2ASIVPGD638Lockly Fortis Series Smart Lock Latch Edition

Setup and Use 222 Latch EditionLatch Edition PGD638 Lockly Fortis Series We’re here to help Your Lyro smart lock comes with lifetime technical support. Feel free to contact us with any questions or comments. (669) 500-8835 [email protected] support.Lockly.com Getting to Know Your Smart Lock Install Battery Download Lockly Home App Set Up Your Lock in the Lockly Home App Add Your Lockly Fortis Series Smart Lock to Matter over Thread Digital Keypad Access Codes Safe Mode NFC Key Tag Unlock with Lockly Home App Locking/Unlocking with Physical Key More Ways to Access and Control Troubleshooting FAQs 03 04 05 06 07 08 09 10 11 12 13 14 15/16 Setup 03 Getting to Know Your Smart Lock Before setup, you can unlock the door using the default PIN 123456.These temporary methods work only during setup and disable automatically once complete. OK Button Key Cylinder Numeric Keypad LED Indicator Doorbell Button Cancel NFC Reader Battery Cover Battery Compartment (8 AA Batteries Required) SET Button Interior LED Indicator Inside Handle Exterior Handle Door Lock Button USB-C Emergency Power Port 04 Install Battery When the battery level reaches 30%, the device will enter Low Battery Mode. When the keypad is activated, the digits 20, 10 or 0 will appear for one second, indicating the remaining battery level of 20%, 10% and near depletion respectively. The red indicator light will flash for one minute along with repeated beeping alerts. Please replace the batteries promptly. Low Battery If only the digit 0 keeps flashing on the keypad, the battery is completely drained. You may connect a USB-C cable to the USB-C port on the bottom of the lock for emergency power supply to unlock the device, or use the physical key for unlocking. Install new alkaline batteries immediately after unlocking. Insert NEW alkaline batteries, matching (+) and (–) signs. Keep battery sides from touching to avoid short circuits. If a battery leaks, remove it immediately and clean the holder with a dry cloth. + - - + + - - + AA Battery 05 Download Lockly Home App Scan the QR code or visit Lockly.com/app to download the Lockly Home app. Sign up or log in to your account. The app will walk you through the final installation, configuration and profile setup for a personalized user experience. Complete Setup in the Lockly Home App 06 Open the Lockly Home app. Register a new account via "Sign Up" or log in if you already have one. Tap the + icon to add a new device. Select Lockly Smart Lock. Press the SET button to enter pairing mode. The status indicator light will flash green, with a 10-minute pairing window. Scan the barcode on the back of the lock, or choose to add the lock manually. For manual addition, select the Bluetooth device prefixed with PGD638 from the device list. Follow the in-app prompts to complete setup, then create your access credentials (PIN codes, fingerprints, etc.) following the on-screen guidance. Check Your Wi-Fi Signal Ensure the lock is installed within coverage of a strong, stable Wi-Fi signal. 2.4 GHz Wi-Fi Only This lock only works with 2.4 GHz Wi-Fi networks, so please ensure the 2.4 GHz band of your router is enabled. Enable SSID Broadcast Hidden Wi-Fi networks cannot be detected by the lock, so turn on SSID broadcast in your router configuration to allow the lock to locate your wireless network. Wi-Fi Compatibility Settings If you are using a Wi-Fi 6 (802.11ax) or Wi-Fi 7 (802.11be) router, make sure Wi-Fi 4 (802.11b/g/n) compatibility is enabled. 1. 2. 3. 4. 5. 6. SET Button Complete Setup in the Matter over Thread 07 You can connect your Lockly Fortis Series Smart Lock to smart home ecosystems including Apple Home, Google Home, Amazon Alexa and SmartThings via Matter over Thread for centralized lock management and configuration. A Thread border gateway compatible with your target platform is required beforehand. Press the SET button on the lock to enter pairing mode. The status indicator will flash green, and the pairing window will remain active for 10 minutes. Launch your smart home controller app with native Matter and Thread support. Tap to add a new device in the app, then select the Matter smart lock device type. Follow the on-screen instructions to finish device authentication and network binding to link the lock to your Matter over Thread network. During pairing, you may either scan the Matter QR code printed on the back of the lock or manually enter the 11-digit Setup PIN code as prompted to complete authentication. After successful pairing, you can remotely operate and manage your Lockly smart lock through any Matter-certified smart home platform. Matter over Thread requires a Thread Border Router. Please ensure you have a compatible and operational Thread Border Router at home, such as Apple HomePod mini, Apple TV 4K, Google Nest Hub Max, Nest Wifi Pro, 4th Gen Amazon Echo, SmartThings Station, etc. Excessive distance or walls between the Thread Border Router and the lock will weaken signals. The lock will repeatedly reconnect to the network and increase battery consumption. Keep the router close to the lock and avoid wall obstructions. If you intend to remove the smart lock from its original smart ecosystem or switch to a different ecosystem, first tap Delete Device within the original ecosystem App, then quickly press the SET button five times in a row; the lock will enter reset mode and clear all Matter configurations, and all user data and settings previously synced via Matter-certified third-party smart home platforms will be fully erased. 1. 2. 3. 4. 5. SET Button Digital Keypad 08 When the screen is off, press any number key area, or press the Cancel Button () twice. Unlock Press any key to wake up the screen. Enter your PIN code, then press the OK Button ( ) after the last digit. Lock To lock, either press the OK Button () while the screenis on. Access Codes 09 12345 6 Default PIN Code The default PIN code is 1 2 3 4 5 6. During setup, you will be prompted to set a new code to replace it…

Text truncated - open the document above for the full version.

PIN GENIE, INC. DBA LOCKLY Covered Equipment Certification Attestation Letter 7/17/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2ASIVPGD638 PIN GENIE, INC. DBA LOCKLY (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. PIN GENIE, INC. DBA LOCKLY (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. PIN GENIE, INC. DBA LOCKLY (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Cindy zho Title: COO Company Name: PIN GENIE, INC. DBA LOCKLY Date: 7/17/2026

PIN GENIE, INC. DBA LOCKLY U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: July 17, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2ASIVPGD638 PIN GENIE, INC. DBA LOCKLY(“the applicant”) certifies that, as of the date of the filing of the application, PIN GENIE, INC. DBA LOCKLY (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. PIN GENIE, INC. DBA LOCKLY ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: PIN GENIE, INC. DBA LOCKLY FRN: 0028246908 Address: 2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States Signature: Contact Person: Cindy zhou Tel: 4159109522 Email: [email protected] Applicant PIN GENIE, INC. DBA LOCKLY FRN: 0028246908 Address: 2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States Signature: Contact Person: Cindy zhou Tel: 4159109522 Email: [email protected]

DATE: July 17, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CCUT Quality Technology Co., Ltd. (1F, Building 35, Changxing Technology Indstrl Park Changzhen Community, Yutang Street, Shenzhen, China) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with PIN GENIE, INC. DBA LOCKLY (2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States). <Signature> Name: Cindy zhou Title: Manager Applicant Company: PIN GENIE, INC. DBA LOCKLY

Date: July 17, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: Cindy zhou Title: Manager Company: PIN GENIE, INC. DBA LOCKLY

DATE: July 17, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ASIVPGD638 Product Name: Lockly Fortis Series Smart Lock Latch Edition Product Model: PGD638 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Cindy zhou Title: COO Company: PIN GENIE, INC. DBA LOCKLY

Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report Annex A. EUT External Photos Model: PGD638 EUT View 1 EUT View 2 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT View 3 EUT View 4 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT View 5 EUT View 6 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT View 7 EUT View 8

Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report Annex D. Label and Inf ormation FCC Label Sample FCC Labe Size: 50mm *22mm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location Label Location

Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report Annex B. EUT Internal Photos Model: PGD638 EUT Internal View 1 EUT Internal View 2 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 3 EUT Internal View 4 BT Antenna Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 5 EUT Internal View 6 WIFI/BT Antenna Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 7 EUT Internal View 8 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 9 EUT Internal View 10 NFC Antenna Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 11 EUT Internal View 12 Report No: SSP26060175-1&2&3&4E FCC ID: 2ASIVPGD638 Annex of Test Report EUT Internal View 13 EUT Internal View 14

FCC ID: 2ASIVPGD638 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz, * = Plane-wave equivalent power density. Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation For BLE-Matter Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result BLE_1Mbps 0 0(±1) 1 1.26 0.0005 1.0 PASS For BLE Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result BLE_1Mbps -0.96 0(±1) 1 1.26 0.0006 1.0 PASS For 2.4GWiFi Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result 802.11n20 11.78 11(±1) 12 15.85 0.0075 1.0 PASS For 13.56MHz Mode Output power to antenna (dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result 13.56MHz -31.65 -31(±1) -30 0.001 0.0000002 0.9789333 PASS Field Strength: 63.55dBuV/m @3m 63.55dBuV/m -95.2=-31.65dBm Remark: antenna gain= BLE-Matter: 2.72dBi, BLE: 3.74dBi, 2.4GWiFi: 3.74dBi, 13.56MHz: 0dBi It can simultaneously use 2.4G Wi-Fi, Bluetooth BLE, Bluetooth BLE-Matter and NFC (13.56MHz) for data transmission. Calculations for simultaneously transmit Mode Ratios Result Limit Result BLE-Matter 0.0005 0.0086002 1 PASS BLE 0.0006 2.4G Wi-Fi 0.0075 13.56 0.0000002 Ratios = Power Density / Power density Limit

Report No: SSP26060175-3E FCC Test Report Page 1 of 54 FCC TEST REPORT FCC ID: 2ASIVPGD638 Report No. : SSP26060175-3E Applicant : PIN GENIE, INC. DBA LOCKLY Product Name : Lockly Fortis Series Smart Lock Latch Edition Model Name : PGD638 Test Standard : FCC Part 15.247 Date of Issue : 2026-07-02 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26060175-3E FCC Test Report Page 2 of 54 Test Report Basic Information Applicant..................................: PIN GENIE, INC. DBA LOCKLY Address of Applicant...............: 2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States Manufacturer..........................: Smart Electronic Industrial (Dong Guan) Co Ltd Address of Manufacturer........: Qing Long Road, Long Jian Tian-Cun, Huang Jiang-Zhen, Dong Guan, 523765 China Product Name.........................: Lockly Fortis Series Smart Lock Latch Edition Brand Name.............................: - Main Model..............................: PGD638 Series Models..........................: - Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020 + Cor.1-2023 Date of Test .............................: 2026-06-23 to 2026-06-30 Test Result...............................: PASS Tested By ................................: (Walker Wu) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26060175-3E FCC Test Report Page 3 of 54 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 16 5.1 Standard and Limit.............................................................................................................................................. 16 5.2 Test Procedure.................................................................................................................................................... 16 5.3 Test Data and Results .......................................................................................................................................... 18 6. Band-edge Emissions(Radiated) ............................................................................................................................... 27 6.1 Standard and Limit.............................................................................................................................................. 27 6.2 Test Procedure.................................................................................................................................................... 27 6.3 Test Data and Results .................................................................................................................................…

Text truncated - open the document above for the full version.

Report No: SSP26060175-1E FCC Test Report Page 1 of 41 FCC TEST REPORT FCC ID: 2ASIVPGD638 Report No. : SSP26060175-1E Applicant : PIN GENIE, INC. DBA LOCKLY Product Name : Lockly Fortis Series Smart Lock Latch Edition Model Name : PGD638 Test Standard : FCC Part 15.247 Date of Issue : 2026-07-02 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26060175-1E FCC Test Report Page 2 of 41 Test Report Basic Information Applicant..................................: PIN GENIE, INC. DBA LOCKLY Address of Applicant...............: 2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States Manufacturer..........................: Smart Electronic Industrial (Dong Guan) Co Ltd Address of Manufacturer........: Qing Long Road, Long Jian Tian-Cun, Huang Jiang-Zhen, Dong Guan, 523765 China Product Name.........................: Lockly Fortis Series Smart Lock Latch Edition Brand Name.............................: - Main Model..............................: PGD638 Series Models..........................: - Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020 + Cor.1-2023 Date of Test .............................: 2026-06-23 to 2026-06-30 Test Result...............................: PASS Tested By ................................: (Walker Wu) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26060175-1E FCC Test Report Page 3 of 41 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 16 5.1 Standard and Limit.............................................................................................................................................. 16 5.2 Test Procedure.................................................................................................................................................... 16 5.3 Test Data and Results .......................................................................................................................................... 18 6. Band-edge Emissions(Radiated) ............................................................................................................................... 27 6.1 Standard and Limit.............................................................................................................................................. 27 6.2 Test Procedure.................................................................................................................................................... 27 6.3 Test Data and Results .................................................................................................................................…

Text truncated - open the document above for the full version.

Report No: SSP26060175-2E FCC Test Report Page 1 of 41 FCC TEST REPORT FCC ID: 2ASIVPGD638 Report No. : SSP26060175-2E Applicant : PIN GENIE, INC. DBA LOCKLY Product Name : Lockly Fortis Series Smart Lock Latch Edition Model Name : PGD638 Test Standard : FCC Part 15.247 Date of Issue : 2026-07-02 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26060175-2E FCC Test Report Page 2 of 41 Test Report Basic Information Applicant..................................: PIN GENIE, INC. DBA LOCKLY Address of Applicant...............: 2024 Macopin Rd., Unit E, West Milford, New Jersey 07480 United States Manufacturer..........................: Smart Electronic Industrial (Dong Guan) Co Ltd Address of Manufacturer.......…

Text truncated - open the document above for the full version.