2AU4P-QM5004PQRWIRELESS CHARGING POWER BANK

FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

TennRich International Corp. U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: September 15, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2AU4P-QM5004PQR TennRich International Corp.(“the applicant”) certifies that, as of the date of the filing of the application, GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. FRN: 0037700671 Address: 350 NORTHERN BLVD STE 324-1331, ALBANY, NY, 12204, USA Signature: Contact Person: David Kim Tel: (213)849-1481 Email: [email protected] Applicant Company Name: TennRich International Corp. FRN: 0028973394 Address: 1-3, Alley 5, Lane 305, Sec 1, Shin Nan Road, Lu Chu District, Taoyuan City, Taiwan 338 China. Signature: Contact Person: Yuna Hung Tel: 886-3-3124888-1809 Email: [email protected]

Rev 6/05/2026 TennRich International Corp. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AU4P-QM5004PQR [TennRich International Corp.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [TennRich International Corp.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Yuna Hung Rev 6/05/2026 TennRich International Corp. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AU4P-QM5004PQR [TennRich International Corp.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Yuna Hung

TennRich International Corp. Date: September 15, 2026 Product Model Number: QM5004PQ FCC ID: 2AU4P-QM5004PQR To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature： By: Yuna Hung Title: Certification Commissioner Email: [email protected] Telephone: 886-3-3124888-1809 On behalf of: TennRich International Corp.

TennRich International Corp. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 15, 2026 Subject; Request for Confidentiality FCC ID: 2AU4P-QM5004PQR To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature： By: Yuna Hung Title: Certification Commissioner

Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Annex A. EUT External Photos Model: QM5004PQ EUT View 1 EUT View 2 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR EUT View 3 EUT View 4 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR EUT View 5 EUT View 6 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR EUT View 7 EUT View 8

Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Annex D. Label FCC Label Sample FCC Labe Size: 2cm x 1cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Annex B. EUT Internal Photos EUT View 1 EUT View 2 Coil ANT Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR EUT View 3 EUT View 4 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR EUT View 5

Report No: SSP26080395-2 MPE Test Report Page 1 of 12 MPE Test Report FCC ID: 2AU4P-QM5004PQR Report No. : SSP26080395-2 Applicant : TennRich International Corp. Product Name : WIRELESS CHARGING POWER BANK Model Name : QM5004PQ Test Standard : FCC CFR 47 PART 1, 1.1310 Date of Issue : 22026-09-14 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26080395-2 MPE Test Report Page 2 of 12 Test Report Basic Information Applicant..................................: TennRich International Corp. Address of Applicant...............: 1-3, Alley 5, Lane 305, Sec 1, Shin Nan Road, Lu Chu District, Taoyuan City, Taiwan 338 China. Manufacturer..........................: Recharge Intelligent Technology (Ji'an) Co., Ltd. Address of Manufacturer........: 1st Floor, No. 14 Green Industrial Park, East District Of High Tech Zone, Suichuan County, Ji An, Jiangxi, 343900, China Product Name.........................: WIRELESS CHARGING POWER BANK Brand Name.............................: Energizer Main Model..............................: QM5004PQ Series Models..........................: N/A Test Standard..........................: FCC CFR 47 PART 1, 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Test .............................: 2026-08- 28 to 2026-09-07 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26080395-2 MPE Test Report Page 3 of 12 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Test Facilities ........................................................................................................................................................7 1.4 List of Measurement Instruments ..........................................................................................................................7 1.5 Measurement Uncertainty .....................................................................................................................................7 2. RF Exposure .................................................................................................................................................................8 2.1 Standard and Limit................................................................................................................................................8 2.2 Test Procedures ....................................................................................................................................................8 2.3 Test Setup Block Diagram ......................................................................................................................................9 2.4 Test Data and Results .......................................................................................................................................... 10 Annex A. Test Photos ..................................................................................................................................................... 12 Report No: SSP26080395-2 MPE Test Report Page 4 of 12 Revision History Revision Issue Date Description Revised By V1.0 2026-09-14 Initial Release Lahm Peng Report No: SSP26080395-2 MPE Test Report Page 5 of 12 1. General Information 1.1 Product Information Product Name: WIRELESS CHARGING POWER BANK Trade Name: Energizer Test Model: QM5004PQ Series Models: N/A Rated Voltage: Type-C Input: DC 5V/3A, 9V/2A, 12V/1.5A Type-C Output: DC 5V/3A, 9V/2.22A, 12V/1.67A 20W (Max) USB Output: DC 5V/3A, 9V/2A, 12V/1.5A 18W (Max) Wireless Output: 5W/7.5W/10W/15W Battery: 18Wh (5000mAh, 3.6V) Test Sample No: SSP26080395-1 Hardware Version: V1.0 Software Version: V1.0 Note 1: The test data is gathered from a production sample, provided by the manufacturer. Wireless Specification Wireless Standard: WPC (QI) Operating Frequency: Wireless charging Output(Phone):110.5kHz-205kHz, Modulation: ASK Antenna Gain: 0dBi Type of Antenna: Coil Antenna Type of Device: Portable Device Mobile Device Modular Device Report No: SSP26080395-2 MPE Test Report Page 6 of 12 1.2 Test Setup Information List of Test Modes Test Mode Description Remark TM1 Wireless charging 5W - TM2 Wireless charging 7.5W - TM3 Wireless charging 10W - TM4 Wireless charging 15W - TM5 Wireless charging 5W+Charging - Note: All modes of the main model and accessory models mentioned above have been tested. The report only shows the worst modes of the main model: TM4 data. List and Details of Auxiliary Cable Description Length (cm) Shielded/Unshielded With/Without Ferrite USB 100cm Unshielded Without Ferrite - - - - List and Details of Auxiliary Equipment Equipment Model Serial No. Manufacturer Adapter UGREEN CD289 - Mobile phone iPhone 16 HYG6PQMWK Apple Report No: SSP26080395-2 MPE Test Report Page 7 of 12 1.3 Test Facilities Laboratory Name: Shenz…

Text truncated - open the document above for the full version.

1 / 7 RuiChong Smart Technology (Ji'an) Co., Ltd. Sample Acknowledgment Form Number：A0 supplier Material name wireless transmitting coil Competent Material Quality PC95 Part number 03020800084 Material description ROHS/A11-G42.5*5.3*0.65-0.08*24*2P-10T/ 6.5UH20%-50MM supplier Dongguan Jerice Technology Co. , Ltd. manufacturer Manufacturer model Production address 96 Long Wu Road, Tai Ling Shan, Dongguan (3F, building L, Kam Hung Tat Science and Technology Park) Number of samples Sample signing date 2026.9.15 September 15, 2026 Environmental protection costs ten □RoHS □非RoHS Material properties □Plastic (structure) □Hardware screws □electronics □Packaging □accessories □another Quality audit Project review Business review RuiChong Confirm single person Confirm the details signature Date Purchasing Provide sample specifications and actual products, along with supplier test reports, environmental reports, and safety compliance reports Settle the bill Appearance, structure, material and manufacturing process, dimension testing, drawings, compatibility, marking key features electronics Functions, electrical performance, parameters, schematics, specifications, sample testing, clarify test items and gases engineering Structure, manufacturing process, trial assembly, functionality, electrical performance Quality Reliability testing, standards, and completeness of sample documentation Sales Color, appearance, packaging specifications, material and craftsmanship, structural dimensions, graphic printing, instruction manual content, etc. Permission granted File Revision History 2 / 7 Version Change content Date Notes V1.0 Optimize content and material requirements (first initial version) 注意事项 Attention 1.The sample acknowledgment form is in six copies, with one copy provided for each sample. Each sample must be inspected and confirmed 2.The sample must be signed off on by both parties for confirmation 3.The material information provided above must match the BOM in OneCloud 4.Before bulk delivery, the supplier must receive samples that have been signed by both parties and authorized for release by RuiChong DCC 5.Both parties must use the relevant material inspection standards and reliability test standards provided by Ruichong as the final basis for quality inspection 6.The customer needs to submit confirmation and add ψ when required 7.Acknowledgment form distribution units: Purchasing, R&D, Quality IQC, Suppliers 8.For the sample acknowledgment requirements and document list, please refer to Document 2 3 / 7 一、 Table of contents： 1. Cover.................................................................................1-2 2. Table of contents..................................................................3-3 3. Product drawings.................................................................. 4-4 4. A plan.................................................................................5-5 5. Product parameters...............................................................第6-6 6. Electrical parameters............................................................... 6-6 7. Bill of materials.....................................................................6-6 8. Packaging..............................................................................7-7 4 / 7 二、Product drawing： 5 / 7 三、A plan：Unit:MM 6 / 7 四． Product parameters： TurnsWire Dia The way of winding is sparse/dense Direction of winding Intersection yes/No Positive/negative coil 1-2 /10TS 0.08*24*2P Hot Air Strand Encircling Counterclockwi se Yes Counter-post All materials required to meet ROHS standards 五． Electrical characteristics： temperature：25º±10C Shiguang：65º±10% Temperature: 25O ± 10c humidity: 65o ± 10% NO Project Terminal Standards Test conditions Test equipment 1 IND 1-2 PIN and disk： Dianbu：6.5UH±20% Q：≧45 DCR：50m±10% 100kHz/ 1.0Vrms LCZ METER 1062A 六． Bill of materials： NO Name of material Description of product name Material Code Vendor Code 1 Wire 0.08*24*2P Hot Air Strand JR-RQ-0047 WH 2 Ferrite G42.5*5.3*0.65MM Hard magnetic sheet HI-012 TK 3 Double-sided glue 40x8mm diameter with hole (with tear-off tab) OT-17 HH 4 White glue transparent adhesive tap BI-0001 BY 5 T in strips Environmentally friendly lead-free solder rod BI-0001 QD 6 High temperature 6MM JD--0005 LK 7 / 7 七、Packaging： Figure 1: Single-layer foam tray, 1 box packing 560 pcs Figure 2: Uniform Direction Line head up neatly into the disk Figure 3: put into the packing box, each box put 5 layers Figure 4: sealing the box with transparent glue Figure 5: Packaging labelFigure 6: materials stacked, neat, labels to facilitate the search for materials

Report No: SSP26080395-1 FCC Test Report Page 1 of 27 FCC TEST REPORT FCC ID: 2AU4P-QM5004PQR Report No. : SSP26080395-1 Applicant : TennRich International Corp. Product Name : WIRELESS CHARGING POWER BANK Model Name : QM5004PQ Test Standard : FCC Part 15 Subpart C Date of Issue : 2026-09-14 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26080395-1 FCC Test Report Page 2 of 27 Test Report Basic Information Applicant..................................: TennRich International Corp. Address of Applicant...............: 1-3, Alley 5, Lane 305, Sec 1, Shin Nan Road, Lu Chu District, Taoyuan City, Taiwan 338 China. Manufacturer..........................: Recharge Intelligent Technology (Ji'an) Co., Ltd. Address of Manufacturer........: 1st Floor, No. 14 Green Industrial Park, East District Of High Tech Zone, Suichuan County, Ji An, Jiangxi, 343900, China Product Name.........................: WIRELESS CHARGING POWER BANK Brand Name.............................: Energizer Main Model..............................: QM5004PQ Series Models..........................: N/A Test Standard..........................: FCC Part 15 Subpart C ANSI C63.4-2014 ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024 Date of Test .............................: 2026-08- 28 to 2026-09-07 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26080395-1 FCC Test Report Page 3 of 27 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................8 2. Summary of Test Results .............................................................................................................................................9 3. Antenna Requirement ............................................................................................................................................... 10 3.1 Standard and Limit.............................................................................................................................................. 10 3.2 Test Result .......................................................................................................................................................... 10 4. Conducted Emissions ................................................................................................................................................ 11 4.1 Standard and Limit.............................................................................................................................................. 11 4.2 Test Procedure.................................................................................................................................................... 11 4.3 Test Data and Results .......................................................................................................................................... 12 5. Radiated Emissions ................................................................................................................................................... 15 5.1 Standard and Limit.............................................................................................................................................. 15 5.2 Test Procedure.................................................................................................................................................... 15 5.3 Test Data and Results .......................................................................................................................................... 17 6. Occupied Bandwidth ................................................................................................................................................. 26 6.1 Standard and Limit.............................................................................................................................................. 26 6.2 Test Procedure.................................................................................................................................................... 26 6.3 Test Data and Results ................................................................…

Text truncated - open the document above for the full version.

Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View 1 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Radiated Emission Test View 2 Radiated Emission Test View 3 Report No: SSP26080395-1 FCC ID: 2AU4P-QM5004PQR Radiated Emission Test View 4