2ASNSEZT0Walkie Talkie

EZTalk 80 USER’S MANUAL 正面 背面 Assembly Oveiew (Order: Front cover → Back cover; Speaker → Motherboard; Test before closing the case) 2 Place the Front Cover Lay the front cover h at with the mesh side against the table, ready to “welcome” the components. 1 Preparation Lay out all pas a–m. Work with an adult for safety and extra fun. 3 Install the PTT Button Inse the PTT button cap i from inside into the button slot. Make sure the small hole is on the left and the big hole is on the right. Press it—if it bounces back smoothly, it’s correct. 4 Install Speaker and Fixing Ring Place the speaker d into the large round slot with wires facing upward toward the antenna.Use the xing ring c to press the speaker down, securing all four corners tightly. 5 Install Circuit Board Gently place the circuit board j into the front cover with the spring antenna facing up towards the antenna slot. Ensure the board edges t inside the bracket. Note: The small spring on top of the board is the antenna—carefully guide it through the hole in the front cover. 6 Connect the Speaker Pass the speaker’s red and black wires through the hole on the motherboard.Then align the white plug at the top with the SPK socket on the circuit board, keep it not skewed, and plug it in. 7 Place the Front Cover Place antenna cover a into the long upper slot. Secure with the U-shaped clip b until you hear a “click.” 8 Secure the Circuit Board Use screws e to x the board on the posts (four corners + center). Remember to tighten it. 10 Install Batteries & Battery Cove Be extra careful here: Ensure the power switch is at the top right (Power OFF). Open the batte cover, inse 3 × AA batteries (check polarity marks, do not reverse). Close the batte cover and secure with screws f. Note: Remove the batte if the device will not in use for a long time. A Little Sto About Walkie-Talkies Once upon a time, people could only send messages by writing letters or shouting loudly. Then, scientists discovered an "invisible magic wave"—Radio Waves! These waves could travel quickly through the air and car sound over long distances. In the 20th centu, people invented walkie-talkies. The earliest walkie-talkies were huge, like a brick, and could only be used by the milita or police. As technology improved, walkie-talkies became smaller and more advanced, and soon ordina people could use them to chat with friends. Today, you can even build your own walkie-talkie and use it to communicate with your buddies! How cool is that? How Do Walkie-Talkies Work? A walkie-talkie is like a "magic bridge." 1. When you speak: Your voice is captured by a small microphone and turned into an electrical signal. 2. Electrical signal transformation: This signal rides on an "invisible fast train"—radio waves—that quickly travels through the air. 3. Your friend's walkie-talkie receives it: The other walkie-talkie acts like a catcher, grabbing the incoming radio waves and turning them back into sound. 4. And then you can chat! Isn't it amazing? These invisible and untouchable “waves” can actually car sound ying back and foh! A Brief Guide to Walkie-Talkies A Interesting Trivia A walkie-talkie is like a superhero's "instant megaphone”—no need for SIM cards or internet! Radio waves travel incredibly fast, almost as fast as light! But here’s a little secret about walkie-talkies: Only one person can speak at a time; the other must remain silent, or else their voices will clash. may result in accidental contact of positive/negative poles). 5."Modication by feel" is prohibited: Do not replace the original kit pas (such as mismatched batteries, wires, etc.), or subtract/add components (such as leaving out insulating pads). This may damage circuit stability and cause overheating or leakage risks. 6.Guide children to recognize positive/negative poles (“+/-” signs on both circuit board and batte). Wrong installation can burn the circuit board. 7.Remind children not to put small pas in their mouth throughout assembly: especially screws and small buttons. If the child tends to bite objects, they may wear child gloves during assembly (to avoid accidental picking up and placing). 8.Handle metal pas carefully: Circuit board pins or batte electrodes may scratch. If burrs are present, parents should use sandpaper to gently smooth them out before handing pas to children. Batte Precautions ● Turn o the walkie-talkie before replacing the batte. Install correctly according to the “+/-” polarity marks in the compament. Do not install in reverse. ● After installation, secure the batte cover with screws to prevent children from accidentally opening the batte compament to access the batteries during use. ● Replace the batte immediately if you nd the batte shell bulging, deformation, leakage, electrode rusting, or if transmission/reception becomes unstable during use. Dispose of used batteries properly. ● If the walkie-talkie will not be used for more than 1 month, remove the batte to prevent leakage from damaging the circuit. ● Do not disassemble the batte compament. Do not touch the batte terminals with metal objects (such as keys or coins) to avoid sho circuits. WARNING! Please assemble under adult supeision. Product List – Pas Identication (From left to right, top row → bottom row) a. Transparent Strip Plastic--Antenna Housing Decorative Pas —— puts a "coat" on the antenna b. Small white U-shaped clip--Fixed antenna—— holds the antenna in place so it won’t move around. c. Round white xing ring--Fixed speakers —— secures the speaker and keeps it “standing rm” d. Speaker with red and black wires--Sound output —— Responsible for “talking” e. Small screws (PB2×6, 5mm)--Fixed circuit—— secure the circuit board, giving it a “home” (4 pcs + 1 center screw) f. Screws (PB2×10, 4mm)-- Fixed housing—— secure the housing, fastening the front and back covers together g. Screws (M2×7, 1mm) --Fixed batte cover——secure the batte cover, keeping the batte from falling out …

Text truncated - open the document above for the full version.

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2ASNSEZT0 EZTalk 80 We, Applicant Company Name: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Phone: +86-755-23481953 certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. This includes the cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. or any of ist successors and assignees. We certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2026-03-18 Signature Date Name / Title: Dongfang Shen / Manager Company: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Phone: +86-755-23481953 Fax: N/A E-Mail: [email protected]

Due Diligence Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern FCC ID Model name 2ASNSEZT0 EZTalk 80 Pursuant to KDB 986446 D01 Covered Equipment Guidance the evaluation of the product above shows compliance for the following reasons: Compliance Evaluation process Results Inherent compliance The chipset(s) used is not capable of running the cybersecurity and/or anti-virus software Compliance The memory used does not allow the running the cybersecurity and/or anti-virus software Compliance The storage capacity does not allow the running the cybersecurity and/or anti-virus software Compliance The operating system used is not capable of running the cybersecurity and/or anti-virus software Compliance No inherent compliance Based on software bill of material Based on scan for running software on the device Based on filesystem scan for cybersecurity and/or anti-virus software The equipment for which authorization is sought complies with the rules and fulfils the requirements as detailed in the above mentioned KDB. Evaluation performed by Company Name: Shenzhen LCS Compliance Testing Laboratory Ltd. Contact Name: Martion Lee Address: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Phone: +86-755-82591330 Email: [email protected] Signature: Date: 2026-03-12

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2ASNSEZT0 EZTalk 80 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are: • the Operational Description • the Block Diagram • the Schematics • the Part List • the Tune up Information The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2026-03-18 Signature Date Name / Title: Dongfang Shen / Manager Company: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Phone: +86-755-23481953 Fax: N/A E-Mail: [email protected]

Page 1 of 4 Report No.: STS2601258 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Page 2 of 4 Report No.: STS2601258 Photo 3 Photo 4 Page 3 of 4 Report No.: STS2601258 Photo 5 Photo 6 Page 4 of 4 Report No.: STS2601258 Photo 7

LABELANDLOCATION (Size:L30mmxW25mm) LabelLocation

Page 1 of 3 Report No.: STS2601258 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Antenna Page 2 of 3 Report No.: STS2601258 Photo 3 Photo 4 Page 3 of 3 Report No.: STS2601258 Photo 5 Photo 6

TEST REPORT For SAR Report No......................................... : CHTW26035001R1 Project No ........................................ : SHT2603089101W FCC ID ............................................. : 2ASNSEZT0 Applicant’s name ............................. : Shenzhen Retevis Technology Co., Ltd. Address ............................................ : 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Product Name .................................. : Walkie Talkie Trade Mark....................................... : RETEVIS Model No.......................................... : EZTalk 80 Listed Model(s) ................................ : - Standard .......................................... : FCC 47 CFR Part2.1093 ANSI/IEEE Std C95.1-1992 IEEE Std 1528-2013 Date of receipt of test sample..........: 2026/1/21 Date of testing.............................: 2026/1/26, 2026/3/27 Date of issue...............................: 2026/3/30 Result ................... ........................: PASS Compiled by (Position+Printed name+Signature) : File administrator Caspar Chen Supervised by (Position+Printed name+Signature) : Project Engineer Xiaodong Zhao Approved by (Position+Printed name+Signature) : RF Manager Xu Yang Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address ............................................ : Building 7, Baiwang Idea Factory, No.1051, Songbai Road, Yangguang Community, Xili Subdistrict, Nanshan District, Shenzhen, Guangdong, China Test Report Form No. ........................ : R0066 Test Report Form(s) Originator ......... : Shenzhen Huatongwei International Inspection Co., Ltd. Master TRF ........................................ : Dated 2025-07 Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.The test report merely correspond to the test sample.The authenticity of this Test Report and its contents can be verified by contacting the Laboratory, responsible for this Test Report. Report No.: CHTW26035001R1 Page 2 of 29 Contents 1. Statement of Compliance 3 2. Test Standards and Report version 4 2.1. Test Standards 4 2.2. Report version 4 3. Summary 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 5 3.4. Test frequency list 6 3.5. Testing Laboratory Information 6 3.6. Environmental conditions 6 4. Equipments Used during the Test 7 5. Measurement Uncertainty 8 6. SAR Measurements System Configuration 9 6.1. SAR Measurement Set-up 9 6.2. DASY5 E-field Probe System 10 6.3. Phantoms 11 6.4. Device Holder 11 7. SAR Test Procedure 12 7.1. Scanning Procedure 12 7.2. Data Storage and Evaluation 14 8. Position of the wireless device in relation to the phantom 16 8.1. Front-of-face 16 8.2. Body Position 16 9. Dielectric Property Measurements & System Check 17 9.1. Tissue Dielectric Parameters 17 9.2. SAR System Validation 18 9.3. System Check 18 10. SAR Exposure Limits 22 11. Antenna Location 23 12. Radiated Power Measurement Results and Tune-up 24 13. SAR Measurement Results 25 14. Test Setup Photos 26 15. External Photos of the EUT 28 Report No.: CHTW26035001R1 Page 3 of 29 1. Statement of Compliance Maximum Reported SAR (W/kg @1g) RF Exposure Conditions FRS Front-of-face(Dist.= 25mm) 0.145 Body-worn(Dist.= 0mm) 0.311 Note: 1. This device is in compliance with Specific Absorption Rate (SAR) for general population/uncontrolled exposure limits (1.6 W/kg@1g) specified in FCC 47 CFR part 2 (2.1093) and IEEE Std C95.1, 2. This device had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and FCC KDB publications. Report No.: CHTW26035001R1 Page 4 of 29 2. Test Standards and Report version 2.1. Test Standards The tests were performed according to following standards: FCC 47 Part 2.1093: Radiofrequency Radiation Exposure Evaluation:Portable Devices ANSI/IEEE C95.1-1992: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE Std 1528-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. FCC published RF exposure KDB procedures: KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 865664 D02 RF Exposure Reporting v01r02: RF Exposure Compliance Reporting and Documentation Considerations KDB 447498 D04 Interim General RF Exposure Guidance v01: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies TCB workshop: April, 2019; Page 19, Tissue Simulating Liquids (TSL) 2.2. Report version Revision No. Date of issue Description N/A 2026-03-02 Original R1 2026-03-30 Update the test interval distance for body worn to 0mm and conduct a new test. Report No.: CHTW26035001R1 Page 5 of 29 3. Summary 3.1. Client Information Applicant: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Manufacturer: Shenzhen Retevis Technology Co., Ltd. Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China 3.2. Product Description Main unit Name of EUT: Walkie Talkie Trade Mark: RETEVIS Model No.: EZTalk 80 Listed Model(s): - Power supply: DC 4.5V Hardware version: V01 Software version: …

Text truncated - open the document above for the full version.

Appendix E: DAE and Probe Calibration Certificate 6 of 12 Appendix E: DAE and Probe Calibration Certificate 7 of 12 Appendix E: DAE and Probe Calibration Certificate 8 of 12 Appendix E: DAE and Probe Calibration Certificate 9 of 12 Appendix E: DAE and Probe Calibration Certificate 10 of 12 Appendix E: DAE and Probe Calibration Certificate 11 of 12 Appendix E: DAE and Probe Calibration Certificate 12 of 12 Appendix F: Dipole Calibration Certificate 1 of 8 1.1. D450V3 Dipole Calibration Certificate Appendix F: Dipole Calibration Certificate 2 of 8 Appendix F: Dipole Calibration Certificate 3 of 8 Appendix F: Dipole Calibration Certificate 4 of 8 Appendix F: Dipole Calibration Certificate 5 of 8 Appendix F: Dipole Calibration Certificate 6 of 8 Appendix F: Dipole Calibration Certificate 7 of 8 Extended Dipole Calibrations Referring to KDB865664 D01, if dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Head-450 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2024-01-24 -21.5 58.4 -3.50 2025-01-17 -22.3 3.72 56.3 2.1 -5.19 1.69 2026-01-13 -22.5 4.65 56.2 2.2 -4.96 1.46 The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5ohm of prior calibration. Therefore the verification result should support extended calibration. Impedance Measurement Plot-2025/1/17 Appendix F: Dipole Calibration Certificate 8 of 8 Impedance Measurement Plot-2026/1/13

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2601258W01 Issued for Shenzhen Retevis Technology Co., Ltd. 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Product Name: Walkie Talkie Brand Name: RETEVIS Model Name: EZTalk 80 Series Model(s): N/A FCC ID: 2ASNSEZT0 Test Standard: FCC Part 95 Page 2 of 32 Report No.: STS2601258W01 TEST REPORT Applicant’s Name ..................... : Shenzhen Retevis Technology Co., Ltd. Address ...................................... : 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Manufacturer's Name ............... : Shenzhen Retevis Technology Co., Ltd. Address ...................................... : 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China Product Description Product Name ............................ : Walkie Talkie Brand Name ............................. : RETEVIS Model Name ............................... : EZTalk 80 Series Model(s) .......................... : N/A Test Standards .......................... : FCC Part 95 Test Procedure ........................... : TIA 603-E This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test .......................................... : Date of receipt of test item .................... : 25 Jan. 2026 Date of performance of tests ................ : 25 Jan. 2026~12 Feb. 2026 Date of Issue ........................................ : 12 Feb. 2026 Test Result ........................................... : Pass Testing Engineer : (Lenon Hou) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 32 Report No.: STS2601258W01 Table of Contents 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 10 2.5 EQUIPMENTS LIST 11 3. FIELD STRENGTHS AND RADIATED SPURIOUS EMISSION 12 3.1 RADIATED EMISSION LIMITS 12 3.2 TEST PROCEDURE 13 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULT 15 4. SPURIOUS EMISSION ON ANTENNA PORT 16 4.1 LIMIT 16 4.2 TEST PROCEDURE 16 4.3 TEST SETUP 16 4.4 EUT OPERATION CONDITIONS 16 4.5 TEST RESULT 17 5. BANDWIDTH TEST 18 5.1 LIMIT 18 5.2 TEST PROCEDURE 18 5.3 TEST SETUP 18 5.4 EUT OPERATION CONDITIONS 18 5.5 TEST RESULTS 19 6. TRANSMITTER OUTPUT POWER AND EFFECTIVE RADIATED POWER (E.R.P) 20 6.1 LIMIT 20 6.2 TEST PROCEDURE 20 6.3 TEST SETUP 21 6.4 TEST RESULTS 21 7. EMISSION MASK 22 7.1 LIMIT 22 Page 4 of 32 Report No.: STS2601258W01 Table of Contents 7.2 TEST PROCEDURE 22 7.3 TEST SETUP 22 7.4 EUT OPERATION CONDITIONS 22 7.5 TEST RESULT 23 8. FREQUENCY STABILITY 24 8.1 LIMIT 24 8.2 TEST PROCEDURE 24 8.3 TEST SETUP 24 8.4 EUT OPERATION CONDITIONS 24 8.5 TEST RESULT 25 9. MODULATION LIMIT 26 9.1 LIMIT 26 9.2 TEST PROCEDURE 26 9.3 TEST SETUP 26 9.4 TEST RESULT 27 10. AUDIO LOW PASS FILTER RESPONSE 28 10.1 LIMIT 28 10.2 TEST PROCEDURE 28 10.3 TEST SETUP 28 10.4 TEST RESULT 29 11. AUDIO FREQUENCY RESPONSE 30 11.1 LIMIT 30 11.2 TEST PROCEDURE 30 11.3 TEST SETUP 30 11.4 TEST RESULT 31 APPENDIX 1- PHOTOS OF TEST SETUP 32 Page 5 of 32 Report No.: STS2601258W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 12 Feb. 2026 STS2601258W01 ALL Initial Issue Page 6 of 32 Report No.: STS2601258W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part 95 Standard Section Test Item Judgment Remark FCC Part 95.567 Transmitter Output Power and Effective Radiated Power (e.r.p) PASS -- FCC Part 95.573 Authorized Bandwidth PASS -- FCC Part 95.579 Emission Mask PASS -- FCC Part 95.579 Transmitter Radiated Spurious Emission PASS -- FCC Part 95.579 Spurious Emission On Antenna Port PASS -- FCC Part 95.565 Frequency Stability PASS -- FCC Part 95.575 Audio Low Pass Filter Response PASS -- FCC Part 95.575 Audio Frequency Response PASS -- FCC Part 95.575 Modulation Requirements PASS -- NOTE: (1) “N/A” denotes test is not applicable in this Test Report. (2) All tests are according to TIA 603-E. Page 7 of 32 Report No.: STS2601258W01 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. :101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.87dB 2 Unwanted Emissions, conducted ±2.895dB 3 All emissions, radiated 9K-30MHz ±3.80dB 4 All emissions, radiated 30M-1GHz ±4.09dB 5 All emissions, radiated 1G-6GHz ±4.92dB 6 All emissions, radiated>6G ±5.49dB Page 8 of 32 Report No.: STS2601258W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Walkie Talkie Brand Name RETEVIS Model Name EZTalk 80 Series Model(s) N/A Model Difference N/A Operation Frequency Range: 467.5625MHz Channel Separation 12.5KHz Modulation Type FM Emission ty…

Text truncated - open the document above for the full version.

Report No.: CHTW26035001R1 Page 26 of 29 14. Test Setup Photos Liquid depth in the flat Phantom Front-of-face(25mm) Body-worn Front(0mm) Report No.: CHTW26035001R1 Page 27 of 29 Body-worn Back(0mm)

Page 1 of 2 FCC ID: 2ASNSEZT0 Setup photo RE (Below 1GHz) RE (Above 1GHz) Page 2 of 2 FCC ID: 2ASNSEZT0 RF Conduction