2ASHLDL-CC1310-BDL-CC1310-B Ultra-Low Power UART Wireless SoC Transceiver Module

UART Transceiver Module DL-CC1310-B ---------------------------------------------------------------------------------------------------------------------------------------------------------------- ShenZhen Dreamlnk Technology Co., Ltd Tel: 86-755-29369047 E-mail: [email protected] www.iot-rf.com 1 Ultra-Low Power UART Wireless SoC Transceiver Module SPECIFICATION Model No.: DL-CC1310-B Version: V1.12 DL-CC1310-B 915MHz UART Transceiver Module DL-CC1310-B ---------------------------------------------------------------------------------------------------------------------------------------------------------------- ShenZhen Dreamlnk Technology Co., Ltd Tel: 86-755-29369047 E-mail: [email protected] www.iot-rf.com 2 Before using this module, please pay attention to the following important matters: This module is an electrostatic sensitive product. Please operate it on an anti-static workbench during installation and testing. This DL-CC1310-B UART Wireless Module uses an external antenna by default, which is intended to be embedded in your product or application, and does equip with a metal shield itself for a better anti-interference ability. The antenna can be a wire antenna or a standard UHF antenna. You can choose a specific antenna according to the actual situation. Metal objects and wires should be kept away from the antenna as much as possible. If the product uses a metal shell, be sure to install the antenna outside the metal shell. Otherwise, the RF signal will be seriously attenuated, which will affect the effective distance. Disclaimer: This specification is just for your information, all the charts and pictures used in this specification are for reference only. The actual test shall prevail for details. We do not assume any responsibility for personal injury or property loss caused by user's improper operation. This specification is subject to change due to the continuous improvement and upgrading of the product version, and the latest version specification shall prevail. DREAMLNK reserves the right of final interpretation and modification of all contents in this specification. Copyright © Shenzhen DreamLnk Technology Co., Ltd UART Transceiver Module DL-CC1310-B ---------------------------------------------------------------------------------------------------------------------------------------------------------------- ShenZhen Dreamlnk Technology Co., Ltd Tel: 86-755-29369047 E-mail: [email protected] www.iot-rf.com 3 Revision History Date Version Formulation / Revision of Contents Approved by 2022-4-5 V1.0 DL-CC1310-B Standard Version UART Module Fagan Xu 2022-6-18 V1.1 Specification Update Fagan Xu NOTE: Page numbers for previous revisions may differ from page numbers in the current version. UART Transceiver Module DL-CC1310-B ---------------------------------------------------------------------------------------------------------------------------------------------------------------- ShenZhen Dreamlnk Technology Co., Ltd Tel: 86-755-29369047 E-mail: [email protected] www.iot-rf.com 4 Table of Contents 1. Module Overview ...................................................................................................................................... 5 1.1 Brief Introduction .............................................................................................................................. 5 1.2 Features ............................................................................................................................................. 6 1.3 Typical Application ........................................................................................................................... 7 2. Technical Parameter ................................................................................................................................. 8 3. Pin Definitions ........................................................................................................................................... 9 4. Module Dimension ................................................................................................................................... 11 5. Application Connection Diagram ........................................................................................................... 11 6. Circuit Design .......................................................................................................................................... 12 6.1 Power Supply Design ...................................................................................................................... 12 6.2 RF Routing Design .......................................................................................................................... 12 6.3 Antenna Design ............................................................................................................................... 13 UART Transceiver Module DL-CC1310-B ---------------------------------------------------------------------------------------------------------------------------------------------------------------- ShenZhen Dreamlnk Technology Co., Ltd Tel: 86-755-29369047 E-mail: [email protected] www.iot-rf.com 5 1. Module Overview 1.1 Brief Introduction DL-CC1310-B Wireless Module is an SoC embedded Serial Port RF Transceiver Module (UART Module) with AT command, which was developed by DREAMLNK based on Texas Instruments' CC1310F128RHBR (built-in dual-core ARM) Radio Frequency chip. It combines an integrated RF Controller (Cortex®-MO) and a powerful Arm® Cortex®-M3 Processor, the Clock Speed of the MCU can reach up to 48MHz. This DL-CC1310-B Wireless Module supports Narrow-band Communication, Direct Sequence Spread Spectrum (DSSS), Long-range Transmission and High-efficiency Communication. With its fully functional AT Commands, this CC1310 RF module support any Serial Baud Rate setting from 1920bps to 256000bps, which can greatly improve the communication efficiency with up to -124dBm rece…

Text truncated - open the document above for the full version.

SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 6/9/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2ASHLDL-CC1310-B FRN of applicant: 0028234334 Per section 2.911(d)(7) of the FCC rules, SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Baihetian Innovative Solutions FCC Registration Number(FRN): 0033401605 Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Stella Li Title: Manager Company Name: SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD Date: 6/9/2023 Agent Signed (if different to Applicant): Signed: Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 6/9/2023

DATE :2023-06-09 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 @ On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. L23-L28, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certiff that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission's regulations will have affixed to it a label identical to that submitted for approval with this apPlication. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, stilliesides with SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD and Block C 602, District A, Huame'lju Business Center, Xinan Street, Baoan District, Shenzhen City, Guangdong, China Company: SHENZHEN DREAMLNK TECHNOLOGY CO',LTD

Differences Declaration To whom concern, We company SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD hereby declares: The product models DL-CC1310-B 868M/915M, DL-CC1310-B are identical in the same PCB layout, interior structure and electrical circuits, the only difference is the model name for commercial purpose. Authorized signature: Date: 2023-06-16

FCC Modular Approval Request Rev 3.0 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Subject; Modular Transmitter Application Company name: SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD FCC ID: 2ASHLDL-CC1310-B Dear Sir/Madam, This letter includes the FCC application requirements for Modular Transmitter Approval Request for;- FCC KDB 996369 D01 ‘Module Certification Guide v02; and FCC KDB 996369 D03 OEM Manual v01 In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module Equip Auth Guide v02’. FCC ID: 2ASHLDL-CC1310-B has been examined against the following requirements. Requirement per 15.212 and KDB 996369 D01 Yes/No Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. yes The module have a RF shielding. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. yes The module has it’s own buffered modulation/data inputsunit. The module must contain power supply regulation on the module. yes The module has a power supply circuitry. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). yes The module has a permanently antenna. The module must demonstrate compliance in a stand-alone configuration. yes The module compliance astand-alone configuration. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748). yes The label is paste on the shield of the module. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. yes The module compliance all conditions provided in the integration instructions by the grantee. FCC Modular Approval Request Rev 3.0 The module must comply with RF exposure requirements yes The module compliance with RF exposurere quirements Name: Stella Li Date: 2023-06-09 Title: Manager Signature of applicant:

SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD DATE:2023-06-09 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC lD: 2ASHLDL-CC1 310-B proOuct Name: DL-CC131O-B Ultra-Low Power UART Wireless SoC Transceiver Module Request for Confidentialitv To Whom lt MaY Concern, pursuant to the provisions of the commission's rules Title 47 Sections $0'457 and s0.459, we are r"qr"tting the commission to withhold the following attachment(s) as Ionfidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered ", propt''"tiry intott"tion in operation of the equipment'.The public disclosure of these Oocuinents might be harmful to our company and would give competitors an unfair advantage in the market' Xschematic Diagram X Block Diagram X OPerational DescriPtion ln additional to above mentioned documents, in order to comply with the marketing r"grl;tiori in Titte 4t CFR St.803 and the importation rules in Title 47 CFR 52'1204' while ensuring that OuSn".i sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); X External Photos XTest SetuP Photos X lnternal Photos X User Manual I For 45 days, pursuant to Public Notice DA 04-1705' OR XFor 180 days pursuantto KD3726920 D01' It is our understanding that all measurement test reports, FCC lD label format and correspondence during the certiflcation review process cannot be granted as confidential documents and this iniormation will be available for public review once the grant of equipment authorization is issued' Signature: Name: Stella Li Title: Manager tdu, L;

Material: White copper. 材质: 洋白铜

Label location

FCC ID: 2ASHLDL-CC1310-B RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: 2ASHLDL-CC1310-B Test Result of RF Exposure Evaluation Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result 905MHz 12.97 19.82 0.0062 1.0 PASS Remark: antenna gain=2dBi The max power density is less than MPE exempt limit, so it is compliance.

Global United Technology Services Co., Ltd. Report No.: GTS2023030052F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 35 TEST REPORT Applicant: SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD Address of Applicant: Block C 602, District A, Huameiju Business Center, Xinan Street, Baoan District, Shenzhen City, Guangdong, China Manufacturer/Factory: SHENZHEN DREAMLNK TECHNOLOGY CO.,LTD Address of Manufacturer/Factory: Block C 602, District A, Huameiju Business Center, Xinan Street, Baoan District, Shenzhen City, Guangdong, China Equipment Under Test (EUT) Product Name: DL-CC1310-B Ultra-Low Power UART Wireless SoC Transceiver Module Model No.: DL-CC1310-B 868M/915M, DL-CC1310-B Trade Mark: FCC ID: 2ASHLDL-CC1310-B Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: March 06, 2023 Date of Test: March 07, 2023-June 09, 2023 Date of report issued: June 09, 2023 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 35 2 Version Version No. Date Description 00 June 09, 2023 Original Prepared By: Date: June 09, 2023 Project Engineer Check By: Date: June 09, 2023 Reviewer Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 35 3 Contents Page 1 COVER PAGE ................................................................................................................................................ 1 2 VERSION ........................................................................................................................................................ 2 3 CONTENTS .................................................................................................................................................... 3 4 TEST SUMMARY ........................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY .................................................................................................................. 4 5 GENERAL INFORMATION ............................................................................................................................ 5 5.1 GENERAL DESCRIPTION OF EUT ............................................................................................................... 5 5.2 TEST MODE .............................................................................................................................................. 7 5.3 TEST FACILITY .......................................................................................................................................... 7 5.4 TEST LOCATION ....................................................................................................................................... 7 5.5 DESCRIPTION OF SUPPORT UNITS ............................................................................................................. 7 5.6 DEVIATION FROM STANDARDS ................................................................................................................... 7 5.7 ABNORMALITIES FROM STANDARD CONDITIONS ......................................................................................... 7 5.8 ADDITIONAL INSTRUCTIONS ....................................................................................................................... 7 6 TEST INSTRUMENTS LIST ........................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .......................................................................................... 10 7.1 ANTENNA REQUIREMENT ......................................................................................................................... 10 7.2 CONDUCTED EMISSIONS ......................................................................................................................... 11 7.3 CONDUCTED PEAK OUTPUT POWER ........................................................................................................ 14 7.4 CHANNEL BANDWIDTH ............................................................................................................................ 15 7.5 CARRIER FREQUENCIES SEPARATION ...................................................................................................... 16 7.6 HOPPING CHANNEL NUMBER .................................................................................................................. 17 7.7 DWELL TIME ........................................................................................................................................... 18 7.8 SPURIOUS EMISSION ............................................................................................................................... 19 7.8.1 Conducted Emission Method ........................................................................................................... 19 7.8.2 Radiated Emission Method .............................................................................................................. 20 8 TEST SETUP PHOTO ..........................…

Text truncated - open the document above for the full version.

Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 9 AppendixA: 20dB Emission Bandwidth Test Result Test Mode Antenna Frequency[MHz] 20db EBW[MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 905.00 0.047 904.971 905.00.018 --- --- TX Ant1 914.72 0.048 914.692 914.740 --- --- TX Ant1 924.44 0.051 924.409 924.460 --- --- Test Graphs TX-Ant1-905.00 TX-Ant1-914.72 / TX-Ant1-924.44 / Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 9 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 905.00 0.04818 904.9708 905.00.0190 --- --- TX Ant1 914.72 0.05213 914.6913 914.7434 --- --- TX Ant1 924.44 0.05201 924.4101 924.4621 --- --- Test Graphs TX-Ant1-905.00 TX-Ant1-914.72 / TX-Ant1-924.44 / Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 9 AppendixC: Maximum conducted output power Test Result Test Mode Antenna Frequency[MHz] Result[dBm] Limit[dBm] Verdict TX Ant1 905.00 12.97 ≤30 PASS TX Ant1 914.72 12.84 ≤30 PASS TX Ant1 924.44 12.72 ≤30 PASS Test Graphs TX-Ant1-905.00 TX-Ant1-914.72 / TX-Ant1-924.44 / Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 9 AppendixD: Carrier frequency separation Test Result Test Mode Antenna Frequency[MHz] Result[MHz] Limit[MHz] Verdict TX Ant1 Hop_905.00 0.3535 ≥0.047 PASS TX Ant1 Hop_914.72 0.3612 ≥0.048 PASS TX Ant1 Hop_924.44 0.3416 ≥0.051 PASS Test Graphs TX-Ant1-Hop-905.00 TX-Ant1-Hop-914.72 / TX-Ant1-Hop-924.44 / Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 9 AppendixE: Time of occupancy Test Result Test Mode Antenna Frequency[MHz] BurstWidth [ms] TotalHops [Num] Result[s] Limit[s] Verdict TX Ant1 Hop 65.54 5 0.3277 ≤0.4 PASS Test Graphs TX-Ant1-Hop TX-Ant1-Hop Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 9 AppendixF: Number of hopping channels Test Result Test Mode Antenna Frequency[MHz] Result[Num] Limit[Num] Verdict TX Ant1 Hop 55 ≥50 PASS Test Graphs TX-Ant1-Hop Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 9 AppendixG:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 Low 905.00 13.43 -45.88 ≤-6.57 PASS TX Ant1 High 924.44 12.65 -50.25 ≤-7.35 PASS TX Ant1 Low Hop_905.00 13.26 -47.36 ≤-6.74 PASS TX Ant1 High Hop_924.44 12.59 -43.92 ≤-7.41 PASS Test Graphs TX-Ant1-905.00 TX-Ant1-924.44 TX-Ant1-Hop-905.00 TX-Ant1-Hop-924.44 Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 9 AppendixH:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] FreqRange [MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 905.00 0~Reference 13.43 13.43 --- PASS TX Ant1 905.00 30~10000 13.43 -44.16 ≤-6.57 PASS TX Ant1 914.72 0~Reference 12.69 12.69 --- PASS TX Ant1 914.72 30~10000 12.69 -44.67 ≤-7.31 PASS TX Ant1 924.44 0~Reference 12.68 12.68 --- PASS TX Ant1 924.44 30~10000 12.68 -50.02 ≤-7.32 PASS Report No.: GTS2023030052F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 9 Test Graphs TX-Ant1-905.00-0~Reference TX-Ant1-905.00-30~10000 TX-Ant1-914.72-0~Reference TX-Ant1-914.72-30~10000 TX-Ant1-924.44-0~Reference TX-Ant1-924.44-30~10000 ---End---

SPECIFICATION ShenzhenDreamLNKTechnologyCo.,Ltd. 深圳市骏晔科技有限公司 915MHzRubberRodAntenna ProductSpecification ClientNameFrequencyBand915MHz WireNameVersionV1.0 Customer’sPartNumberDreamLNK’sPartNumberW10-915M RFDesignerJamesWangRFManagerKnightAi StructuralDesignerStructuralDesignManager TechnicalDirectorDate2022-12-27 Clientconfirmation: Whethertheproductmeetsyourrequirements?□OK□NG W10-915M Theinformationprovidedbyusshouldbekeptstrictlyconfidential,anditisnotallowedtodisclosetoanyoneelseor othercompanies,withoutpriorwrittenconsent ------------------------------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------------------------------ ShenZhenDreamlnkTechnologyCo.,LtdTel:86-755-29369047E-mail:[email protected] 2 Contents Cover........................................................................................1 Contents...................................................................................2 1.Photos...................................................................................3 2.Parameters..............................................................................3 3.Testreport................................................................................4 4.Structurediagram......................................................................5 5.Environmentalreliabilityexperimentreport.....................................6 6.Contactus..............................................................................7 The informationprovidedby us shouldbe kept strictlyconfidential,and it is not allowedto discloseto anyoneelse or othercompanies, withoutprior writtenconsent ------------------------------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------------------------------ ShenZhenDreamlnkTechnologyCo.,LtdTel:86-755-29369047E-mail:[email protected] www.iot-rf.com 3 1. Photos 2. Parameters Test parameters ProductName915MHzRubberRod AntennaModelNoW10 -915M ElectricalSpecifications Freq uencyRange915 MHzPolarizationLINEAR InputImpedance50 ΩRadiationdirectionOMNI VSWR≦2.0PowerCapacity10W Gain2dBiBandwidth/ MechanicalSpecifications Dimensions10. 8cmColorBlack ConnectorModelSMA-JCableLength/ AntennaMaterial ABS & Copper StorageTemp.-10-+70°C WorkingTemperature-10°C-+60°CRelativeHumidity40~85% Theinformationprovidedbyusshouldbekeptstrictlyconfidential,anditisnotallowedtodisclosetoanyoneelseor othercompanies,withoutpriorwrittenconsent ------------------------------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------------------------------ ShenZhenDreamlnkTechnologyCo.,LtdTel:86-755-29369047E-mail:[email protected] 4 3.Testreport Theinformationprovidedbyusshouldbekeptstrictlyconfidential,anditisnotallowedtodisclosetoanyoneelseor othercompanies,withoutpriorwrittenconsent ------------------------------------------------------------------------------------------------------------------------------------------------------------ -------------------------------------------------------------------------------------------------------------------------------------------------…

Text truncated - open the document above for the full version.