT

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] RF EXPOSURE Test Report Report No.: MTi221028005-07E2 Date of issue: 2023-03-30 Applicant: Shenzhen Sipeed Technology Co, Ltd. Product: Maix-I Audio Module Model(s): M1A FCC ID: 2AS7P-SIPEED-M1A Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 5 - Report No.: MTi221028005-07E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 5 - Report No.: MTi221028005-07E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Test Result Certification Applicant: Shenzhen Sipeed Technology Co, Ltd. Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Manufacturer: Shenzhen Sipeed Technology Co, Ltd. Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Product description Product name: Maix-I Audio Module Trademark: Sipeed Model name: M1A Serial Model: N/A Standards: N/A Test procedure: KDB 447498 D01 v06 Date of Test Date of test: 2023-01-03 ~ 2023-01-12 Test result: Pass Test Engineer : (Yanice Xie) Reviewed By: : (Leon Chen) Approved By: : (Tom Xue) - Page 4 of 5 - Report No.: MTi221028005-07E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) MPE Calculation Method Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1415926 R= distance between observation point and center of the radiator in cm(20cm) Pd the limit of MPE, 1mW/cm 2 . If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. - Page 5 of 5 - Report No.: MTi221028005-07E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Measurement Result 2.4GWiFi: Operation Frequency: WIFI 802.11b/g/n HT20: 2412-2462MHz, Power density limited: 1mW/ cm 2 Antenna Type: PCB Antenna; WIFI antenna gain: 0.43dBi R=20cm mW=10^(dBm/10) antenna gain Numeric=10^(dBi/10)= 10^(0.43/10)=1.10 2.4GWiFi: Channel Freq. (MHz) modulation conducted power Tune- up power Max Antenna Evaluation result at 20cm Power density Limits (dBm) (dBm) tune-up power Gain Power density(mW/cm 2 ) (mW/cm 2 ) (dBm) (mW) Numeric 2412 802.11b 20.6 20±1 21 125.893 1.1 0.02755 1 2437 20.33 20±1 21 125.893 1.1 0.02755 1 2462 20.06 20±1 21 125.893 1.1 0.02755 1 2412 802.11g 18.87 18±1 19 79.433 1.1 0.01745 1 2437 18.6 18±1 19 79.433 1.1 0.01745 1 2462 18.56 18±1 19 79.433 1.1 0.01745 1 2412 802.11n H20 18.13 18±1 19 79.433 1.1 0.01745 1 2437 17.86 18±1 19 79.433 1.1 0.01745 1 2462 17.76 18±1 19 79.433 1.1 0.01745 1 Conclusion: For the max result: 0.02755≤ 1.0 SAR, No SAR is required. ----END OF REPORT----

Passiveantennatestdatareport 1、Antennasizeandtestenvironmentdiagram testingenvironment 2、Antennastandingwaveratio 3、Passivetestdata Gain&Efficiency 增益、效率 frequency 频率 (MHz) gain 增益 (dBi) mingain 最小增 益(dBi) efficiency 效率(dB) efficiency 效率(%) 24000.09-8.69-3.5544.11 24100.18-8.48-3.4944.81 24200.21-9.22-3.4445.32 24300.3-8.16-3.3646.08 24400.36-9.12-3.3446.34 24500.35-8.17-3.3446.39 24600.43-9.05-3.346.8 24700.43-8.58-3.3546.19 24800.33-8.43-3.4245.49 24900.32-8.93-3.4545.21 25000.07-8.97-3.5244.45 4、polarGraphs 5、EtotalGraphs 6、3DGraphs ShenzhenAllThingsConnectedCommunicationCo.,Ltd November28,2022

Address: 101, No.7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi221028005-07E1 Date of issue: 2023-03-30 Applicant: Shenzhen Sipeed Technology Co, Ltd. Product: Maix-I Audio Module Model(s): M1A FCC ID: 2AS7P-SIPEED-M1A Shenzhen Microtest Co., Ltd. http://www.mtitest.com Page 2 of 54 Report No.: MTi221028005-07E1 Address: 101, No.7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. This test report shall not be partially reproduced without the written consent of the laboratory. 2. The test results in this test report are only responsible for the samples submitted 3. This test report is invalid without the seal and signature of the laboratory. 4. This test report is invalid if transferred, altered, or tampered with in any form without authorization. 5. Any objection to this test report shall be submitted to the laboratory within 15 days from the date of receipt of the report. Page 3 of 54 Report No.: MTi221028005-07E1 Address: 101, No.7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Table of contents 1 General Description ........................................................................................................................ 5 1.1 Description of the EUT .................................................................................................................................. 5 1.2 Description of test modes ............................................................................................................................. 6 1.3 Environmental conditions for testing ............................................................................................................. 7 1.4 Description of support units .......................................................................................................................... 7 2 Measurement uncertainty ............................................................................................................... 8 3 Summary of Test Result ................................................................................................................. 9 4 Test Laboratory ............................................................................................................................. 10 5 Equipment List .............................................................................................................................. 11 6 Test Result ..................................................................................................................................... 12 6.1 Antenna requirement .................................................................................................................................. 12 6.2 AC power line conducted emissions ........................................................................................................... 13 6.3 Radiated spurious emission ........................................................................................................................ 16 6.4 DTS bandwidth ........................................................................................................................................... 25 6.5 Maximum conducted output power ............................................................................................................. 26 6.6 Power spectral density ................................................................................................................................ 27 6.7 Band edge (Conducted) .............................................................................................................................. 28 6.8 Conducted spurious emissions ................................................................................................................... 29 6.9 Duty Cycle ................................................................................................................................................... 30 Appendix A: DTS Bandwidth ............................................................................................................... 31 Appendix B: Maximum conducted output power ............................................................................... 35 Appendix C: Maximum power spectral density .................................................................................. 36 Appendix D: Band edge measurements ............................................................................................. 40 Appendix E: Conducted Spurious Emission ...................................................................................... 42 Appendix F: Duty Cycle ....................................................................................................................... 51 Photographs of the Test Setup............................................................................................................ 53 Photographs of the EUT....................................................................................................................... 54 Page 4 of 54 Report No.: MTi221028005-07E1 Address: 101, No.7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Test Result Certification Applicant: Shenzhen Sipeed Technology Co, Ltd. Address: Room 401, BLDG A, Huafeng Smart Innovation Port, Gushu, Bao'an, Shenzhen, China Manufacturer: Shenzhen …

Text truncated - open the document above for the full version.

Page 1 of 2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Appendix - Test Setup Photos Model: M1A Radiated emissions – Below 30 MHz Radiated emissions –Below 1 GHz Page 2 of 2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Conducted emissions ----End of Report----