2ASRT-NPX760Digital Projector

Screeneo Innovation SA Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 [August 19, 2026] U.S. Agent Designation [Screeneo Innovation SA] acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought FCC ID: 2ASRT-NPX760 Name and company of U.S. agent: [GLOCERTS TECHNOLOGY INC] Physical U.S. address of agent: [19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507] FRN of U.S. agent: [0036339737] Email address of U.S. agent: [[email protected]] Telephone of U.S.agent: (626) 588-8039 [GLOCERTS TECHNOLOGY INC] acknowledges their obligation to accept service of process on behalf of [Screeneo Innovation SA]. [Screeneo Innovation SA] with the FRN [0028331841] accepts its obligation to maintain an agent for service of process in the United States for no less than 1 year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission- related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Signature [Dan Mamane] [Huiying Fan] [CEO & President] [Director] [Screeneo Innovation SA] [GLOCERTS TECHNOLOGY INC]

Screeneo Innovation SA 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Product Name: Digital Projector FCC ID: 2ASRT-NPX760 Model(s): NeoPix 760 Smart, NPX760 2.911(d)(5)(i) Equipment Type We, [Screeneo Innovation SA] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Dan Mamane Date: August 19, 2026 Title and Company name: CEO & President / Screeneo Innovation SA NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Screeneo Innovation SA 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Product Name: Digital Projector FCC ID: 2ASRT-NPX760 Model(s): NeoPix 760 Smart, NPX760 2.911(d)(5)(ii) Applicant filing We, [Screeneo Innovation SA] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Dan Mamane Date: August 19, 2026 Title and Company name: CEO & President / Screeneo Innovation SA NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Screeneo Innovation SA Agent Authorization Company: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Product Name: Digital Projector Model Number(s): NeoPix 760 Smart, NPX760 Product Description: Digital Projector We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: August 19, 2026 Name: Dan Mamane Title: CEO & President Company: Screeneo Innovation SA

Screeneo Innovation SA Model Difference Data：August 19, 2026 Product description: Digital Projector Model name: NeoPix 760 Smart, NPX760 Trade Name: PHILIPS FCC ID: 2ASRT-NPX760 All the model are the same circuit and RF module, only the model names are different. Regards Sincerely Client’s signature : Client’s name / title : Dan Mamane（CEO & President） Contact information / address：8A route de Suisse, 1163 Etoy - Switzerland

Screeneo Innovation SA Responsibility Declaration Letter v1.0 Responsibility Declaration Letter Company name: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Product Name: Digital Projector FCC ID: 2ASRT-NPX760 Model(s): NeoPix 760 Smart, NPX760 Model(s) Difference Description: All the model are the same circuit and RF module, only the model names are different. We, [Screeneo Innovation SA], hereby acknowledge that all the product information (including all original, drafted, or modified documents) provided to the TCB either by us or our agent or representative(s) for the purposes of FCC certification will meet FCC regulations and requirements; and that any modifications or changes made as a result of TCB review of the documents will be formally implemented into the manufacturing process and product documentation shipped with equipment. We also confirm that all information provided is legitimate and does not contain any false content such as forgery, fabrication, alteration, tampering and concealment. We assume all economic and legal responsibilities in matters that may arise as a result of disclosure on sample products and associated product documentation provided for product certification that may subsequently be found to be a mis-representation of the final product and accompanying documentation when produced, marketed, or sold in the United States, Canada, or anywhere in the world. Your sincerely, Name: Dan Mamane Date: August 19, 2026 Title and Company name: CEO & President / Screeneo Innovation SA

Screeneo Innovation SA Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 19, 2026 Subject; Request for Confidentiality FCC ID: 2ASRT-NPX760 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description FCC Software Security Requirements for UNII devices Rev 2.1 In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Dan Mamane Title: CEO & President

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 4 Model: NeoPix 760 Smart External Photos Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 4 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 4 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 4

FCC ID LABEL: Label Location:

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 10 Model: NeoPix 760 Smart Internal Photos Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 5 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 6 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 7 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 8 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 9 of 10 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 10 of 10 WIFI ANT1 BT+WIFI ANT2

FCC §15.247 (i), §2.1091 – RF Exposure FCC ID: 2ASRT-NPX760 Applied procedures / limit According to FCC §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Note: ƒ is frequency in MHz * = Power density limit is applicable at frequencies greater than 100 MHz Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz * = Plane-wave equivalent power density MPE PREDICTION Predication of MPE limit at a given distance, Equation from OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna,R=20cm Test Result of RF Exposure Evaluation Modes& Channel Freq. (MHz) Tune up Produce power Maximu m peak output power (dBm) Output power to antenna (mW) Antenna Gain (numeric) Power Density (S) (mW/ cm2) Limit (mW / cm2 ) Result EDR 8DPSK& LCH 9±1 10 10 3.0409 (4.83dBi) 0.0061 1 Pass BLE GFSK& LCH 7±1 8 6.3096 3.0409 (4.83dBi) 0.0038 1 Pass 2.4G WIFI ANT1 802.11b&2 412 18±1 19 79.4328 1.4488 (1.61dBi) 0.0229 1 Pass 2.4G WIFI ANT2 802.11n(H T20)&241 2 14±1 15 31.6228 2.9992 (4.77dBi) 0.0189 1 Pass 5.2G WIFI ANT1 802.11n(H T20)& 5240 15±1 16 39.8107 2.5003 (3.98dBi) 0.0198 1 Pass 5.2G WIFI ANT2 802.11a&5 180 12±1 13 19.9526 2.3823 (3.77dBi) 0.0094 1 Pass 5.8G WIFI ANT1 802.11a&5 825 12±1 13 19.9526 3.8107 (5.81dBi) 0.01513 1 Pass 5.8G WIFI ANT2 802.11n(H T20)& 5825 15±1 16 39.8107 1.8323 (2.63dBi) 0.01452 1 Pass For the Max simultaneous transmission MPE: When a number of sources at different frequencies, and/or broadband sources, contribute to the total exposure, it becomes necessary to weigh each contribution relative to the MPE in accordance with the provisions of Table (A) and Table (B). To comply with the MPE, the fraction of the MPE in terms of E2, H2 (or power density) incurred within each frequency interval should be determined and the sum of all such fractions should not exceed unity. In order to ensure compliance with the MPE for a controlled environment, the sum of the ratios of the power density to the corresponding MPE should not exceed unity. That is BT+WIFI supported simultaneous transmission: BT +2.4GWIFI MIMO: ∑MPE Ratio =0.0061/1+0.028/1=0.0341≤1, So passed. BT+5GWIFI MIMO: ∑MPE Ratio =0.0061/1+0.0251/1=0.0312≤1, So passed. Tech nolo gy Tune up Produce power(dBm) Maximum Tune-up (dBm) Antenna Gain(ANT 1/ANT 2) (numeric) Power Density (S) (mW/ cm2) MPE Limit (mW/ cm2) ∑ MPE Ratio ∑ MPE Ratio Limit Result ANT 1 ANT 2 ANT 1 ANT 2 ANT 1 ANT 2 2.4G WIFI MIM O 14 ±1 14 ±1 15 15 ANT1:1.4488 (1.61dBi) ANT2:2.9992 (4.77dBi) 0.0091 0.0189 1 0.028 1 Pass Tech nolo gy Tune up Produce power(dBm) Maximum Tune-up (dBm) Antenna Gain(ANT 1/ANT 2) (numeric) Power Density (S) (mW/ cm2) MPE Limit (mW/ cm2) ∑ MPE Ratio ∑ MPE Ratio Limit Result ANT 1 ANT 2 ANT 1 ANT 2 ANT 1 ANT 2 5G WIFI MIM O 14 ±1 12 ±1 15 13 ANT1:3.8107 (5.81dBi) ANT2:1.8323 (2.63dBi) 0.0157 0.0094 1 0.0251 1 Pass

Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 59 TEST REPORT Compiled by: Reviewed by: Approved by: Kai Chen Martin Feng Bin Mei / Director Note: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. The tested sample(s) and the sample information are provided by the applicant. The authenticity, accuracy, and completeness of the provided information are the sole responsibility of the applicant. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The result decision rules of our laboratory are based solely on the direct comparison between the actual measured values of test results and the standard limits, without considering the measurement uncertainty.“” indicates the testing items were fulfilled by subcontracted lab. “” indicates the items are not in CNAS accreditation scope. Test item description: Digital Projector FCC ID: 2ASRT-NPX760 Trademark(s): PHILIPS Model/Type reference: NeoPix 760 Smart, NPX760 Applicant’s name: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Manufacturer: Screeneo Innovation SA Address: 8A route de Suisse, 1163 Etoy - Switzerland Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: 1&2/F., Building A, No.26, Xinhe Road, Xinqiao, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: Jul. 19, 2026 Sample tested Date: Jul. 19, 2026 to Aug. 19, 2026 Issue Date: Aug. 19, 2026 Report No.: CTB26071900312RF02 Test Standards FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2020 Test Results PASS Remark: This is Bluetooth radio test report. Shenzhen CTB Testing Technology Co., Ltd. Report No.:CTB26071900312RF02 Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 59 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ................................................................................................................................... 4 2. TEST SUMMARY ....................................................................................................................... 5 3. MEASUREMENT UNCERTAINTY .............................................................................................. 6 4. PRODUCT INFORMATION AND TEST SETUP ......................................................................... 7 4.1 Product Information .......................................................................................................................... 7 4.2 Test Setup Configuration .................................................................................................................. 7 4.3 Support Equipment........................................................................................................................... 7 4.4 Channel List ..................................................................................................................................... 8 4.5 Test Mode ........................................................................................................................................ 8 4.6 Test Environment ............................................................................................................................. 8 5. TEST FACILITY AND TEST INSTRUMENT USED ..................................................................... 9 5.1 Test Facility ...................................................................................................................................... 9 5.2 Test Instrument Used ....................................................................................................................... 9 6. AC POWER LINE CONDUCTED EMISSION ............................................................................. 12 6.1 Block Diagram Of Test Setup ......................................................................................................... 12 6.2 Limit ................................................................................................................................................ 12 6.3 Test procedure ............................................................................................................................... 12 6.4 Test Result ..................................................................................................................................... 14 7. RADIATED SPURIOUS EMISSION .......................................................................................... 16 7.1 Block Diagram Of Test Setup ......................................................................................................... 16 7.2 Limit ................................................................................................................................................ 16 7.3 Test procedure ............................................................................................................................... 17 7.4 Test Result ..................................................................................................................................... 18 8. BAND EDGE AND RF CONDUCTED SPURIOUS EMISSIONS ............................................... 27 8.1 Block Diagram Of Test Setup ......................................................................................................... 27 8.2 Limit ................................................................................................................................................ 27 8.3 Test procedure ............................................................................................................................... 27 8.4 Test Result ............................................................…

Text truncated - open the document above for the full version.

* HPR5G Antenna OTA Passive Testing Passive S-parameter test environment ： Manufacturer:Shenzhen Skyworth Digital Technology Co.,LTD. Address: 14/F Unit A. Skyworth Building, Gaoxin Ave.1s., Nanshan District, Shenzhen, China HPR5G Antnna information: Antenna model number: 5800-2AHPR5G Antenna type: PCB Antenna ANT1 ANT2 * Antenna OTA Passive Testing OTA testing environment： * Antenna OTA Passive Testing S11 return loss parameters for ANT1: 2.4GHz and 5GHz bands Antenna OTA Passive Testing S11 return loss parameters for ANT1: 2.4GHz and 5GHz bands Isolation: S12 or S21 Return Loss Parameters - ANT1 & ANT2: 2.4GHz and 5GHz Bands Antenna OTA Passive Testing * Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Efficiency, Gain: 2.4GHz Band ANT1 Efficiency, Gain: 5GHz Bands ANT1 Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) * Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Efficiency, Gain: 2.4GHz Band ANT2 Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Efficiency, Gain: 5GHz Bands ANT2 * Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Directional pattern: 2.4GHz Band ANT1 E13D E2 H Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Directional pattern: 5GHz Bands ANT1 E13D E2 H * Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Directional pattern: 2.4GHz Band ANT2 E13D E2 H * Antenna OTA Passive Parameter Comparison (Efficiency, Gain, Radiation Pattern) Directional pattern: 2.4GHz Bands ANT2 E13D E2 H

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 2 Model: NeoPix 760 Smart Test Setup Photos of EUT Radiated Emission Below 1G Above 1G Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 2 Conducted emissions RF Conducted