2AUBX-TX01ZTX01Z Remote Control

TX01Z Remote Control This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmf ul interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential install ation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one o r more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.FCC ID: 2AUBX –TX01Z

S20101204303 Model: TX01Z N20191017V1 ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 S20101204303 Model: TX01Z N20191017V1 Photo 3 Photo 4 S20101204303 Model: TX01Z N20191017V1 Photo 5 Photo 6

Label and its Location Size: 35*25mm

S20101204303 Model: TX01Z N20191017V1 Photo 7 Photo 8 Ant S20101204303 Model: TX01Z N20191017V1 Photo 9 Photo 10 S20101204303 Model: TX01Z N20191017V1 Photo 11

version01 Dongguan Solid Model Technology Co., Ltd Declaration concerning Antenna Specification It is hereby declared that the product Model No.: TX01Z FCC ID: 2AUBX-TX01Z fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for Cable Antenna antenna type(s) described below: Model No. of antenna: N/A Type of antenna: Cable Antenna(1/4 wave antenna) GFSK: Gain of the antenna: 0 dBi Frequency range: 2418 to 2465 MHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Dongguan Solid Model Technology Co., Ltd Address: 3/F, Building B, 3rd Industry Zone, Matigang, Dalingshan Town, Dongguan City, China 523810 City: Dongguan ZIP / Postal code: Country: China Place: Dongguan Date: 11/09/2020 Signature:

Report No.: S20101204301001 Version.1.3 Page 1 of 46 RADIO TEST REPORT FCC ID: 2AUBX-TX01Z Product: TX01Z Remote Control Trade Mark: N/A Model No.: TX01Z Family Model: N/A Report No.: S20101204301001 Issue Date: 30 Oct. 2020 Prepared for Dongguan Solid Model Technology Co., Ltd 3/F, Building B, 3rd Industry Zone, Matigang, Dalingshan Town, Dongguan City, China 523810 Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen 518126 P.R. China Tel:400-800-6106 , 0755-3699-5508 Website:http://www.ntek.org.cn Report No.: S20101204301001 Version.1.3 Page 2 of 46 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ...................................................................................................................... 3 2 SUMMARY OF TEST RESULTS ......................................................................................................................... 4 3 FACILITIES AND ACCREDITATIONS ............................................................................................................. 5 3.1 FACILITIES..................................................................................................................................................... 5 3.2 LABORATORY ACCREDITATIONS AND LISTINGS ................................................................................. 5 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................... 5 4 GENERAL DESCRIPTION OF EUT .................................................................................................................. 6 5 DESCRIPTION OF TEST MODES ..................................................................................................................... 8 6 SETUP OF EQUIPMENT UNDER TEST ........................................................................................................... 9 6.1 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ....................................................................... 9 6.2 SUPPORT EQUIPMENT ............................................................................................................................... 10 6.3 EQUIPMENTS LIST FOR ALL TEST ITEMS .............................................................................................. 11 7 TEST REQUIREMENTS .................................................................................................................................... 13 7.1 CONDUCTED EMISSIONS TEST ............................................................................................................... 13 7.2 RADIATED SPURIOUS EMISSION ............................................................................................................ 15 7.3 6DB BANDWIDTH ....................................................................................................................................... 24 7.4 DUTY CYCLE ............................................................................................................................................... 25 7.5 PEAK OUTPUT POWER .............................................................................................................................. 27 7.6 POWER SPECTRAL DENSITY ................................................................................................................... 28 7.7 CONDUCTED BAND EDGE MEASUREMENT......................................................................................... 30 7.8 SPURIOUS RF CONDUCTED EMISSIONS ................................................................................................ 31 7.9 ANTENNA APPLICATION .......................................................................................................................... 32 8 TEST RESULTS ................................................................................................................................................... 33 8.1 MAXIMUM CONDUCTED OUTPUT POWER ....................................................................................................... 33 8.2 OCCUPIED CHANNEL BANDWIDTH .................................................................................................................. 35 8.3 MAXIMUM POWER SPECTRAL DENSITY LEVEL ............................................................................................... 39 8.4 BAND EDGE .................................................................................................................................................... 41 8.5 CONDUCTED RF SPURIOUS EMISSION ............................................................................................................. 43 Report No.: S20101204301001 Version.1.3 Page 3 of 46 1 TEST RESULT CERTIFICATION Applicant’s name ......................... : Dongguan Solid Model Technology Co., Ltd Address ....................................... : 3/F, Building B, 3rd Industry Zone, Matigang, Dalingshan Town, Dongguan City, China 523810 Manufacturer's Name .................. : Dongguan Solid Model Technology Co., Ltd Address ....................................... : 3/F, Building B, 3rd Industry Zone, Matigang, Dalingshan Town, Dongguan City, China 523810 Product description Product name .............................. : TX01Z Remote Control Model and/or type reference ..... : TX01Z Family Model ............................... : N/A Measurement Procedure Used: APPLICABLE STANDARDS APPLICABLE STANDARD/ TEST PROCEDURE TEST RESULT FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C KDB 174176 D01 Line Conducted FAQ v01r01 ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Complied This device described above has been tested by Shenzhen NTEK Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested s…

Text truncated - open the document above for the full version.

FCC ID: 2AUBX–TX01Z Radiated Measurement Photos