2ASLN-IDZ01BLE-B8200 BLE Logic Board

1Leviton Confidential BLE-B8200 Module – Installation Manual FCC ID of this product is as follows: FCC ID: 2ASLN-IDZ01 IC ID of this product is as follows: IC: 25037-IDZ01 This module can be used for Bluetooth protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band [2400- 2483.5 MHz]. For integration on Leviton’s end-product only – module cannot be sold to general public. Therefore we will ask end-product documentation to include the following statements required by FCC and Industry Canada (IC) on the product and in the Installation Manual Notice. 2Leviton Confidential Contents 1.Supply Voltage 2.Theory of operation 3.Module Dimensions 4.Module Footprint 5.Module Placement 6.Antenna 7.Notice 8.End-product testing 3Leviton Confidential 1. Supply Voltage Min.Typ.Max.Unit OperatingTemperature Range-40+25+85Deg. C OperatingVoltage2.85.07.5VDC •The power is provided from the 8-pin connector to the module. •The module has on-board LDO to regulate power supply. 4Leviton Confidential 2. Theory of Operation – BLE Channels BLUETOOTH Channel # Frequency (MHz) TX Power - Target MAX dBm (Dec) [Firmware Setting]Channel # Frequency (MHz) TX Power - Target MAX dBm (Dec) [Firmware Setting] 3724029.51824429.5 024049.51924449.5 124069.52024469.5 224089.52124489.5 324109.52224509.5 424129.52324529.5 524149.52424549.5 624169.52524569.5 724189.52624589.5 824209.52724609.5 924229.52824629.5 1024249.52924649.5 3824269.53024669.5 1124289.53124689.5 1224309.53224709.5 1324329.53324729.5 1424349.53424749.5 1524369.53524769.5 1624389.53624789.5 1724409.53924809.5 Frequency Tolerance: ± 20ppm 5Leviton Confidential 3. Module Dimensions •The module is of fixed dimensions and no outside changes are permitted. •Refer to ‘B8200module.dxf’ for footprint. 6Leviton Confidential 2. Module Connections •Module can only be used with another PCBs connected using the 8-pin connector. •Keep area under the antenna clear of any copper or electrolytic components. 7Leviton Confidential 4. Antenna •The module comes with an embedded chip antenna design that followed the specifications of the antenna. •About the signal line between chip and an antenna on the module •It is a 50-ohm line design. •Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. •The concrete contents of a check are the following two points. 1.An antenna gain is lower than a gain given in antenna specifications. 2.The emission level is not getting worse. 8Leviton Confidential 4. Antenna •Please refer KDB 996369 D04 Module Integration Guide for guidance, installation instructions and testing requirements. •Conducted emissions testing: RF1 BLE IC RF2RF3 C HI P Antenna U . FL . R2 R1 Option fo r Conducted Testing 9Leviton Confidential 7. Notice •For Leviton’s end-product integration only – device cannot be sold to general public. •This module can be used either for Zigbee or Bluetooth protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band [2400-2483.5 MHz]. •Therefore we will include the following statements required by FCC/ IC on the product and in the Installation Manual Notice. •Please describe the following warning on the final product which contains this module. Contains Transmitter Module: FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Contains: FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 OR Contientun module transmetteur: FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Contient: FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 OR To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and operatingin conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Pour se conformer aux limitesd'expositionaux RF de la FCC et d'IndustrieCanada pour la population générale/ exposition non contrôlée, l'antenne(s) utiliséepour cetransmetteurdoitêtreinstallépour fournirunedistance de séparationd'aumoins20 cm de toutesles personneset fonctionnantconjointementavec uneautreantenneouémetteur, saufenconformitéavec les procéduresde produitsmulti-émetteurFCC. 10Leviton Confidential 7. Notice •Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le produit décrit aux présentes est conforme aux exigences de la partie 15 des règlements de la FCC. Son utilisation est soumise aux deux conditions suivantes: (1) il ne cause aucun brouillage préjudiciable et (2) il n’est pas affecté par les interférences d’autres dispositifs susceptibles notamment d’en perturber le fonctionnement. This devicecontainslicence-exempt transmitter(s)/receiver(s) thatcomplywithInnovation, Science and EconomicDevelopment Canada’slicence-exempt RSS(s). Operationis subjectto the followingtwoconditions: 1. This devicemaynot cause interference. 2. This devicemust acceptanyinterference, includinginterferencethatmaycause undesiredoperationof the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. FCC/ ISED CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equ…

Text truncated - open the document above for the full version.

Dmitriy Moskovkin Manager Codes Standards & Compliance Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com Page 1 of 4 Applicant/Grantee Leviton Manufacturing Co Inc FCC ID: 2ASLN-IDZ01 Section 15.212 Modular Transmitters Request for Modular Approval ☐ Request for Limited Modular Approval ☒ Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The device does not meet this requirement – limited modular approval is requested. No 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. The module is tested for LE Bluetooth 5.0 protocol and all the TX-RX modulation schemes were found in compliance. Yes 3 The modular transmitter must have its own power supply regulation. The module integrates on-board linear regulator and radio circuit power supplies to maintain power supply requirements. Yes 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The module includes an integral chip antenna. There are two sets of antenna tuning values to maintain compliance for different host devices. Yes 5 The modular transmitter must be tested in a stand-a lone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). As the device has no shield limited modular applies and requires testing of the device in a representative host system. Testing has been performed on the module in three different host devices to represent a total of ten different hosts – refer to additional details at the end of this document. N/A Dmitriy Moskovkin Manager Codes Standards & Compliance Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com Page 2 of 4 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The module has a label affixed. Please see the label exhibit for the label module and end-product label. Yes 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The module is compliant with all applicable FCC rules. Detailed instructions for remaining compliance are given in the User Manual (datasheet). Yes 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The module complies with RF exposure requirement. The module’s application is intended to be used in wall mount products maintaining >20 cm distance from the user. Yes Dmitriy Moskovkin Manager Codes Standards & Compliance Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com Pag…

Text truncated - open the document above for the full version.

Dmitriy Moskovkin Manager Codes Standards & Compliance Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com Date: March 3, 2020 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; Dmitriy Moskovkin Manager Codes Standards & Compliance Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Dmitriy Moskovkin Manager Codes Standards & Compliance Energy Management Control & Automation Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: (503) 404-5570

Dmitriy Moskovkin Manager Codes Standards & Compliance Energy Management Control & Automation Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ASLN-IDZ01 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna Specification Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180 days from the date of grant: External Photos Internal Photos Test Setup Photos User Manual Dmitriy Moskovkin Manager Codes Standards & Compliance Energy Management Control & Automation Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: 503 404-5570 www.leviton.com It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Dmitriy Moskovkin Manager Codes Standards & Compliance Energy Management Control & Automation Leviton Manufacturing Co., Inc. 20497 SW Teton Ave. Tualatin, OR 97062 T: (503) 404-5570

FCC Label Location The label will be permanently affixed at a fixed location on the device. ID Location Product ID Label Size Product Label

NVLAP LAB CODE 200246-0 FCC Part 1 Subpart I FCC Part 2 Subpart J RSS 102 ISSUE 5 RF EXPOSURE REPORT FOR BLE-B8200 BLE LOGIC BOARD MODEL NUMBER: BLE-B8200 MODULAR LOGIC BOARD FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 REPORT NUMBER: R13048573-E3 ISSUE DATE: 2020-04-17 Prepared for LEVITON MFG CO INC 20497 SW TETON PO BOX 2210 TUALATIN, OR 97062-2210 Prepared by UL LLC 12 LABORATORY DR. RESEARCH TRIANGLE PARK, NC 27709 USA TEL: (919) 549-1400 REPORT NO: R13048573-E3 DATE: 2020-04-17 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 2 of 10 UL LLC FORM NO: 03-EM-F00858 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC. REVISION HISTORY Ver. Issue Date Revisions Revised By 1 2020-03-11 Initial Issue Brian T. Kiewra 2 2020-03-27 Revised antenna gain and separation distance Brian T. Kiewra 3 2020-04-17 Revised average declared power to match operational description Brian T. Kiewra REPORT NO: R13048573-E3 DATE: 2020-04-17 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 3 of 10 UL LLC FORM NO: 03-EM-F00858 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC. TABLE OF CONTENTS REVISION HISTORY ..................................................................................................................2 TABLE OF CONTENTS .............................................................................................................3 1. ATTESTATION OF TEST RESULTS ..................................................................................4 2. TEST METHODOLOGY ......................................................................................................5 3. REFERENCES ....................................................................................................................5 4. FACILITIES AND ACCREDITATION ..................................................................................5 5. MAXIMUM PERMISSIBLE EXPOSURE (LIMITS AND EQUATIONS) ................................6 5.1. FCC RULES .................................................................................................................6 5.2. ISED RULES ................................................................................................................7 5.3. EQUATIONS .................................................................................................................8 6. RF EXPOSURE RESULTS ................................................................................................10 END OF TEST REPORT ..........................................................................................................10 REPORT NO: R13048573-E3 DATE: 2020-04-17 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 4 of 10 UL LLC FORM NO: 03-EM-F00858 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Leviton Mfg Co. Inc. 20497 SW Teton PO Box 2210 Tualatin, OR 97062-2210, USA MODEL: BLE-B8200 EUT DESCRIPTION: BLE-B200 Modular Logic Board SERIAL NUMBER: Non-serialized DATE RECEIVED: 2020-01-24 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Complies RSS 102 ISSUE 5 Complies UL LLC tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. All samples tested were in good operating condition throughout the entire test program. Measurement Uncertainties are published for informational purposes only and were not taken into account unless noted otherwise. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. government. Approved & Released For UL LLC By: Prepared By: Jeffrey Moser Brian T. Kiewra Operations Manager Project Engineer Consumer Technology Division Consumer Technology Division UL LLC UL LLC REPORT NO: R13048573-E3 DATE: 2020-04-17 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 5 of 10 UL LLC FORM NO: 03-EM-F00858 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC. 2. TEST METHODOLOGY All calculations were made in accordance with FCC Parts 1.1310, 2.1091, 2.1093, KDB 447498 D01 v06, KDB 447498 D03 V01, IEEE Std C95.1-2005, IEEE Std C95.3-2002, IC Safety Code 6 and RSS 102 Issue 5. 3. REFERENCES All measurements were made as documented in test report UL LLC test report R13048573-E1 for operation in the 2.4 GHz. Output power, Duty cycle and Antenna gain data is excerpted from the manufacturer’s documents. 4. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 12 Laboratory Dr., Research Triangle Park, NC 27709, USA and 2800 Perimeter Park Dr., Suite B, Morrisville, NC 27560, USA. UL LLC (RTP) is accredited by NVLAP, Laboratory Code 200246-0. REPORT NO: R13048573-E3 DATE: 2020-04-17 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 6 of 10 UL LLC FORM NO: 03-EM-F00858 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC. 5. MAXIMUM PERMISSIBLE EXPO…

Text truncated - open the document above for the full version.

NVLAP Lab code: 200246-0 CERTIFICATION TEST REPORT Report Number. : R13048573-E1 Applicant : LEVITON MFG CO INC 20497 SW TETON PO BOX 2210 TUALATIN, OR 97062-2210 Model : BLE-B8200 Modular Logic Board FCC ID : 2ASLN-IDZ01 IC : 25037-IDZ01 EUT Description : BLE-8200 BLE Logic Board Test Standard(s) : FCC 47 CFR PART 15 SUBPART C ISED RSS-247 ISSUE 2 ISED RSS-GEN ISSUE 5 Date Of Issue: 2020-06-12 Prepared by: UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 U.S.A. Tel: (919) 549-1400 REPORT NO: R13048573-E1 DATE: 2020-06-12 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 2 of 80 UL LLC 12 Laboratory Dr., RTP, NC 27709; USA TEL:(919)-549-140 This report shall not be reproduced except in full, without the written approval of UL LLC REPORT REVISION HISTORY Rev. Issue Date Revisions Revised By 1 2020-03-04 Initial Issue Cristian Melara 2 2020-03-27 Updated Antenna gain to 1.5dBi Cristian Melara 3 2020-06-12 Updated all output power values Cristian Melara REPORT NO: R13048573-E1 DATE: 2020-06-12 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 3 of 80 UL LLC 12 Laboratory Dr., RTP, NC 27709; USA TEL:(919)-549-140 This report shall not be reproduced except in full, without the written approval of UL LLC TABLE OF CONTENTS REPORT REVISION HISTORY ..................................................................................................2 TABLE OF CONTENTS .............................................................................................................3 1. ATTESTATION OF TEST RESULTS ..................................................................................5 2. TEST METHODOLOGY ......................................................................................................6 3. FACILITIES AND ACCREDITATION ..................................................................................6 4. CALIBRATION AND UNCERTAINTY .................................................................................7 4.1. MEASURING INSTRUMENT CALIBRATION ...............................................................7 4.2. SAMPLE CALCULATION .............................................................................................7 4.3. MEASUREMENT UNCERTAINTY ................................................................................7 5. EQUIPMENT UNDER TEST ................................................................................................8 5.1. EUT DESCRIPTION .....................................................................................................8 5.2. MAXIMUM OUTPUT POWER .......................................................................................8 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ...............................................................8 5.4. SOFTWARE AND FIRMWARE .....................................................................................8 5.5. WORST-CASE CONFIGURATION AND MODE ...........................................................8 5.6. DESCRIPTION OF TEST SETUP .................................................................................9 6. MEASUREMENT METHOD...............................................................................................11 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................12 8. ANTENNA PORT TEST RESULTS ...................................................................................14 8.1. ON TIME AND DUTY CYCLE .....................................................................................14 8.2. 99% BANDWIDTH ......................................................................................................15 8.2.1. ODD10-000-IDZ ...................................................................................................15 8.3. 6 dB BANDWIDTH ......................................................................................................16 8.3.1. ODD10-000-IDZ ...................................................................................................17 8.4. OUTPUT POWER .......................................................................................................18 8.4.1. ODD10-000-IDZ ...................................................................................................18 8.4.2. ODS15-000-IDZ ...................................................................................................18 8.4.3. ODD24-000-IDZ ...................................................................................................19 8.5. AVERAGE POWER ....................................................................................................20 8.5.1. ODD10-000-IDZ ...................................................................................................20 8.5.2. ODS15-000-IDZ ...................................................................................................20 8.5.3. ODD24-000-IDZ ...................................................................................................21 8.6. POWER SPECTRAL DENSITY ..................................................................................22 REPORT NO: R13048573-E1 DATE: 2020-06-12 FCC ID: 2ASLN-IDZ01 IC: 25037-IDZ01 Page 4 of 80 UL LLC 12 Laboratory Dr., RTP, NC 27709; USA TEL:(919)-549-140 This report shall not be reproduced except in full, without the written approval of UL LLC 8.6.1. ODD10-000-IDZ ...................................................................................................23 8.7. CONDUCTED SPURIOUS EMISSIONS .....................................................................24 8.7.1. ODD-10-000-IDZ .................................................................................................25 9. RADIATED TEST RESULTS .............................................................................................26 9.1. LIMITS AND PROCEDURE ........................................................................................26 9.2. TRANSMITTER ABOVE 1 GHz ..............…

Text truncated - open the document above for the full version.

NVLAP Lab code: 200246-0 SETUP PHOTOS EXHBIT Report Number. : R13048573-E1 Applicant : LEVITON MFG CO INC 20497 SW TETON PO BOX 2210 TUALATIN, OR 97062-2210 Model : BLE-B8200 Modular Logic Board FCC ID : 2ASLN-IDZ01 IC : 25037-IDZ01 EUT Description : BLE-8200 BLE Logic Board Test Standard(s) : FCC 47 CFR PART 15 SUBPART C ISED RSS-247 ISSUE 2 ISED RSS-GEN ISSUE 5 Date Of Issue: 2020-03-04 Prepared by: UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 U.S.A. Tel: (919) 549-1400 REPORT NO: R13048573-EP1 DATE: 2020-03-04 FCC …

Text truncated - open the document above for the full version.