2ASNSEZ09Two Way Radio

EZTalk 5 User Manual Brochures, Software/Firmware, Manual etc, Please contact Contents Important Notice to Users ........................................... Getting Started .............................................................. Screen Display................................................................. Knowing Your Radio....................................................... Menu Overview................................................................ Function Description ..................................................... Mobile App Functions ................................................... CTCSS/DCS ..................................................................... Specifications ................................................................. CAUTION ........................................................................ GUARANTEE ................................................................... 01 02 03 05 07 11 15 23 26 27 32 Important Notice to Users Unboxing Inspection Before use, please open the packaging box and carefully inspect the host unit and included accessories. If any items are missing or damaged during transportation, please contact the delivery personnel or dealer immediately. Battery Information Charging Precautions Charge new batteries or batteries that have not been used for an extended period before initial use. Performing two or three charge/discharge cycles will optimize battery capacity. When low battery power is detected, charge or replace the battery. Compatible Battery Types Use only batteries specified by the manufacturer. Using other batteries may cause explosion, resulting in injury. Note: 1. Do not short-circuit the battery terminals or dispose of batteries in fire. Do not disassemble the battery pack casing. 2. The ambient temperature during charging should be between 0°C and 40°C. Charging outside this range may affect proper charging. 3. Turn off the radio power during charging. Using the radio while charging may interfere with proper battery charging. 4. Avoid unplugging the power adapter or removing the battery during the charging process, as this may disrupt the charging program. 5. If the usage time is significantly reduced even after a full charge, it indicates the battery has reached the end of its life and should be replaced. 6. Do not disconnect and then reconnect a fully charged battery for additional charging, as this may shorten battery life or cause damage. 7. Do not charge wet batteries or radios. Dry them with a cloth before charging to avoid hazards. 8. Eliminating the Risk, keep away from the flammable materials,heat sources and ignition sources while a battery is charged. Charging should only take place in a well ventilated area and when someone is about to be aware and react to a potential issue. 9. To reduce risk of fire, a battery should not be charged for more than 3 hours and disconnect charger from line voltage (AC outlet) by removing main plug even if the batter is not completely charged.Don't leave a device unattended while charging. Disconnect the charger when the device is fully charged: do not overcharge the device. Warning： All batteries can cause damage or injury if conductive materials like jewelry, keys, or chains touch the terminals. These items can short-circuit the battery, generating significant heat. Handle all batteries with care, especially when placing them in pockets, bags, or containers with metal objects 1 Charging Procedure 1. Plug the provided adapter (standard output 5V DC) into a power outlet. 2. Place the radio with the battery installed onto the charging dock. 3. Ensure the battery contacts the charging pins correctly. The charger indicator will turn red, indicating charging has started. For Type-C charging, insert the Type-C plug into the Type-C charging port on the right side of the radio. A green battery icon on the display indicates a full charge. 4. When the charger indicator light turns green, charging is complete. You can now remove the battery or radio for use. Note: Do not use the radio while charging. Ensure the radio is turned off during charging. Maintenance and Cleaning 1. Do not hold the radio by the antenna or external microphone. 2. Wipe dust and stains from the radio with a lint-free cloth to prevent poor contact. 3. When the radio is not in use, keep the earphone jack cover closed. 4. After prolonged use, the keys, control knobs, and casing may become dirty. Clean them with a mild detergent (do not use strong corrosive chemicals) and a damp cloth. I. Getting Started Installing the Antenna 1.Place the antenna onto the antenna connector and turn it clockwise to tighten. Installing the Battery 1. Place the battery into the battery compartment. 2. Tighten the two screws clockwise to close the battery cover securely. Note: Tighten all screws when installing the battery to ensure waterproof performance. Radio Battery Level 1. Full battery bars【 】indicate sufficient power. When the battery indicator 【 】shows zero bars, the device enters low-battery mode, issuing warnings via a low-battery alert tone and a battery icon. Power On/Off 1. Press and hold the【 】key to turn the radio on or off. Volume Adjustment 1. In standby mode, briefly press the【 】key to enter the volume adjustment interface. Use the Up“ ”and Down“ ”keys to adjust the volume level. Making a Call 1. For communication, all radios in your group must be set to the same channel frequency and sub-tone code. 2. During a call, the transmitting radio should press and hold the [PTT] key to speak. 2 The screen will display "A BAND TX" or "B BAND TX", and the red LED will light up. Simultaneously, the receiving radio's screen will display "A BAND RX" or "B BAND RX", and the green LED will light up. For optimal call quality, hold the microphone 3-5 cm from your mouth while speaking. II. Screen Display 3 NO. 1 Signal Strength. Indicates current signal level for judging communication quality. Icon/TextDescription 4 Heads…

Text truncated - open the document above for the full version.

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: Mar. 12, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2ASNSEZ09 Shenzhen Retevis Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Name: Dongfang Shen Title: Manager

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China 1 | P a g e Attestation Statements To: Federal Communications Commission Date: Mar. 12, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2ASNSEZ09 Product Name: Two Way Radio This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature Printed Name: Dongfang Shen Title: Manager Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. The MCU “ HC32F460KETA“, The RF chip “ BK4819“ don’t support the mentioned function. ☐ The Memory used is limited to run the Cybersecurity or anti-virus software. The memory size is XXX, so don’t support the mentioned function. ☐ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. The storage capacity is XXX, so don’t support the mentioned function. ☐ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. The Operating system “XXX“ don’t support the mentioned function. Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check SBOM (Software Bill of Materials) [For Device is not Inherent compliance] Section Component Name Version Supplier 1 2 3

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Mar. 12, 2026 Ref: Attestation Statements, US agent designation FCC ID: 2ASNSEZ09 FRN: 0028298024 Shenzhen Retevis Technology Co., Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment above for which authorization is sought. Contact: Liuye Li Company U.S. agent: RETEVIS INC Physical U.S. address of agent: 1733 E BROOKPORT ST,COVINA,CA 91724,United States FRN of U.S. agent: 0033657701 Email address of U.S. agent: [email protected] Phone of U.S. agent: 626-362-2594 RETEVIS INC acknowledges their obligation to accept service of process on behalf of Shenzhen Retevis Technology Co., Ltd. Shenzhen Retevis Technology Co., Ltd. accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. This acceptance will be in effect till the applicant decides to change the agent of service of process. By signing this form, we confirm the above and that we are aware of the application requirements listed under §2.911(d)(7). Sincerely, Signature Signature Name: Dongfang Shen Name: Liuye LI Titel: Manager Title: Manager Shenzhen Retevis Technology Co., Ltd. RETEVIS INC

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Mar. 12, 2026 Subject; Request for Confidentiality FCC ID: 2ASNSEZ09 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Dongfang Shen Title: Manager

Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Mar. 12, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2ASNSEZ09 I, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Attestation of Global Compliance (Shenzhen) Co., Ltd) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with Shenzhen Retevis Technology Co., Ltd. We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, Full name of contact person listed on FCC’s website: Dongfang Shen Title: Manager Tel: +86-755-23481953 Fax: +86-755-23481953 Email: [email protected]

Report No.: AGC00319260204AP02 Page 1 of 5 EXTERNAL PHOTOS All View of EUT Top View of EUT UHF Antenna Report No.: AGC00319260204AP02 Page 2 of 5 Bottom View of EUT Front View of EUT Report No.: AGC00319260204AP02 Page 3 of 5 Back View of EUT Left View of EUT Report No.: AGC00319260204AP02 Page 4 of 5 Right View of EUT Port-1 View of EUT Report No.: AGC00319260204AP02 Page 5 of 5 Port-2 View of EUT ****************************************End of Report*************************************

FCC ID Label Location 20mm*30mm FCC ID: 2ASNSEZ09

Report No.: AGC00319260204AP02 Page 1 of 9 INTERNAL PHOTOS Open View-1 of EUT Open View-2 of EUT Report No.: AGC00319260204AP02 Page 2 of 9 Internal View-1 of EUT Internal View-2 of EUT GPS Antenna Report No.: AGC00319260204AP02 Page 3 of 9 Internal View-3 of EUT Internal View-4 of EUT Report No.: AGC00319260204AP02 Page 4 of 9 Internal View-5 of EUT Internal View-6 of EUT Report No.: AGC00319260204AP02 Page 5 of 9 Internal View-7 of EUT Internal View-8 of EUT Report No.: AGC00319260204AP02 Page 6 of 9 Internal View-9 of EUT Internal View-10 of EUT Report No.: AGC00319260204AP02 Page 7 of 9 Internal View-11 of EUT Internal View-12 of EUT Report No.: AGC00319260204AP02 Page 8 of 9 Internal View-13 of EUT Internal View-14 of EUT Report No.: AGC00319260204AP02 Page 9 of 9 Internal View-15 of EUT Battery View of EUT ****************************************End of Report************************************* BT Antenna

Page 1 of 19 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 19 Page 3 of 19 Page 4 of 19 Page 5 of 19 Page 6 of 19 Page 7 of 19 Page 8 of 19 Page 9 of 19 Page 10 of 19 DAE CALIBRATION DATA Page 11 of 19 Page 12 of 19 Page 13 of 19 DIPOLE CALIBRATION DATA Page 14 of 19 Page 15 of 19 Page 16 of 19 Page 17 of 19 Page 18 of 19 Page 19 of 19

Page 1 of 51 SAR Test Report Report No.: AGC00319260204FH01 FCC ID : 2ASNSEZ09 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : EZTalk 5 APPLICANT : Shenzhen Retevis Technology Co., Ltd. DATE OF ISSUE : Mar. 12, 2026 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC00319260204FH01 Page 2 of 51 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 12, 2026 Valid Initial Release Report No.: AGC00319260204FH01 Page 3 of 51 Test Report Applicant Name Shenzhen Retevis Technology Co., Ltd. Applicant Address 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Manufacturer Name Shenzhen Retevis Technology Co., Ltd. Manufacturer Address 7/F, 13-C, Zhonghaixin Science &Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Factory Name N/A Factory Address N/A Product Designation Two Way Radio Brand Name RETEVIS Test Model EZTalk 5 Series Model N/A Declaration of Difference N/A EUT Voltage DC7.4 V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 Date of receipt of test item Feb. 02, 2026 Test Date Feb. 27, 2026 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Mar. 12, 2026 Reviewed By Jack Gui (Reviewer) Mar. 12, 2026 Approved By Angela Li (Authorized Officer) Mar. 12, 2026 Report No.: AGC00319260204FH01 Page 4 of 51 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 6.2. SAR SYSTEM CHECK ................................................................................................................................... 18 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 23 12. POWER MEASUREMENT ..............................…

Text truncated - open the document above for the full version.

根 通 通 信 技 术 有 限 公 司 Gentong Communication Technology Co.,Ltd Address: 5th Floor, Building 7, Fujian Branch, Nan'an National University Science Park, Quanzhou City, China. Tel: 15889795946 Gentong Communication Technology Co.,Ltd BT antenna report Project Name:BTA512 Frequency band:2400-2500MHz Antenna：PCBA Version：R:A 根 通 通 信 技 术 有 限 公 司 Gentong Communication Technology Co.,Ltd Address: 5th Floor, Building 7, Fujian Branch, Nan'an National University Science Park, Quanzhou City, China. Tel: 15889795946 1 ﹑Passive testing fixture Purpose: To test the passive parameters of the antenna as accurately as possible. Production method: The mobile phone manufacturing tool uses a 50 ohm coaxial cable, with one end connected to the test point at the back end of the matching circuit (RF test hole front end) of the mobile phone motherboard, and the other end connected to an SMA connector. 2 ﹑ S11 testing S11 Test Method Description: Test equipment: network analyzer (Agilent 8753D) Test method: Use a 50 ohm CABLE cable to export from the instrument test port, calibrate with a calibration piece, and connect to the SMA connector of the mobile phone tool. Record the corresponding return loss and standing wave ratio at the relevant frequency points. The test schematic is as follows: 3 ﹑ S11 parameters BT antenna Frequency（MHZ） 2400 2450 2500 Return loss (dB) -8.57 -22.66 -9.83 Standing wave ratio 1.3 1.26 1.29 根 通 通 信 技 术 有 限 公 司 Gentong Communication Technology Co.,Ltd Address: 5th Floor, Building 7, Fujian Branch, Nan'an National University Science Park, Quanzhou City, China. Tel: 15889795946 4﹑Darkroom testing 4.0 Testing Equipment Test system: ETS shielded darkroom Test environment: temperature 22 °C± 3 °C, humidity 50% ± 15% Test equipment: when testing passive data, use network analyzer Agilent E5071B When testing active data, use a comprehensive tester Agilent 8960 8820C 4.1 Test method description and diagram: The testing system consists of a darkroom, turntable, source antenna system, testing instruments, and control computer. The testing computer is the controller of the entire system. During testing, the testing computer controls the turntable to rotate to a certain angle, and then controls the instrument to perform spatial attenuation testing. After collecting the raw data, the data is compensated and corrected, and finally the test data is obtained. The schematic diagram is as follows: 4.2 Antenna Test Report (BT efficiency)： Freq Effi Effi Gain Gain (MHz) (%%) (dB) (dBi) (dBd) 2400 38.83 -0.41 -0.47 -2.62 2420 40.12 -0.39 -0.23 -2.38 2440 40.33 -0.39 -0.35 -2.5 2460 39.39 -0.40 -0.15 -2.3 2480 38.52 -0.41 0 -2.15 2500 36.55 -0.43 -0.07 -2.22 根 通 通 信 技 术 有 限 公 司 Gentong Communication Technology Co.,Ltd Address: 5th Floor, Building 7, Fujian Branch, Nan'an National University Science Park, Quanzhou City, China. Tel: 15889795946 5、BT Antenna Photo 9.5*4.3MM

Page 1 of 69 FCC Test Report Report No.: AGC00319260204FR03 FCC ID : 2ASNSEZ09 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : EZTalk 5 APPLICANT : Shenzhen Retevis Technology Co., Ltd. DATE OF ISSUE : Mar. 12, 2026 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation Of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC00319260204FR03 Page 2 of 69 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 12, 2026 Valid Initial Release Report No.: AGC00319260204FR03 Page 3 of 69 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 7 2.4 Test Methodology ...................................................................................................................................... 7 2.5 Special Accessories .................................................................................................................................. 7 2.6 Equipment Modifications ........................................................................................................................... 7 2.7 Antenna Requirement................................................................................................................................ 7 3. Test Environment ............................................................................................................................................ 8 3.1 Address of the Test Laboratory ................................................................................................................. 8 3.2 Test Facility ................................................................................................................................................ 8 3.3 Environmental Conditions ......................................................................................................................... 9 3.4 Measurement Uncertainty ......................................................................................................................... 9 3.5 List of Equipment Use ............................................................................................................................. 10 4.System Test Configuration ............................................................................................................................ 12 4.1 EUT Configuration ................................................................................................................................... 12 4.2 EUT Exercise ........................................................................................................................................... 12 4.3 Configuration of Tested System .............................................................................................................. 12 4.4 Equipment Used In Tested System ........................................................................................................ 13 4.5 Summary of Test Results ........................................................................................................................ 14 5. Description of Test Modes ........................................................................................................................... 15 6. Duty Cycle Measurement ............................................................................................................................. 16 7. RF O…

Text truncated - open the document above for the full version.