2AT2K-S020MSuvie Kitchen Robot

Multi-Zone Cooking and Refrigeration www.suvie.com This product is intended for HOUSEHOLD USE ONLY Model No. S020M Suvie Kitchen Robot User Manual F I L L W AT E R A B OV E T H E L I N E Ver. 04202101 Model No. S020M1Model No. S020M2 IMPORTANT SAFETY INSTRUCTIONS FCC (Federal Communications Commission) SAVE THESE INSTRUCTIONS To reduce the risk of burns, electric shock, fire, or injury to persons when using your Suvie, be sure to follow the basic safety precautions in this section. WARNING Spilled food can cause serious burns. Keep the appliance and cord away from children. Never drape the cord over the edge of a counter, never use an outlet below the counter, and never use an extension cord with this appliance. When using electrical appliances, ALWAYS follow basic safety precautions including all of the following: 1. Read all instructions. 2. Do not touch hot surfaces directly; use handles or knobs. 3. To protect against electrical shock do not immerse cord or plugs in water or other liquid. 4. Close supervision is necessary when any appliance is used by or near children. 5. Unplug from outlet before cleaning. Allow to cool before inserting or removing parts. 6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Contact [email protected] for examination, repair, or adjustment. 7. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. 8. Do not use outdoors. 9. Do not let the cord hang over the edge of a table or counter, or to touch hot surfaces. 10. Do not place on or near a hot gas or electric burner, or in a heated oven. 11. Extreme caution must be used when moving an appliance containing hot oil or other hot liquids. 12. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “off”, then remove plug from the wall outlet. 13. Do not use appliance for anything other than its intended use. 14. Use extreme caution when removing trays or disposing of hot water or grease. 15. Do not clean with metal scouring pads. Pieces can break off the pad and touch electrical parts, creating a risk of electric shock. 16. Intended for countertop use only. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device should be installed and operated with minimum 20 cm between the radiator and your body. The users manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Model No. S020M3Model No. S020M4 Before Using Your Suvie DANGER Do not operate Suvie if the cord or plug becomes damaged, if the appliance malfunctions, or if the Suvie is dropped or damaged in any manner. Contact Suvie immediately for examination, repair, or electrical or mechanical adjustment. WARNING • Place Suvie on a clean, solid, even surface to help prevent it from slipping. An anti- tip bracket may be attached to the back of the appliance and the wall behind it for extra stability, especially if there are young children in the house. • Never use the Suvie in combination with parts or equipment from older generations of Suvie. Never use your Suvie with damaged accessories. • The use of attachments or items not recommended or sold by Suvie may cause fire, electric shock, or injury. • The Suvie can generate a constant flow of steam while cooking. Keep away from any hot steam that escapes the appliance during operation. Steam may also leave traces of moisture on your countertop. Be mindful of objects that sit near your appliance. • Scalding due to food that has overheated may occur if attempting to use quantities of food in excess of a tray’s capacity. If overheating occurs, unplug the appliance and allow it to cool. Use care when removing all components as they may stay hot for some time. • To avoid scalding, burn injury, and laceration hazard, do not attempt to open the Suvie door by force. Only open the door when the program is complete. • Fire hazard: Keep Suvie away from outside heat sources to avoid risk of fire. • Trays will be hot: Always use an oven mitt when removing trays after cooking as they may be extremely hot. • Not intended for use by child…

Text truncated - open the document above for the full version.

C5266091_X8_Ed.1 1/1 Home Tech Innovation, Inc Letter of Authorization Company: Home Tech Innovation, Inc Address: 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 Product Name: Suvie Kitchen Robot Model Number: S020M FCC Identifier: 2AT2K-S020M We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Kevin Incorvia Date: 2021-05-13 Title: CTO Signature of applicant:

C5266091_X10_Ed.2 1/1 Home Tech Innovation, Inc Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021-05-13 Subject: Request for Confidentiality FCC ID: 2AT2K-S020M To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☒ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Kevin Incorvia

Document No: SHE2104017-02 Page 1 of 3 S020M External photo Front Back Document No: SHE2104017-02 Page 2 of 3 Left side Right side Document No: SHE2104017-02 Page 3 of 3 Top Bottom

Document No: SHE21040017-02 Page 1 of 1 Label Location

Document No: SHE2104017-02 Page 1 of 4 S020M Internal photo Internal 1 Internal 2 Document No: SHE2104017-02 Page 2 of 4 Internal 3 Internal 4 Document No: SHE2104017-02 Page 3 of 4 Internal 5 Internal 6 BT / WIFI Antenna Document No: SHE2104017-02 Page 4 of 4 Internal 7 Internal 8 NFC Antenna Wifi /BT chip BT / WIFI Antenna

MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 1 of 6 Applicant : Home Tech Innovation, Inc Address of Applicant : 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 Product Name : Suvie Kitchen Robot Model No. : S020M Sample No. : E21040017-01#01 FCC ID 2AT2K-S020M Standards : FCC Part 2.1093 OET Bulletin 65 Edition 97-01 June 2001 Date of Receipt : 2021-04-26 Date of Test : 2021-04-26 ~ 2021-05-17 Date of Issue : 2021-05-17 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Jennifer Zhou) (Oliver Xiang) (Authorized signatory: Guoyou Chi) MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 2 of 6 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 ENVIRONMENTAL CONDITIONS ................................................................................................................................................... 3 1.3 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.4 DETAILS OF EUT ........................................................................................................................................................................ 3 2 MAXIMUM PERMISSIBLE EXPOSURE (MPE) ................................................................................................................. 4 2.1 LIMITS ......................................................................................................................................................................................... 4 2.2 ASSESSMENT METHODS ............................................................................................................................................................. 4 2.3 TEST RESULT ............................................................................................................................................................................. 5 2.4 CONCLUSION .............................................................................................................................................................................. 5 3 APPENDIXES .......................................................................................................................................................................... 6 3.1 SAMPLE PHOTOGRAPH............................................................................................................................................................... 6 MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 3 of 6 1 General Information 1.1 Testing Laboratory Company Name ICAS Testing Technology Services (Shanghai) Co., Ltd. Address No.1298 Pingan Rd, Minhang District, Shanghai, China Telephone 0086 21-51682999 Fax 0086 21-54711112 Homepage www.icasiso.com 1.2 Environmental conditions Temperature (C) 18-25 Humidity (%RH) 40-65 Barometric Pressure (mbar) 960-1060 Ambient noise & Reflection（W/kg） < 0.012 1.3 Details of Application Company Name Home Tech Innovation, Inc Address 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 Contact Person Kevin Incorvia Telephone +1 617 800 5336 Email [email protected] Manufacturer Company Name Home Tech Innovation, Inc Address 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 1.4 Details of EUT Product Name Suvie Kitchen Robot Brand Name Suvie Test Model No. S020M FCC ID 2AT2K-S020M Mode of Operation WLAN 802.11b/g/n(HT20/40); Bluetooth BR/EDR/BLE Frequeny Range 2400MHz ~ 2483.5MHz Modulation Type DSSS, OFDM, GFSK, π/4-DQPSK, 8-DPSK Antenna Type Internal Antenna Antenna Gain 3.42 dBi Note(s): All applicable tests as described in test case and measurement sections were performed on model TC22H1. MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 4 of 6 2 Maximum Permissible Exposure (MPE) 2.1 Limits According to FCC Part 1.1307, systems operating under the provisions of this section shall be operated in a manner the ensures that the public is not exposed to radio frequency energy level in excess of the commission’s guidelines. 2.2 Assessment methods Calculation Formula from FCC OET 65: Where: S = Power Density (mW/cm2) P = Input Power of the Antenna (mW) G = Antenna Gain Relative to an Isotropic Antenna R = Distance from the Antenna to the Point of Investigation (cm) MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 5 of 6 2.3 Test Result Operation Mode Frequency Range (MHz) Max Conducted Power (dBm) Antenna Gain (dBi) Max EIRP (mW) Power Density at R = 20 cm (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2.4GHz 2400 ~ 2483.5 18.21 3.42 145.55 0.0290 1.0 Bluetooth 2400 ~ 2483.5 3.96 3.42 5.47 0.0011 1.0 BLE 2400 ~ 2483.5 1.06 3.42 2.81 0.0006 1.0 Note(s): For 300 – 1,500MHz: Power Density limit is f/1500 mW/cm 2 For 1,500 – 100,000MHz: Power Density limit is 1.0 mW/cm 2 2.4 Conclusion The Power Density at the position which is 20 cm far from the EUT is smaller than the General Population/Uncontrolled Exposure limit. MPE TEST REPORT Report No.: SHE21040017-02DE Date: 2021-05-17 Page 6 of 6 3 Appendixes 3.1 Sample Photograph Front of the sample Rear of the sample ***End of the report***

TEST REPORT Report No.: SHE21040017-02AE Date: 2021-05-17 Page 1 of 35 Applicant : Home Tech Innovation, Inc Address of Applicant : 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 Product Name : Suvie Kitchen Robot Model No. : S020M Sample No. : E21040017-01#01 FCC ID : 2AT2K-S020M Standards : FCC CFR47 Part 15, Subpart C Date of Receipt : 2021-04-26 Date of Test : 2021-04-26 ~ 2021-05-17 Date of Issue : 2021-05-17 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Jennifer Zhou) (Oliver Xiang) (Authorized signatory: Guoyou Chi) TEST REPORT Report No.: SHE21040017-02AE Date: 2021-05-17 Page 2 of 35 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.3 DETAILS OF EUT ........................................................................................................................................................................ 3 1.4 TEST METHODOLOGY ................................................................................................................................................................. 4 1.5 TEST SUMMARY .......................................................................................................................................................................... 5 2 TEST CONDITION .................................................................................................................................................................. 6 2.1 ENVIRONMENTAL CONDITIONS ................................................................................................................................................... 6 2.2 EQUIPMENT LIST ........................................................................................................................................................................ 6 2.3 MEASUREMENT UNCERTAINTY................................................................................................................................................... 6 3 TEST SET-UP AND OPERATION MODES ........................................................................................................................ 7 3.1 DETAILS OF TEST MODE ............................................................................................................................................................ 7 3.2 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ................................................................................................................ 7 3.3 SUPPORT SOFTWARE ................................................................................................................................................................. 7 3.4 TEST SETUP DIAGRAM ............................................................................................................................................................... 8 4 TEST RESULTS .................................................................................................................................................................... 10 4.1 TRANSMITTER REQUIREMENT & TEST SUITES ........................................................................................................................ 10 4.1.1 Antenna Requirement ..................................................................................................................................................... 10 4.1.2 Peak Output Power.......................................................................................................................................................... 11 4.1.3 6dB Bandwidth and 99% Bandwidth ............................................................................................................................. 14 4.1.4 Power Spectral Density ................................................................................................................................................... 18 4.1.5 Conducted Spurious Emission & Authorized-band band-edge ................................................................................. 21 4.1.6 Radiated Spurious Emission .......................................................................................................................................... 28 4.1.7 Band Edge (Restricted-band band-edge) .................................................................................................................... 29 4.2 MAINS EMISSIONS .................................................................................................................................................................... 30 4.2.1 Conducted Emission on AC Mains ................................................................................................................................ 30 5 APPENDIXES ........................................................................................................................................................................ 33 5.1 PHOTOGRAPHS OF THE SAMPLE .............................................................................................................................................. 33 5.2 SET-UP FOR CONDUCTED EMISSIONS ...................................................................................…

Text truncated - open the document above for the full version.

TEST REPORT Report No.: SHE21040017-02CE Date: 2021-05-17 Page 1 of 62 Applicant : Home Tech Innovation, Inc Address of Applicant : 1035 Cambridge St, Suite 11A, Cambridge, MA 02141 Product Name : Suvie Kitchen Robot Model No. : S020M Sample No. : E21040017-01#01 FCC ID : 2AT2K-S020M Standards : FCC CFR47 Part 15, Subpart C Date of Receipt : 2021-04-26 Date of Test : 2021-04-26 ~ 2021-05-17 Date of Issue : 2021-05-17 Remark: This report details the results of the testing carried out on one sample, the results contained in this report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. Prepared by： Reviewed by： Approved by： (Jennifer Zhou) (Oliver Xiang) (Authorized signatory: Guoyou Chi) TEST REPORT Report No.: SHE21040017-02CE Date: 2021-05-17 Page 2 of 62 Contents 1 GENERAL INFORMATION ................................................................................................................................................... 3 1.1 TESTING LABORATORY ............................................................................................................................................................... 3 1.2 DETAILS OF APPLICATION .......................................................................................................................................................... 3 1.3 DETAILS OF EUT ........................................................................................................................................................................ 3 1.4 TEST METHODOLOGY ................................................................................................................................................................. 4 1.5 TEST SUMMARY .......................................................................................................................................................................... 4 2 TEST CONDITION .................................................................................................................................................................. 5 2.1 TEST FACILITY ............................................................................................................................................................................ 5 2.2 ENVIRONMENTAL CONDITIONS ................................................................................................................................................... 5 2.3 EQUIPMENT LIST ........................................................................................................................................................................ 5 2.4 MEASUREMENT UNCERTAINTY................................................................................................................................................... 5 3 TEST SET-UP AND OPERATION MODES ........................................................................................................................ 6 3.1 DETAILS OF TEST MODE ............................................................................................................................................................ 6 3.2 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ................................................................................................................ 7 3.3 SUPPORT SOFTWARE ................................................................................................................................................................. 7 3.4 TEST SETUP DIAGRAM ............................................................................................................................................................... 8 4 TEST RESULTS .................................................................................................................................................................... 10 4.1 TRANSMITTER REQUIREMENT & TEST SUITES ........................................................................................................................ 10 4.1.1 Antenna Requirement ..................................................................................................................................................... 10 4.1.2 Peak Output Power.......................................................................................................................................................... 11 4.1.3 6dB Bandwidth and 99% Bandwidth ............................................................................................................................. 12 4.1.4 Power Spectral Density ................................................................................................................................................... 25 4.1.5 Conducted Spurious Emission & Authorized-band band-edge ................................................................................. 32 4.1.6 Radiated Spurious Emission .......................................................................................................................................... 55 4.1.7 Band Edge (Restricted-band band-edge) .................................................................................................................... 56 4.2 MAINS EMISSIONS .................................................................................................................................................................... 57 4.2.1 Conducted Emission on AC Mains ................................................................................................................................ 57 5 APPENDIXES ........................................................................................................................................................................ 60 5.1 PHOTOGRAPHS OF THE SAMPLE .......................................................................…

Text truncated - open the document above for the full version.

Document number ：SHE21040017-02AE Page 1 of 18 EXHIBIT A- RADIATED SPURIOUS EMISSION DATA Note : Transmit frequency is ignore ,mark 30M-1G BLE-Horizontal-TX 英格尔 Te s t r e s u l t P r o j e c t N u m b e r : 验证测试 Te s t T i m e : 2 0 2 1-05-0 8 _ 1 1 . 3 5 . 1 7 E U T N a m e : N . A Te s t E n g in e e r : X ia n g C h e n g J ie M a n u f a c t u r e r : N . A Te s t S t a n d a r d : F C C M o d e l: N . A W o r k A d d it io n : N o r m a l Te m p . ( o C ) : 2 0 . 1 Load: N . A H u m . : 54% R e m a r k : DR-R E 0 1-E 2 1 0 4 0 0 1 7-0 1 # 0 1 N o . F r e q u e n c y ( M H z ) R e s u lts ( d B u V /m ) F a c t o r ( d B ) L im it ( d B u V /m ) O v e r L im it ( d B ) D e t e c t o r Ta b le ( D e g r e e ) H e ig h t ( c m ) A n t e n n a V e r d ic t 1 3 0 . 7 2 7 2 4 . 2 8 -2 4 . 0 6 4 0 . 0 -1 5 . 7 2 P e a k 1 0 5 . 4 0 200 H o r iz o n t a l P a s s 2 7 1 . 9 4 2 2 8 . 1 8 -2 4 . 2 5 4 0 . 0 -11 . 8 2 P e a k 3 1 0 . 6 0 300 H o r iz o n t a l P a s s 3 1 4 4 . 1 8 9 3 9 . 7 5 -2 4 . 2 8 4 3 . 5 -3 . 7 5 P e a k 1 6 1 . 7 0 200 H o r iz o n t a l P a s s 4 2 5 6 . 4 2 6 4 0 . 7 0 -1 8 . 4 9 4 6 . 0 -5 . 3 0 P e a k 2 9 1 . 1 0 100 H o r iz o n t a l P a s s 4* 2 5 6 . 4 2 6 3 9 . 1 6 -1 8 . 4 9 4 6 . 0 -6 . 8 4 QP 2 9 1 . 1 0 100 H o r iz o n t a l P a s s 5 5 0 3 . 9 6 9 3 4 . 0 9 -1 2 . 4 7 4 6 . 0 -11 . 9 1 P e a k 3 6 0 . 0 0 300 H o r iz o n t a l P a s s 6 8 9 9 . 8 7 3 3 5 . 2 3 -4 . 0 2 4 6 . 0 -1 0 . 7 7 P e a k 6 2 . 3 0 300 H o r iz o n t a l P a s s Document number ：SHE21040017-02AE Page 2 of 18 BLE-Vertical-TX 英格尔 Te s t r e s u l t P r o j e c t N u m b e r : 验证测试 Te s t T i m e : 2 0 2 1-05-0 8 _ 1 1 . 2 6 . 0 9 E U T N a m e : N . A Te s t E n g in e e r : X ia n g C h e n g J ie M a n u f a c t u r e r : N . A Te s t S t a n d a r d : F C C M o d e l: N . A W o r k A d d it io n : N o r m a l Te m p . ( o C ) : 2 0 . 1 Load: N . A H u m . : 54% R e m a r k : DR-R E 0 1-E 2 1 0 4 0 0 1 7-0 1 # 0 1 N o . F r e q u e n c y ( M H z ) R e s u lts ( d B u V /m ) F a c t o r ( d B ) L im it ( d B u V /m ) O v e r L im it ( d B ) D e t e c t o r Ta b le ( D e g r e e ) H e ig h t ( c m ) A n t e n n a V e r d ic t 1 3 3 . 1 5 2 3 5 . 7 3 -2 3 . 6 4 4 0 . 0 -4 . 2 7 P e a k 4 8 . 0 0 100 V e r t ic a l P a s s 2 7 1 . 9 4 2 3 0 . 8 5 -2 4 . 2 5 4 0 . 0 -9 . 1 5 P e a k 3 6 0 . 0 0 200 V e r t ic a l P a s s 3 11 9 . 9 4 5 3 4 . 2 3 -2 2 . 7 1 4 3 . 5 -9 . 2 7 P e a k 2 6 4 . 3 0 100 V e r t ic a l P a s s 4 1 4 4 . 1 8 9 3 3 . 5 1 -2 4 . 2 8 4 3 . 5 -9 . 9 9 P e a k 1 0 7 . 6 0 100 V e r t ic a l P a s s 5 5 0 3 . 9 6 9 3 4 . 5 8 -1 2 . 4 7 4 6 . 0 -11 . 4 2 P e a k 3 5 4 . 2 0 100 V e r t …

Text truncated - open the document above for the full version.