2AT23-M2-MODEL3Tablet Docking Station

HUBLET INSTALL QUICK GUIDE JANNE BERGLUND Hublet Customer Install Quick Guide FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ➢ Reorient or relocate the receiving antenna. ➢ Increase the separation between the equipment and receiver. ➢ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ➢ Consult the dealer or an experienced radio/TV technician for help. ”changes or modifications not expressly approved by the Hublet Oy could void the user's authority to operate the equipment.” HUBLET INSTALL QUICK GUIDE JANNE BERGLUND These instructions apply when all technical details have been received from the customer. NOTE: These instructions will be updated, when the new Hublet Manager can be used to configure the entire customer account. Step 1: Create new SITE for customer. If customer already has a Site, the proceed to step 2. 1. Log into Hublet Manager as Distributor Organisation Admin (https://manager.hublet.fi/ui) 2. Click on “Sites” in the ACCOUNT menu 3. Click “Add site” 4. Enter SITE NAME and click “Add site” Step 2: Log into the Customer Site to begin configuration of Customer account 1. Click on the “Account selector” dropdown list on the top right corner of the Hublet Manager view 2. Click on the Distributor Org account on the top of the list that is opened 3. Locate the Site you wish to configure and click “Select” 4. You are now shown the Site level Dashboard Step 3: Invite a user from the Customer side to be a Site Admin and complete the following step (Google EMM enrolment) 1. Navigate to the correct Site with the Site selector 2. Click on “Users” in the ADMINISTRATION section of the Main menu 3. Click on “Invite user” 4. Enter users email address into the text field 5. Select the language you want to send the invitation email with 6. Click “Send invitation” ➔ The new user will receive an email with a link to register to the Hublet Manager to the Site you have initiated the invite from Step 4: Enrolling the Site to Google EMM for Google Play Store connectivity. NOTE: Each individual Site will need their own Google Account to enrol. HUBLET INSTALL QUICK GUIDE JANNE BERGLUND 1. Once on the Site level click on “Settings” in the ADMINISTRATION menu 2. Click “Edit” on the General information section to set the Site details (Address, Country, Timezone and Default language) 3. On the Google EMM section click “Enroll” to begin the enrolling process. a. NOTE: at this point you need to be logged into your browser with the correct Google account or be logged out of all Google accounts. The EMM enrolment process will automatically use the Google account you are currently logged into. 4. Log into the Google account if you are prompted to do so. Otherwise click “Get started” 5. Enter the Site name into the “Business name” field 6. Click “Next” to proceed 7. Optionally enter a Data Protection Officer and EU Representative or leave these fields empty for now and add them later. 8. Check the box “I have read and agree to the Managed Google Play agreement.” 9. Click “Confirm” 10. Click “Complete Registration” 11. Check that you have received the “Enterprise ID” in the Google EMM section of the Settings page in Hublet Manager. Step 5: Configuring the available Wifi networks for the Hublet Tablets. 1. Click on “Networks” on the ADMINISTRATION menu 2. Click “Add network” 3. Enter the SSID of the wifi network that will be used by the Hublet Tablets 4. Select the correct NETWORK SECURITY MODE 5. Select the NETWORK VISIBLITY (Broadcast or Hidden) 6. Enter the security settings based on the security mode selected 7. Click “Add network” Step 6: Add a Profile into the Site. Create the Profile 1. Click on “Profiles” in the ACCOUNT menu 2. Click on “Add profile” 3. Enter descriptive PROFILE NAME and DESCRIPTION 4. Click “Add profile” HUBLET INSTALL QUICK GUIDE JANNE BERGLUND Edit the Profile settings 5. Click on the Profile icon that appears on the Profiles page 6. Click “Change profile picture” to access Profile background image editing a. Click “Upload image button” b. Select the correct image from the file selection view c. Click “Save changes” 7. Click “Profile settings” to edit Profile basic settings a. Click “General” tab to view Profile Name and Description b. Click Edit to update the Name and/or Description c. Click “Save changes” 8. Click “Networks” to edit network connectivity settings on Profile level. Setting updates are autosaved. a. Tick the check box to add/remove network access for tablet when using the Profile b. Enable or disable mobile network access if tablet has mobile network connection available (SIM card) 9. Click “Tablets” to adjust Tablet audio, microphone and camera settings. The settings are autosaved when edited. a. Enable/Disable audio output to tablet speakers b. Set the Default audio volume (scale 0-10) c. Set Max audio volume possible for tablet (scale 0-10) d. Enable/Disable tablet microphone e. Enable/Disable tablet camera 10. Click “Loans” to adjust the tablet loan session max duration a. Select max duration from list or set custom time by selecting “Custom” from the list b. Exit the Settings by clicking the “X” on the top right corner Create a Category in which the content is added 1. In…

Text truncated - open the document above for the full version.

Hublet Oy Itälahdenkatu 22 B 00210 Helsinki, Finland Business ID: 2631894-9 gethublet.com To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Hublet Oy Itälahdenkatu 22b 00210 Helsinki Finland Regarding: Confidentiality Request regarding application for FCC ID 2AT23-M2-MODEL3 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Jari Veikkolainen HW Business Manager Hublet Oy

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Hublet Oy Address Itälahdenkatu 22b 00210 Helsinki Finland Grantee Code 2AT23 FCC ID 2AT23-M2-MODEL3 Authorized Contact Name Jari Veikkolainen Contact Email [email protected] Contact Phone +358505151617 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in ac cordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in ac cepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1)l abeling the equipment with the exact FCC ID as specified in this application, (2)compliance statement labeling pursuant to the applicable rules, (3)compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in ac cordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept t hat they are the responsible party and agree to abide by t heir responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in ac cordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1)the A pplicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has r ead, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:30.11.2022 Print Name: Jari Veikkolainen Title: HW Business Manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Docking station picture. Front side: Back side: Left side: Right side: Top side: Bottom side:

Type label positioning in Docking station:

FI text height 7.6mm logo height 9.0mm 1.7mm 2.1mm 1.7mm 10.7mm 7.7mm 8.0mm Print measurements document Print size : 60mm x 80mm 7.3mm 9.9mm Model: HUBLET-M2 Made in Finland INPUT 85 ~ 264VAC 1.6-2.8A 47 - 63 Hz FCC ID: 2AT23-M2-MODEL3 Contains FCC ID: 2ABCB-RPI4B Contains FCC ID: WP5TWN4F1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

View inside of docking station: Main Board back side: View inside of docking station: Raspberry Pi single board computer assembled: Raspberry Pi single board computer back side: Power supply: Additional pictures inside of docking station:

Reference number: HELEM2206000300-1 Page 1 of 15 These test results are valid for the tested unit only. This report shall not be reproduced, except in full, without a written permission of SGS Fimko. Test Report Electromagnetic Compatibility (EMC) HELEM2206000300-1 TESTS ACCORDING TO FCC PART 15 B AND ISED CANADA REQUIREMENTS Equipment Under Test: Hublet Smart Docking Station Model: Hublet-M2 Customer: Hublet Oy Itälahdenkatu 22 B 00210 Helsinki Finland FCC Rule Part: FCC CFR 47 Part 15 Subpart B, Class B IC Rule Part: ICES-003 Issue 7, Class B Date: 30 September 2022 Date: 4 October 2022 Issued by: Checked by: Lauri Sippola Rauno Repo Testing Engineer Senior EMC Specialist Reference number: HELEM2206000300-1 Page 2 of 15 Table of Contents TABLE OF CONTENTS TABLE OF CONTENTS ................................................................................................................................. 2 GENERAL REMARKS ................................................................................................................................... 3 Disclaimer ................................................................................................................................................. 3 RELEASE HISTORY...................................................................................................................................... 4 PRODUCT DESCRIPTION ............................................................................................................................ 5 Equipment Under Test (EUT) .................................................................................................................... 5 General description ................................................................................................................................... 5 Samples and modifications........................................................................................................................ 5 Ports and cables ....................................................................................................................................... 5 Peripherals ............................................................................................................................................... 6 TEST CONDITION ......................................................................................................................................... 7 EUT Test Conditions During EMC-Testing ................................................................................................. 7 Operation modes ...................................................................................................................................... 7 Emission Measurement Uncertainty .......................................................................................................... 7 SUMMARY OF TESTING .............................................................................................................................. 8 EMISSION TESTS ......................................................................................................................................... 9 Conducted Emissions In The Frequency Range 150 kHz - 30 MHz ........................................................... 9 Radiated Emissions In The Frequency Range 30 MHz - 18 GHz ............................................................... 11 TEST EQUIPMENT ....................................................................................................................................... 15 Radiated emissions ................................................................................................................................... 15 Conducted emissions ................................................................................................................................ 15 Reference number: HELEM2206000300-1 Page 3 of 15 Disclaimer GENERAL REMARKS Disclaimer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format docu- ments, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Condi- tions/Terms-e-Document.aspx Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written ap- proval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Reference number: HELEM2206000300-1 Page 4 of 15 Release History RELEASE HISTORY Version Changes Issued 1.0 Initial release 30 September 2022 Reference number: HELEM2206000300-1 Page 5 of 15 Product Description PRODUCT DESCRIPTION Equipment Under Test (EUT) EUT information General Product Description Hublet Smart Docking Station Model Hublet-M2 Serial number - Power input port type AC (L, N, PE) Rated voltage 100-120 VAC Rated current 3.0 A Rated frequency 60 Hz Rated power - EUT Highest operation freq. - Hardware Version (if any) - Software Version (if any) - Mechanical size of the EUT 59 x 126 x 59 cm Parallel models - Radio module or chip Integrated in Rasberry Pi (FCC ID: 2ABCB-RPI4B) The EUT was tested as a floor standing unit. Gen…

Text truncated - open the document above for the full version.

Reference number: HELEM2206000300-2 Page 1 of 18 These test results are valid for the tested unit only. This report shall not be reproduced, except in full, without a written permission of SGS Fimko. Test Report HELEM2206000300-2 INTENTIONAL RADIATOR TESTS ACCORDING TO FCC PART 15 C AND ISED CANADA REQUIREMENTS Equipment Under Test: Hublet Smart Docking Station Model: Hublet-M2 Customer / Manufacturer: Hublet Oy Itälahdenkatu 22 B 00210 Helsinki Finland FCC Rule Part: 15.225 IC Rule Part: RSS-210, Issue 10, 2019 RSS-GEN Issue 5 Amendment 2, 2021 - partial testing, see test suite for details Date: 30 September 2022 Date: 4 October 2022 Issued by: Checked by: Lauri Sippola Rauno Repo Testing Engineer Senior EMC Specialist Reference number: HELEM2206000300-2 Page 2 of 18 Table of Contents TABLE OF CONTENTS TABLE OF CONTENTS ................................................................................................................................. 2 GENERAL REMARKS ................................................................................................................................... 3 Disclaimer ................................................................................................................................................. 3 RELEASE HISTORY...................................................................................................................................... 4 PRODUCT DESCRIPTION ............................................................................................................................ 5 Equipment Under Test .............................................................................................................................. 5 General Description .................................................................................................................................. 5 Ratings and declarations ........................................................................................................................... 5 Power Supply ............................................................................................................................................ 5 Cables ...................................................................................................................................................... 5 Peripherals ............................................................................................................................................... 6 SUMMARY OF TESTING .............................................................................................................................. 7 EUT Test Conditions during Testing .......................................................................................................... 7 Test Facility............................................................................................................................................... 7 TEST RESULTS ............................................................................................................................................ 8 Antenna requirement ................................................................................................................................. 8 Conducted Emissions In The Frequency Range 150 kHz - 30 MHz. .......................................................... 9 Radiated Emissions 9 kHz to 1 GHz .......................................................................................................... 11 99% Occupied Bandwidth ......................................................................................................................... 14 20 dB Emission Bandwidth ........................................................................................................................ 16 TEST EQUIPMENT ....................................................................................................................................... 18 Reference number: HELEM2206000300-2 Page 3 of 18 Disclaimer Test Report template version: 1.1 GENERAL REMARKS Disclaimer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Reference number: HELEM2206000300-2 Page 4 of 18 Release History Test Report template version: 1.0 RELEASE HISTORY Version Changes Issued 1.0 Initial release 30 September 2022 Reference number: HELEM2206000300-2 Page 5 of 18 Product Description PRODUCT DESCRIPTION Equipment Under Test Equipment Under Test: Hublet Smart Docking Station Model: Hublet-M2 Serial no: - FCC ID: 2AT23-M2M3-MODEL2 IC: - Radio module or chip: Integrated in Rasberry Pi (FCC ID: 2ABCB-RPI4B) General Description Tablet docking station contains a power supply, PCB, Rasberry Pi single board computer and a barcode scanner and RFID card reader and has …

Text truncated - open the document above for the full version.

Reference number: HELEM2206000300-3 Page 1 of 15 These test results are valid for the tested unit only. This report shall not be reproduced, except in full, without a written permission of SGS Fimko. Test Report HELEM2206000300-3 INTENTIONAL RADIATOR TESTS ACCORDING TO FCC PART 15 E AND ISED CANADA REQUIREMENTS Equipment Under Test: Hublet Smart Docking Station Model: Hublet-M2 Customer / Manufacturer: Hublet Oy Itälahdenkatu 22 B 00210 Helsinki Finland FCC Rule Part: 15.407 IC Rule Part: RSS-247, Issue 2, 2017 RSS-GEN Issue 5 Amendment 2, 2021 KDB: 789033 D02 General U-NII Test Procedures New Rules v02r01 (December 14, 2017) - partial testing, see test suite for details Date: 30 September 2022 Date: 4 October 2022 Issued by: Checked by: Lauri Sippola Rauno Repo Testing Engineer Senior EMC Specialist Reference number: HELEM2206000300-3 Page 2 of 15 Table of Contents TABLE OF CONTENTS TABLE OF CONTENTS ................................................................................................................................. 2 GENERAL REMARKS ................................................................................................................................... 3 Disclaimer ................................................................................................................................................. 3 RELEASE HISTORY...................................................................................................................................... 4 PRODUCT DESCRIPTION ............................................................................................................................ 5 Equipment Under Test .............................................................................................................................. 5 General Description .................................................................................................................................. 5 Ratings and declarations ........................................................................................................................... 5 SUMMARY OF TESTING .............................................................................................................................. 6 EUT Test Conditions during Testing .......................................................................................................... 6 Test Facility............................................................................................................................................... 7 TEST RESULTS ............................................................................................................................................ 8 Antenna requirement ................................................................................................................................. 8 Transmitter Radiated Spurious Emissions 1 - 40 GHz ............................................................................... 9 TEST EQUIPMENT ....................................................................................................................................... 15 Reference number: HELEM2206000300-3 Page 3 of 15 Disclaimer GENERAL REMARKS Disclaimer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Reference number: HELEM2206000300-3 Page 4 of 15 Release History Test Report template version: 1.1 RELEASE HISTORY Version Changes Issued 1.0 Initial release 30 September 2022 Reference number: HELEM2206000300-3 Page 5 of 15 Product Description PRODUCT DESCRIPTION Equipment Under Test Model: Hublet-M2 Serial no: - FCC ID: 2AT23-M2M3-MODEL2 IC: - Radio module or chip: Integrated in Rasberry Pi (FCC ID: 2ABCB-RPI4B) General Description Tablet docking station contains a power supply, PCB, Rasberry Pi single board computer and a barcode scanner and RFID card reader and has slots for either 3 or 6 tablets. The docking station uses a 5 V internal voltage to power a tablet locking mechanism, indicator LED lights and the Rasberry Pi computer through the PCB. Tablet locking/release and the lights are controlled by the computer. The RFID reader (reading either 125 kHz or 13.56 MHz RFID tag) or barcode scanner are connected to the Rasperry Pi computer via USB 3.0, and they are used to read information from the customers, e.g. a library card, and the information is processed in the Rasberry Pi. The information can be sent to either the Hublet docking station owner’s information network or Hublet cloud service via either WLAN connection or Ethernet/LAN connection, depending on how the owner wants the dock connected. Through the interaction and information gotten from the server a tablet may be unlocked from the dock for the customer to use. Classification Fixed device Mob…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS Page 1 of 2 Project number: HELEM2206000300-1 SGS Fimko Ltd. Takomotie 8, FI-00380 Helsinki Finland t +358 9 6963 361 f +358 9 692 5474 www.sgs.fi Member of SGS Group (Société Générale de Surveillance) Photograph 1: Radiated emissions (30 – 1000 MHz) Photograph 2: Radiated emissions (1 – 18 GHz) TEST SETUP PHOTOGRAPHS Page 2 of 2 Project number: HELEM2206000300-1 SGS Fimko Ltd. Takomotie 8, FI-00380 Helsinki Finland t +358 9 6963 361 f +358 9 692 5474 www.sgs.fi Member of SGS Group (Société Générale de Surveillance) Photograph 3: Conducted emissions (0.150 – 30 MHz)

TEST SETUP PHOTOGRAPHS Page 1 of 2 Project number: HELEM2206000300-2 SGS Fimko Ltd. Takomotie 8, FI-00380 Helsinki Finland t +358 9 6963 361 f +358 9 692 5474 www.sgs.fi Member of SGS Group (Société Générale de Surveillance) Photograph 1: Transmitter spurious emissions (9 kHz – 30 MHz) Photograph 2: Transmitter spurious emission…

Text truncated - open the document above for the full version.