2ASNS2501Two Way Radio

462.55-462.725MHz 467.55-467.725MHz GMRS FCC Compliance information This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. (Licensed radios are applicable); This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (Other devices are applicable) (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: January 20, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2ASNS2501 Shenzhen Retevis Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Name: Dongfang Shen Title: Manager

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: January 20, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2ASNS2501 Shenzhen Retevis Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Name: Dongfang Shen Title: Manager

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date:2026-01-20 Ref: Attestation Statements, US agent designation FCC ID: 2ASNS2501 FRN: 0028298024 Shenzhen Retevis Technology Co., Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment above for which authorization is sought. Contact: Liuye Li Company U.S. agent: RETEVIS INC Physical U.S. address of agent: 1733 E BROOKPORT ST,COVINA,CA 91724,United States FRN of U.S. agent: 0033657701 Email address of U.S. agent: [email protected] Phone of U.S. agent: 626-362-2594 RETEVIS INC acknowledges their obligation to accept service of process on behalf of Shenzhen Retevis Technology Co., Ltd. Shenzhen Retevis Technology Co., Ltd. accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. This acceptance will be in effect till the applicant decides to change the agent of service of process. By signing this form, we confirm the above and that we are aware of the application requirements listed under §2.911(d)(7). Sincerely, Signature Signature Name: Dongfang Shen Name: Liuye LI Titel: Manager Title: Directing Manager Shenzhen Retevis Technology Co., Ltd. RETEVIS INC Email: [email protected] Tel: +86-755-23481953

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-01-20 Subject; Request for Confidentiality FCC ID: 2ASNS2501 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Dongfang Shen Title: Manager

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Agent Authorization Company: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Product Name: Two Way Radio Model Number(s): RT29 Product Description: Two Way Radio We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: January 20, 2026 Name: Dongfang Shen Company: Shenzhen Retevis Technology Co., Ltd.

Report No.: AGC00319251101AP02 Page 1 of 5 EXTERNAL PHOTOS Black prototype All View of EUT UHF Antenna Report No.: AGC00319251101AP02 Page 2 of 5 Top View of EUT Bottom View of EUT Report No.: AGC00319251101AP02 Page 3 of 5 Front View of EUT Back View of EUT Report No.: AGC00319251101AP02 Page 4 of 5 Left View of EUT Right View of EUT Report No.: AGC00319251101AP02 Page 5 of 5 Port View of EUT Charger of EUT ****************************************End of Report*************************************

FCC ID Label Location 30mm&40mm FCC ID: 2ASNS2501

Report No.: AGC00319251101AP02 Page 1 of 8 INTERNAL PHOTOS Open View-1 of EUT Open View-2 of EUT Report No.: AGC00319251101AP02 Page 2 of 8 Internal View-1 of EUT Internal View-2 of EUT Report No.: AGC00319251101AP02 Page 3 of 8 Internal View-3 of EUT Internal View-4 of EUT Report No.: AGC00319251101AP02 Page 4 of 8 Internal View-5 of EUT Internal View-6 of EUT Report No.: AGC00319251101AP02 Page 5 of 8 Internal View-7 of EUT Internal View-8 of EUT Report No.: AGC00319251101AP02 Page 6 of 8 Internal View-9 of EUT Internal View-10 of EUT Report No.: AGC00319251101AP02 Page 7 of 8 Internal View-11 of EUT Internal View-12 of EUT Report No.: AGC00319251101AP02 Page 8 of 8 Battery of EUT ****************************************End of Report*************************************

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

Page 1 of 47 SAR Test Report Report No.: AGC00319251101FH01 FCC ID : 2ASNS2501 PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : RT29 APPLICANT : Shenzhen Retevis Technology Co., Ltd. DATE OF ISSUE : Jan. 06, 2026 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC00319251101FH01 Page 2 of 47 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jan. 06, 2026 Valid Initial Release Report No.: AGC00319251101FH01 Page 3 of 47 Test Report Applicant Name Shenzhen Retevis Technology Co., Ltd. Applicant Address 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Manufacturer Name Shenzhen Retevis Technology Co., Ltd. Manufacturer Address 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Factory Name N/A Factory Address N/A Product Designation Two Way Radio Brand Name RETEVIS Test Model RT29 Series Model N/A Declaration of Difference N/A EUT Voltage DC7.4 V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 Date of receipt of test item Nov. 20, 2025 Test Date Dec. 03, 2025 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Jan. 06, 2026 Reviewed By Jack Gui (Reviewer) Jan. 06, 2026 Approved By Angela Li (Authorized Officer) Jan. 06, 2026 Report No.: AGC00319251101FH01 Page 4 of 47 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 6.2. SAR SYSTEM CHECK ................................................................................................................................... 18 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 23 12. POWER MEASUREMENT ...............................................................................…

Text truncated - open the document above for the full version.

Page 1 of 58 FCC Test Report Report No.: AGC00319251101FR01 FCC ID : 2ASNS2501 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : RT29 APPLICANT : Shenzhen Retevis Technology Co., Ltd. DATE OF ISSUE : Jan. 13, 2026 STANDARD(S) : FCC Part 95 Subpart E REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC00319251101FR01 Page 2 of 58 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jan. 13, 2026 Valid Initial Release Report No.: AGC00319251101FR01 Page 3 of 58 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 7 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 8 2.4 Test Methodology ...................................................................................................................................... 8 2.5 Calculation of Emission Indicators ............................................................................................................ 8 2.6 Special Accessories .................................................................................................................................. 8 2.7 Equipment Modifications ........................................................................................................................... 8 2.8 Antenna Requirement ............................................................................................................................... 9 3. Test Environment .......................................................................................................................................... 10 3.1 Address of The Test Laboratory .............................................................................................................. 10 3.2 Test Facility .............................................................................................................................................. 10 3.3 Environmental Conditions ....................................................................................................................... 11 3.4 Measurement Uncertainty ....................................................................................................................... 11 3.5 List of Equipment Used ........................................................................................................................... 12 4. System Test Configuration ........................................................................................................................... 13 4.1 EUT Configuration ................................................................................................................................... 13 4.2 EUT Exercise ........................................................................................................................................... 13 4.3 Configuration of Tested System .............................................................................................................. 13 4.4 Equipment Used in Tested System ......................................................................................................... 13 4.5 Summary of Test Results ........................................................................................................................ 14 5. Description of Test Modes ........................................................................................................................... 15 6. Frequency Stability ....................................................................................................................................... 16 6.1 Provisions Applicable .............................................................................................................................. 16 6.2 Measurement Procedure ......................................................................................................................... 16 6.3 Measurement Setup ................................................................................................................................ 16 6.4 Measurement Result ............................................................................................................................... 17 7. 26dB Emission Bandwidth and 99% Occupied Bandwidth ...................................................................... 18 7.1 Provisions Applicable .............................................................................................................................. 18 7.2 Measurement Procedure ......................................................................................................................... 18 7.3 Measurement Setup ................................................................................................................................ 18 7.4 Measurement Result ............................................................................................................................... 19 8. Spurious Radiated Emission ......................................................................................................................... 23 8.1 Provisions Applicable .......................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC00319251101FR01 Page 50 of 58 12.5kHz, FM modulation, Assigned Frequency:462.6375MHz, 0.5W 12.5kHz, FM modulation, Assigned Frequency:462.6500MHz, 0.5W 12.5kHz, FM modulation, Assigned Frequency:467.6500MHz, 0.5W Report No.: AGC00319251101FR01 Page 51 of 58 12.5kHz, FM modulation, Assigned Frequency:467.6375MHz, 0.5W 25kHz, FM modulation, Assigned Frequency:462.6375MHz, 4W 25kHz, FM modulation, Assigned Frequency:462.6500MHz, 4W Report No.: AGC00319251101FR01 Page 52 of 58 25kHz, FM modulation, Assigned Frequency:467.6500MHz, 4W 25kHz, FM modulation, Assigned Frequency:462.6375MHz, 0.5W 25kHz, FM modulation, Assigned Frequency:462.6500MHz, 0.5W Report No.: AGC00319251101FR01 Page 53 of 58 25kHz, FM modulation, Assigned Frequency:467.6500MHz, 0.5W Report No.: AGC00319251101FR01 Page 54 of 58 12. Audio Low Pass Filter Response 12.1 Provisions Applicable §95.1775 GMRS modulation requirements Audio filter. Each GMRS transmitter type must include audio frequency low pass filtering, unless it complies with the applicable paragraphs of §95.1779 (without filtering). The filter must be between the modulation limiter and the modulated stage of the transmitter. At any frequency (f in kHz) between 3 and 20 kHz, the filter must have an attenuation of at least 60 log (f/3) dB more than the attenuation at 1 kHz. Above 20 kHz, it must have an attenuation of at least 50 dB more than the attenuation at 1 kHz 12.2 Measurement Procedure 1. The DUT transmitter output port was connected to Modulation Analyzer. 2. Path loss for the measurement included. 3. Press 23.1SPCL on modulation analyzer to enable the external LO from SIgen. 4. Set the Sigen frequency to Fc + 1.5MHz, RF output level to 0dBm without modulation. 5. Transmit the radio and set the audio analyzer to 1 kHz audio frequency and 60% of the maximum deviation. 6. Up the amplitude by 20dB. 7. On DSA, get the reference point to 0dB. 8. Vary the frequency on audio analyzer from 3 kHz to 30 kHz, record the audio tone from DSA. 12.3 Measurement Setup Report No.: AGC00319251101FR01 Page 55 of 58 12.4 Measurement Result 12.5kHz, FM modulation, Assigned Frequency:462.6375MHz-4W Audio Frequency (kHz) Response Attenuation (dB) Limit (dB) 1 0 / 3 -2.11 0.00 4 -10.26 -5.00 5 -15.21 -8.87 6 -20.55 -12.04 7 -25.41 -14.72 8 -28.45 -17.04 9 -31.44 -19.08 10 -34.37 -20.92 15 -37.63 -28.00 20 -35.51 -28.00 30 -34.36 -28.00 50 -33.22 -28.00 70 -31.96 -28.00 Report No.: AGC00319251101FR01 Page 56 of 58 25kHz, FM modulation, Assigned Frequency:462.6375MHz-4W Audio Frequency (kHz) Response Attenuation (dB) Limit (dB) 1 0 / 3 -2.52 0.00 4 -12.33 -5.00 5 -17.83 -8.87 6 -22.45 -12.04 7 -29.24 -14.72 8 -31.82 -17.04 9 -34.59 -19.08 10 -37.13 -20.92 15 -38.53 -28.00 20 -36.88 -28.00 30 -34.74 -28.00 50 -32.78 -28.00 70 -30.36 -28.00 Note: All the test frequencies was tested, but only the worst data be recorded in this part. Report No.: AGC00319251101FR01 Page 57 of 58 Appendix I: Photographs of Test Setup Refer to the Report No.: AGC00319251101AP01 Appendix II: Photographs of Test EUT Refer to the Report No.: AGC00319251101AP02 Report No.: AGC00319251101FR01 Page 58 of 58 Conditions of Issuance of Test Reports 1. All samples and goods are accepted by the Attestation of Global Compliance (Shenzhen) Co., Ltd (the “Company”) solely for testing and reporting in accordance with the following terms and conditions. The company provides its services on the basis that such terms and conditions constitute express agreement between the company and any person, firm or company requesting its services (the “Clients”). 2. Any report issued by Company as a result of this application for testing services (the “Report”) shall be issued in confidence to the Clients and the Report will be strictly treated as such by the Company. It may not be reproduced either in its entirety or in part and it may not be used for advertising or other unauthorized purposes without the written consent of the Company. The Clients to whom the Report is issued may, however, show or send it, or a certified copy thereof prepared by the Company to its customer, supplier or other persons directly concerned. The Company will not, without the consent of the Clients, enter into any discussion or correspondence with any third party concerning the contents of the Report, unless required by the relevant governmental authorities, laws or court orders. 3.The Company shall not be called or be liable to be called to give evidence or testimony on the Report in a court of law without its prior written consent, unless required by the relevant governmental authorities, laws or court orders. 4. In the event of the improper use of the report as determined by the Company, the Company reserves the right to withdraw it, and to adopt any other additional remedies which may be appropriate. 5. Samples submitted for testing are accepted on the understanding that the Report issued cannot form the basis of, or be the instrument for, any legal action against the Company. 6. The Company will not be liable for or accept responsibility for any loss or damage however arising from the use of information contained in any of its Reports or in any communication whatsoever about its said tests or investigations. 7.Clients wishing to use the Report in court proceedings or arbitration shall inform the Company to that effect prior to submitting the sample for testing. 8. The Company is not responsible for recalling the electronic version of the original report when any revision is made to them. The Client assumes the responsibility to providing the revised version to any interested party who uses them. 9. Subject to the variable length of retention time for test data and report stored hereinto as otherwise specifically required by individual accreditation authorities, the Company will only keep the supporting test data and information of the test report for a period of six years. The data and information will be disposed of after the aforemen…

Text truncated - open the document above for the full version.

Report No.: AGC00319251101AP01 Page 1 of 2 TEST SETUP PHOTOS Radiated Emission Test Setup Below 1GHz Radiated Emission Test Setup Above 1GHz Report No.: AGC00319251101AP01 Page 2 of 2 GMRS Conducted Test Setup ****************************************End of Report*************************************