2ASPN-ID300UWB Tag

Confidential Do not copy without permission 1 GEO TAG ID300 SPECIFICATION Geoplan Co.,Ltd. GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 2 Overview  ID300 tag is a UWB device developed by Geoplan, which uses UWB standard compatible SR040 chip.  ID300 tag is designed primarily to determine real-time location and can be used in various environments, including offices, hospitals, factories, and etc.  The tag can replace ID card holders used by staff as it has card slot to hold employee cards.  The tag can replace regular emergency buttons in the building as it has an emergency button on the back, with alarm sound and buzzer Design GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 3 Specification ID300 System Specification Feature Specification Radio Transceiver UWB IEEE 802.15.4/4z (NXP SR040), 8GHz BLE BLE 5.1, (QPG6100), 2.4GHz Interface Support Button 1 button: Activate / Alarm / Battery check / Reset Acceleration Sensor Motion detection: BMA400 LED 1ea: 3color Buzzer Sound pressure level: Piezo MIN 70dB Physical Characteristics Operating Temp Temperature: -20 ~ +60 °C/Humidity: 5 ~ 90%RH Storage Temp Temperature: -40 ~ +70 °C/Humidity: 5 ~ 90%RH Power supply Coin batteries: CR2032 x 2ea IP Classification IP 54 Tag Material Polycarbonate Protective Film 0.24mm thick card protective film as a part of a tag Battery Door Attached with 4ea metal screws GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 4 ID300 Cleaning Specification Avoid to use Use with caution Safe to use acetone cyclohexanone 0.5% accelerated hydrogen peroxide acrylonitrile diesel ammonium chloride ammonia formic acid antimony trichloride amyl gasoline saturated aqueous solution of borax acetate glycerin butane benzene kerosene calcium hypochlorite bromine jet fuel/aviation fuel potassium dichromate butyl concentrated peracetic acid/peroxide carbon dioxide acetate isoamyl alcohol carbon monoxide sodium terpineol 10% hydrogen cyanide hydrosulfite copper sulfate chloroform 95% ethanol dimethylformamide ethylene glycol concentrated hydrochloric acid 10% formaldehyde iodine 20% salt/acid methanol 5% hydrofluoric acid butanol hydrogen styrene tetrafluoroethylene methane toluene oxygen concentrated sulfuric acid ozone xylene solvent GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 5 Dimensions LED Scenario Operation Status LED LED Description Red Alarm Active/Battery Check Blue Factory Reset/Deep Sleep Green Battery Check GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 6 Button Scenario 1. Alarm Activate Press the button for 3 seconds to activate an alarm. A beep sound and Red LED blinks indicate that the Alarm is active. 2. Alarm Cancel Press the button twice quickly during activation to cancel the alarm. 3. Battery Check Press the button for 6 seconds: Green blink: Battery life is over 20% (Buzzer sound: Mi-40%, Sol-60%, Do-80%) Red blink: Battery life is under 20% (Buzzer sound: 5 degree) 4. Factory Reset/Deep Sleep Press the button for more than 10 seconds to trigger the device to enter deep sleep mode. Note: Location data is visible for 5 seconds after a factory reset. GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 7 FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. UWB devices operating under the provisions of this section must be hand held, i.e., they are relatively small devices that are primarily hand held while being operated and do not employ a fixed infrastructure. (1) A UWB device operating under the provisions of this section shall transmit only when it is sending information to an associated receiver. The UWB intentional radiator shall cease transmission within 10 seconds unless it receives an acknowledgement from the associated receiver that its transmission is being GEO TAG ID300 SPECIFICATIONS V 2.0 Confidential Do not copy without permission 8 received. An acknowledgment of reception must continue to be received by the UWB intentional radiator at least every 10 seconds or the UWB device must cease transmitting. (2) The use of antennas mounted on outdoor structures, e.g., antennas mounted on the outside of a building or on a telephone pole, or any fixed outdoors infrastructure is prohibited. Antennas may be mounted only on the hand held UWB device. (3) UWB devices operating under the provisions of this section may operate indoors or outdoors. RF Exposure This portable transmitter with…

Text truncated - open the document above for the full version.

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-24-2025 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2ASPN-ID300 Geoplan Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Geopaln Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Young Ha Shin / Dept. Manager Address: 622, Geumjeong SKV1, 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, South Korea E-mail: [email protected] Tel/Fax: +82-31-689-5541 Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-24-2025 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2ASPN-ID300 Geoplan Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Young Ha Shin / Dept. Manager Address: 622, Geumjeong SKV1, 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, South Korea E-mail: [email protected] Tel/Fax: +82-31-689-5541

142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea Tel/Fax: 031-689-5541 / 031-696-9960 UNITED STATES DESIGNATED AGENT LETTER Date: 2025-07-24 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Applicant U.S. designated agent Company Name: Geoplan Co., Ltd. Company Name: Geoplan Technology Inc Grantee Code: 2ASPN Contact Name: JiSung Kim Contact Name: Youngha Shin Address: 3003 N, 1 st Street #173, Address: 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea City/Province/Zip: San Jose, CA 95134 5519982 Applicant FRN 0028313856 Agent FRN: - City/Province/Zip: 14118 Telephone: (408) 519-5773 Telephone: +82-031-689-5541 Fax: (408) 432-5020 Fax: Email: [email protected] Email: [email protected] *The agent for service of process does no other business with the FCC and does not have an FRN Applicable Grantee Code: 2ASPN ATTN: Director of Certification: We, Geoplan Co., Ltd. understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, Geoplan Technology Inc. acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Youngha Shin Name (Printed): JiSung Kim Title: H/W Development Team manager Title: CEO Signature: Signature:

Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request regarding application for certification of FCC ID: 2ASPN-ID300 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File name Block diagram Circuit Description Operational Description Part list CONF APPENDIX_ID300_BLK CONF APPENDIX_ID300_SCH CONF APPENDIX_ID300_Operation Description CONF APPENDIX_ID300_BOM The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 and 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Date: 2025. 07. 23 Young Ha Shin / Dept. Manager Address: 622, Geumjeong SKV1, 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, South Korea Tel/Fax: +82-31-689-5541

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 2025. 07. 23 SUBJECT: FCC Application for FCC ID: 2ASPN-ID300 To Whom It May Concern: We, the undersigned, hereby authorize Yunkyoung-Kwak at Bureau Veritas CPS Korea Tech Limited on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Yunkyoung-Kwak at Bureau Veritas CPS Korea Tech Limited on our behalf shall have the same effect as acts of our own. Sincerely, Young Ha Shin / Dept. Manager Address: 622, Geumjeong SKV1, 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, South Korea Tel/Fax: +82-31-689-5541

Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 1 / 4 Appendix 2. Photographs of EUT [External View] [Front] [Rear] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 2 / 4 [Top] [Bottom] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 3 / 4 [Left] [Right] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 4 / 4 [Antenna] BLANK

Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 1 / 1 Appendix 4. Sample Label & Location Label Information The following is a sample copy of the label that will be placed on back side of the product. The FCC ID is marked in the product label and below information is visible printed on the label. Label location The label shown above shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase. The label is located here.

Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 1 / 5 Appendix 3. Photographs of EUT [Internal View] [Inside] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 2 / 5 [PCB Board_Top] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 3 / 5 [PCB Board_Bottom] UWB Antenna BLE Antenna B ureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 4 / 5 [Chip Photo] Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Page: 5 / 5 [Battery]

RF Exposure Product: UWB Tag Applicant: Geoplan Co., Ltd. Model: ID300 Address: 622, Geumjeong SKV1, 142, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, South Korea FCC ID: 2ASPN-ID300 KDB 447498 D01 General RF Exposure Guidance v06, section 4.3.1(a) Standalone SAR test exclusion threshold is applied; a) For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR,  where f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison  The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The equation and threshold in 4.3.1 must be applied to determine SAR test exclusion. Appendix A. SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤50 mm ▣ BLE Frequency (GHz) Max. output power Evaluation Distance (mm) SAR test exclusion Threshold Limit (dBm) (mW) 2.402-2.480 -5.98 0.252 5 0.000 22 3.0 - Freq: 2 402 MHz Max. power : -5.98 dBm (0.252 mW) Min. Test separation distance : 5 mm SAR exclusion threshold: [0.252/5] x [√2.402] = 0.078 ▣ UWB Frequency (GHz) Max. EIRP Evaluation Distance (mm) SAR test exclusion Threshold Limit (dBuV/m) (dBm) (mW) 6.489 6 81.69 -23.05 0.005 5 0.003 3.0 7.987 2 77.10 -27.64 0.002 5 0.001 3.0 - Freq: 6 489.6 MHz Max. power : -23.05 dBm (0.005 mW) Min. Test separation distance : 5 mm SAR exclusion threshold: [0.005/5] x [√6.489 6] = 0.003 - Freq: 7 987.2 MHz Max. power : -27.64 dBm (0.002 mW) Min. Test separation distance : 5 mm SAR exclusion threshold: [0.002/5] x [√7.987 2] = 0.001 Results: Compliant UWB and BLE radios do not operate simultaneously.

Report No.: BVT-RH-FCR-250004 BVTRF-FCR-RFT 2 / 26 Revision History of test report Date Report No. Revision Histoty 2025.10.15 BVT-RH-FCR-250004 Initial issue Report No.: BVT-RH-FCR-250004 BVTRF-FCR-RFT 3 / 26 Contents 1. INFORMATION OF TESTING LABORATORY ......................................................................................................... 4 2 SUMMARY OF TEST RESULTS ............................................................................................................................ 5 2.1 DECISION RULES FOR STATEMENT OF CONFORMITY ........................................................................................................................ 6 2.2 MEASUREMENT UNCERTAINTY ................................................................................................................................................................ 6 3 GENERAL INFORMATION ..................................................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................................................................................ 7 3.2 TESTED SAMPLE AND TESTED COMPANION DEVICE INFORMATION ................................................................................................ 7 3.3 DESCRIPTION OF TEST MODE .................................................................................................................................................................. 8 3.4 INSTRUMENT CALIBRATION ........................................................................................................................................................... 8 3.5 EUT CONFIGURATION ......................................................................................................................................................................... 8 3.6 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................................................................................ 8 3.7 TEST EQUIPMENT ........................................................................................................................................................................................ 9 3.8 TEST SOFTWARE ......................................................................................................................................................................................... 9 4 TEST RESULTS .................................................................................................................................................... 10 4.1 MAX. CONDUCTED OUTPUT POWER .................................................................................................................................................... 10 4.2 POWER SPECTRAL DENSITY .................................................................................................................................................................. 12 4.3 6 DB SPECTRUM BANDWIDTH ............................................................................................................................................................... 14 4.4 BAND-EDGE COMPLIANCE OF RF CONDUCTED EMISSIONS ......................................................................................................... 16 4.5 SPURIOUS RF RADIATED EMISSIONS.................................................................................................................................................. 19 4.6 ANTENNA REQUIREMENT ........................................................................................................................................................................ 25 4.7 AC POWER CONDUCTED EMISSIONS .................................................................................................................................................. 26 Report No.: BVT-RH-FCR-250004 BVTRF-FCR-RFT 4 / 26 1. Information of Testing Laboratory Legal Name and address Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, 18326, Republic of Korea Website: http://www.bvcpskoreatech.co.kr Registration information - KOLAS No.: KT232 - RRA No.: KR0041 - A2LA No.: 4068.02, 4068.03 - FCC Designation No.: KR0041 - ISED Designation No.: KR0041 - VCCI Membership No.: 2005 Test location and address Hwaseong (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, 18326, Republic of Korea Te l : 8 2-31-222-4251 Anyang Heungan-daero 49, Dongan-gu, Anyang-si, Gyeonggi-do, 14119, Republic of Korea Tel: +82-31-689-4110, Fax: +82-31-689-4120 Report No.: BVT-RH-FCR-250004 BVTRF-FCR-RFT 5 / 26 2 Summary of Test Results The EUT has been tested according to the following specifications Applied Standard : FCC Part 15, Subpart C 15.225 FCC Part Section(s) Test Description Limit Test Condition Test Result Referenc e 15.247(b) Max. Conducted output power <30 dBm Conducted PA SS Section 4.1 15.247(e) Power spectral density <8 dBm/3kHz Conducted PA SS Section 4.2 15.247(a) 6 dB spectrum Bandwidth >0.5 MHz Conducted PA SS Section 4.3 15.247(d) Band-edge Compliance of RF conducted emissions FCC 15.247(d) Conducted PA SS Section 4.4 15.247(d)/ 15.209(a) Spurious RF radiated emissions FCC 15.247(d), 15.209(a) Radiated PA SS Section 4.5 15.203 Antenna requirement FCC 15.203 - PA SS Section 4.6 15.207 AC Conducted emission < FCC 15.207 limits AC Line Conducted N/A Section 4.7 Report No.: BVT-RH-FCR-250004 BVTRF-FCR-RFT 6 / 26 2.1 Decision Rules for Statement of Conformity QUA-52 Decision Rule(QA Document) was applied. Step 1) : Reference Check, Daily Check, Peripheral device Check Step 2) : Re-test Procedure (Repeat the test maximum 3 times, Different Test Engineer) 1) If the original test results are subject to retesting and the judgement is unclear, the retest is carried out. 2…

Text truncated - open the document above for the full version.

2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 1 of 5 *Efficiency based on Johanson's standard evaluation board ±± ±± ±± https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved Want the layout file? Request it at: https://www.johansontechnology.com/ask-a-question High Frequency Ceramic Solutions Part Number 11/5/2018 Avg. Rad Efficiency* Let us help you with the antenna design, optimization, and tuning! 2450AT18B100 2400 - 2500 76% General Specifications Frequency (MHz) -45 to +125°C -45 to +125°C 3000pcs Return Loss (dB) Impedance Input Power Storage Temperature Operating Temperature Reel Quantity 50 Ω 2 Watts max. (CW) Recommended Storage Conditions of unused product on T&R and period. +5 to +35°C Humidity 45~75%RH 18 months max. Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. e.g. 2450AT18B100(E or S)100% Tin Packing Style Evaluation Board 2450AT18B100-EB1SMA (see page 2&3 for details) Bulk (loose) T & R Suffix = E or S Suffix = E P/N Suffix Mechanical Dimensions In L 0.1260.0083.200.2 W 0.0630.0081.600.2 T 0.0511.30 +0.1/-0.2+.004/-.008 a 0.0200.0080.500.2 Terminal Configuration Function FEED NC No. 1 2 mm e.g. 2450AT18B100E e.g. 2450AT18B100SSuffix = S Part Number Explanation Peak Gain (dBi typ.) Average Gain (dBi typ.) 0.5 -0.5 9.5 min. ① ② L W a T 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 2 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Evaluation Board Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. To order a pre‐tuned 50Ω EVB with a female SMA connector click here: https://www.johansontechnology.com/request‐a‐sample Reference p/n: 2450AT18B100‐EB1SMA GND NO GND Units in mm ) ) 13.5 6.5 39.5 6.5 50Feed Line Antenna 4 ) Matching Component JTI P/Ns: L-14C2N7JV4 L-14C2N2JV4 * 2.6 4.2 1.6 1.9 0.4 2.7nH 1.2pF 3.3nH JTI P/N for Matching Circuit: Capacitor (1.2pF): 500R07S1R2BV4T Inductor (2.7nH): L-07C2N7SV6T Inductor (3.3nH): L-07C3N3SV6T *Line width should be designed to provied 50Ω impedance 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 3 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Typical Electrical Performance (T=25°C) Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Would you like the antenna layout? Have antenna tuning issues? Please contact us if you have any questions regarding the implementation of this antenna in your PCB's layout. We'll be happy to guide you to maximize the antenna's performance. Contact our applications engineers at: https://www.johansontechnology.com/ask‐a‐question 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 4 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Antenna Performance Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. θ +Z (θ= 0°) +Y (θ= 90°) -Y -Z Typical 2D radiation patterns @ 2.44GHz YZ‐plane XZ‐plane XY‐plane Z Y Z X X Y φ +X (φ= 0°) -X +Y (φ= 90°) -Y θ +Z (θ= 0°) +X (θ= 90°) -X -Z 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 5 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved https://www.johansontechnology.com/rohs-compliance Need help designing the antenna in? Use our antenna design services! https://www.johansontechnology.com/ipc-antenna-services We provide 2 free layout reviews and if you need us to tune and characterize the antenna on your product (inside our anechoic chamber) we can do that too. Small lab fee may apply. High Frequency Ceramic Solutions Antenna tuning, optimization, and validation services: For more antennas and to download measured S-parameters, go to: 11/5/2018 Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. RoHS Compliance Soldering Information For layout review contact our Applications Team at: MSL Info Packaging information https://www.johansontechnology.com/ipc-antenna-services https://www.johansontechnology.com/antennas https://www.johansontechnology.com/ipcsoldering-profile https://www.johansontechnology.com/msl-rating https://www.johansontechnology.com/tape-reel-packaging https://www.johansontechnology.com/ask-a-question 7GHz Mini UWB Antenna, AEC-Q200 QualifiedP/N 7000AT18A1600E-AEC Detail Specification: Page 1 of 5 ±± ±± + 0.1 / -0.2 ±± https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 2.0 2020 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions Part Number 2/18/2020 Avg. Rad Efficiency Let us help you with the antenna design, optimization, and tuning! 7000AT18A1600E-AEC 6.2 - 8.24 92% General Specifications Frequency (GHz) -40 to +105°C 3,000 Return Loss (dB) Impedance Input Power Operating Temperature Reel Quantity 50 Ω 3 Watts max. (CW) +5 to +3…

Text truncated - open the document above for the full version.

Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Pa g e: 1 / 3 Appendix 1. Photographs of test setup Radiated RF measurement (Below 1 GHz) Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Pa g e: 2 / 3 Radiated RF measurement (Above 1 GHz_1m) Bureau Veritas CPS Korea Tech Limited (Annyeong-dong) 26, 28, 30, Seja-ro 406beon-gil, Hwaseong-si, Gyeonggi-do, Republic of Korea Tel:031-222-4251, Fax: Pa g e: 3 / 3 Radiated RF measurement (Above 1 GHz_3m)