2AUYFRMX3760Mobile Phone with GSM, WCDMA, LTE, WiFi, Bluetooth and NFC

V0.1 5007521 RMX3760 English When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with temperature ranging from 5 °C~35°C. How to reboot the phone Press and hold the Power Button and Volume Up Button at the same time until the realme boot animation is displayed to reboot the phone. This guide will show you how to use the phone and its important functions. You may also visit realme ocial website to get more information about the phone. Greetings from realme mobile Warning Do not place the phone or battery near or inside heating equipment, cooking equipments, high pressure vessels (such as microwave ovens, induction cooker, electric oven, heater, pressure cooker, water heater, gas stove, etc.) to prevent the battery overheating which may lead to an explosion. Back cover can’t be removed. The original charger, data cable and battery shall be used. Unapproved chargers, data cables, or batteries that are not certied by the manufacturer may result in electric shock, re, explosion, or other hazards. realme mobile vous souhaite la bienvenue realme ses fonctionnalités importantes. Le couvercle arrière ne peut pas être enlevé. Vous devez utiliser le chargeur, le câbles de donées et la batterie d'origine. L'utilisation non approuvée de chargeurs, câbles de donées ou batteries qui ne sont pas certiés par le fabricant peut causer des décharges électriques, incendies, explosions ou d'autres dangers. Ne placez pas le téléphone ou la batterie à proximité d'équipements de chauage, de cuisson, de récipients à haute pression (comme un four à micro-ondes, une plaque à induction, un four électrique, un radiateur, un autocuiseur, un chaue-eau, une cuisinière à gaz, etc.) ni à l'intérieur de ces derniers pour éviter la surchaue de la batterie qui pourrait provoquer une explosion. Avertissement Lors du chargement, placez l'appareil dans une pièce à température ambiante et parfaitement aérée. Il est recommandé de mettre l'appareil en charge dans un environnement dont la température varie entre 5 °C et 35 °C. Maintenez les boutons de marche/arrêt et d'augmentation de volume enfoncés simultanément jusqu'à ce que l'animation de démarrage realme s'ache pour redémarrer le téléphone. Comment redémarrer le téléphone FCC SAR Français Español Esta guía le mostrará el uso del teléfono además de sus funciones más importantes. También, puede visitar nuestra página web ocial de realme donde obtendrá mayor información sobre el mismo. Bienvenido a realme mobile Recomendamos somente o uso de acessórios originais que acompanham o seu telefone realme. O uso de acessórios não certicados pelo fabricante poderá prejudicar o funcionamento e causar danos irreparáveis ao seu telefone. Não coloque o telefone perto de equipamentos de aquecimento, eletrodomésti- cos de cocção, utensílios de alta pressão (como fornos micro-ondas, aparelho de indução, forno elétrico, aquecedor, panelas elétricas, aquecedores de água, fornos a gás etc.) para evitar o superaquecimento da bateria. Aviso Português Advertencia No coloque el teléfono o la batería cerca o dentro de equipos de calefacción, electrodomésticos (microondas, cocinas de cualquier tipo, hornos de cualquier tipo o calefactores etc.), menaje de cocina (ollas a presión etc.), para evitar que la batería se sobrecaliente y/o provoque daños en su dispositivo. Debe utilizar el cargador, cable y batería originales. Los cargadores, cables o baterías que no cuenten con la autorización y la certicación del fabricante pueden derivar en diversos problemas como; descargas elétricas, incendios, explosiones, daños en la batería u otros peligros. Al cargar el dispositivo, colóquelo en un entorno que tenga una temperatura ambiente y ventilación normales. Es recomendable que el dispositivo sea cargado en un entorno con una temperatura que oscile entre 5 °C y 35 °C. La carcasa trasera no es extraible. NOTA: Para realizar la conguración inicial (al adquirir el dispositivo o realizar un reseteo de fábrica) es necesario conectarse a una red de datos (WiFi / Datos móviles). Si no se tiene disponible la red de datos, realice la conguración sin tarjeta SIM insertada. Especificaciones técnicas 4880mAh/18,98Wh(Min) 5000mAh/19,45Wh(Typ) XXX W/kg(Cabeza) XXX W/kg(Cuerpo) FCC SAR RMX3760 167,26×76,67×7,49(mm) Batería Producto Dimensiones Valores SAR Tamaño de la pantalla 0°C-35°C Temperatura para el correcto funcionamiento 17,13cm(6,74 Pulgadas) Características Eléctricas Entrada100-240Vca 50/60Hz 1,2A 5Vcc 2A ó 5-11Vcc 3ASalida Especicación Eléctrica del terminal móvil 3,89 Vcc Cámara Cámara trasera de 50 Mpx + 0,08 Mpx Cámara delantera de 8 Mpx Saudações da realme mobile Mantenha pressionados os botões de ligar e aumentar o volume ao mesmo tempo até que a animação de inicialização do realme ser exibido para reiniciar o telefone. Como reiniciar o telefone How to Transfer Old Mobile Content to a New Mobile You can use realme Clone Phone to easily transfer photos, videos, music, contacts, messages, apps, etc from your old phone to the new one. 1. If you have an old Android phone, rst scan the QR code below, then download and install Clone Phone, next open Clone Phone on both the new and old phones, and follow the on-screen instructions to complete the operation. 2. If you have an old iPhone, open Clone Phone on the new phone directly, and follow on-screen instructions to sign in to iCloud account and sync the les. https://i.clonephone.coloros.com/download Mantenga presionados los botones de Encendido y Vol (+) hasta que aparezca la animación de inicio de realme para forzar el renicio del teléfono. Puede utilizar la función de realme "Clonar Teléfono" para transferir rápidamente sus fotos, vídeos, música, contactos y aplicaciones a su nuevo teléfono desde el antiguo. Para ello, siga estos pasos: 1. Si tiene un teléfono Android, primero escanee el código QR que aparece a continuación, segui…

Text truncated - open the document above for the full version.

Realme Chongqing Mobile Telecommunications Corp., Ltd. To: Federal Communications CommissionDate: 2023/04/10 7435 Oakland Mills Road Columbia, MD 21046 USA Attestation Section2.911(d)(5)(i)andSection2.911(d)(5)(ii) (KDB986446D01CoveredEquipment) Section2.911(d)(5)(i) Realme Chongqing Mobile Telecommunications Corp., Ltd.certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of theFCC rules. Section2.911(d)(5)(ii) Realme Chongqing Mobile Telecommunications Corp., Ltd.certifies that, as of the date of the filing of the application, the applicant is notidentified on the Covered List as an entity producing “covered” equipment. Type of Equipment subject to FCC Certification: Mobile Phone FCC ID:2AUYFRMX3760 If you have any questions, please feel free to contact me Contact Person:Yang LiangPing Position in the Company: Certification Manager Date of Signature:2023-04-10 ___________________________ Signatory (signature of the applicant)

realme U.S. Agent Designation for Service of Process TO:Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Innopeak Technology, Inc. FRN ： 0033456872 Contact Name: Richard Wahng Physical U.S. address: 2479 E Bayshore Rd #120, Palo Alto, CA 94303 Email: [email protected] This letter is to confirm that weInnopeak Technology, Inc.have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of theApplicantnoted below. U.S. Agent Signature: Date:February 15, 2023 Signed by (Printed Name/Title):Richard Wahng /General Counsel The applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Realme Chongqing Mobile Telecommunications Corp., Ltd. Grantee Code: 2AUYF Contact Name: LiangPing Yang Address: No.178 Yulong Avenue, Yufengshan, Yubei District, Chongqing, P.R. China. Email: [email protected] Applicant Signature: Date: February 15, 2023 Signed by (Printed Name/Title): LiangPing Yang / Compliance Manager

RealmeChongqingMobileTelecommunicationsCorp.,Ltd. Date: 2023-04-10 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern: The Realme Chongqing Mobile Telecommunications Corp., Ltd., the undersigned, hereby authorizesMiss.WendyZhanfromShenzhenMorlab Communications Technology Co., Ltd., to act on the behalf of the Realme Chongqing Mobile Telecommunications Corp., Ltd. solely in matters relatingtothe application for an FCC equipment authorization forFCC ID: 2AUYFRMX3760 including the signing of documents in connection with this Application. Necessary acts carried outShenzhen Morlab Communications Technology Co., Ltd.on our behalf of the Realme Chongqing Mobile Telecommunications Corp., Ltd.in connection with the Application shall have the same effect as acts of the Realme Chongqing Mobile Telecommunications Corp., Ltd.. Realme Chongqing Mobile Telecommunications Corp., Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thank you for your attention to this matter. Yours Sincerely, Signatory: Contact name:Liangping Yang Title:Certification Manager Tel:86 76986076999 Email:[email protected] Company name: Realme Chongqing Mobile Telecommunications Corp., Ltd.

RealmeChongqingMobileTelecommunicationsCorp.,Ltd. Date:2023-04-10 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: Request of Confidentiality forFCC ID: 2AUYFRMX3760 To Whom it may concern: Pursuant to sections 0.457 and 0.459 of Commission’s Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act,Realme Chongqing Mobile Telecommunications Corp., Ltd.hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-TermConfidentiality for 180 days after the grant as outlined in Public Notice DA04-1705. This provision will giveRealme Chongqing Mobile Telecommunications Corp., Ltd.temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listedas follows: PERMANENT AND SHORT-TERM CONFIDENTIAL LIST ExhibitDescription PERMANENT 1Block Diagram 2Operational Description 3Schematics 4BOM 5Tuneupprocedure SHORT-TERM 6External Photos 7Internal Photos 8Test-Setup Photos 9User Manual The Applicant understands that pursuantto Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory: Name:Liangping Yang Company name:Realme Chongqing Mobile Telecommunications Corp., Ltd. Address:No.178 Yulong Avenue, Yufengshan, Yubei District, Chongqing, China Tel: 86 76986076999 Email: [email protected]

Declaration To whom it may concern: We have declared below featured for FCC equipment authorization, Device FCC ID: 2AUYFRMX3760 Don't operate on Channels 12 and 13. US 2.4G channel 12-13 and Country code selection are disabled through proprietary software and are not user changeable Should you have any questions, please feel free to contact me. Signature : Date:2023/04/10 Contact name: Liangping Yang Title:Certification Manager Company name:Realme Chongqing Mobile Telecommunications Corp., Ltd.

Realme Chongqing Mobile Telecommunications Corp., Ltd. UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID:2AUYFRMX3760 (1) DFS Device -- Master,Client with Radar detection capability , Client without radar detection capability,N/A (2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 2412 –2462 MHzYes,NoYes,NoYes,NoYes,No 2422 –2452 MHzYes,NoYes,NoYes,NoYes,No 5745 –5825 MHzYes,NoYes,NoYes,NoYes,No 5755 –5795 MHzYes,NoYes,NoYes,NoYes,No 5180 –5240 MHzYes,NoYes,NoYes,NoYes,No 5190 –5230 MHzYes,NoYes,NoYes,NoYes,No 5260 –5320 MHzYes,NoYes,NoYes,NoYes,No 5270 –5310 MHzYes,NoYes,NoYes,NoYes,No 5500 –5700 MHzYes,NoYes,NoYes,NoYes,No 5510 – 5670 MHz Yes,NoYes,NoYes,NoYes,No (3) Country code selection ability -Yes ,No If no, pls explain how was implemented : Country is selected as US by defaultand user can not change the country code. (4) Meet 15.202 requirement - Yes ,No , pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply ,No Apply , (If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) The device configuration can not be modified by user as program is not exposed to user by any means. Hardware does not allow USB connection for user which is must to change the configuration. If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Printed Name : Liangping Yang Position : Certification Manager

FCC ID: 2AUYFRMX3760 External Photos 1. EUT front view 2. EUT rear view 3. EUT left side view 4. EUT right side view 5. EUT top view 6. EUT bottom view 7. Accessories

Label： Location： BackView

FCC ID: 2AUYFRMX3760 Internal Photos 1. EUT uncover view 2. Antenna view

MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Annex C Plots of System Performance Check Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.16 System Check_750MHz Communication System: UID 0, CW (0); Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750 Medium parameters used: f = 750 MHz; σ = 0.91 S/m; ε r = 42.306; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(10.43, 10.43, 10.43) @ 750 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) CW 750/Area Scan (81x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.31 W/kg CW 750/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 51.98 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 3.12 W/kg SAR(1 g) = 2.19 W/kg; SAR(10 g) = 1.42 W/kg Smallest distance from peaks to all points 3 dB below: Larger than measurement grid Ratio of SAR at M2 to SAR at M1 = 69% Maximum value of SAR (measured) = 2.30 W/kg 0 dB = 2.30 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.20 System Check_900MHz Communication System: UID 0, CW (0); Frequency: 900 MHz;Duty Cycle: 1:1 Medium: HSL_900 Medium parameters used: f = 900 MHz; σ = 0.976 S/m; ε r = 41.553; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(10.10, 10.10, 10.10) @ 900 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) CW900/Area Scan (71x71x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 3.24 W/kg CW900/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 55.19 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 3.85 W/kg SAR(1 g) = 2.78 W/kg; SAR(10 g) = 1.89 W/kg Smallest distance from peaks to all points 3 dB below = 16 mm Ratio of SAR at M2 to SAR at M1 = 66.3% Maximum value of SAR (measured) = 3.27 W/kg 0 dB = 3.27 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.27 System Check_1800MHz Communication System: UID 0, CW (0); Frequency: 1800 MHz;Duty Cycle: 1:1 Medium: HSL_1800 Medium parameters used: f = 1800 MHz; σ = 1.433 S/m; ε r = 40.277; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(8.60, 8.60, 8.60) @ 1800 MHz; Calibrated: 2022.03.21 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) CW1800/Area Scan (81x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 14.5 W/kg CW1800/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 87.77 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 18.2 W/kg SAR(1 g) = 10.18 W/kg; SAR(10 g) = 5.17 W/kg Smallest distance from peaks to all points 3 dB below = 11.2 mm Ratio of SAR at M2 to SAR at M1 = 56.2% Maximum value of SAR (measured) = 14.5 W/kg 0 dB = 14.5 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.28 System Check_2000MHz Communication System: UID 0, CW (0); Frequency: 2000 MHz;Duty Cycle: 1:1 Medium: HSL_2000 Medium parameters used: f = 2000 MHz; σ = 1.47 S/m; ε r = 40.219; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(8.27, 8.27, 8.27) @ 2000 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) CW2000/Area Scan (81x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 11.9 W/kg CW2000/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 91.90 V/m; Power Drift = -0.06 dB Peak SAR (extrapolated) = 19.1 W/kg SAR(1 g) = 10.55 W/kg; SAR(10 g) = 5.35 W/kg Smallest distance from peaks to all points 3 dB below = 11.2 mm Ratio of SAR at M2 to SAR at M1 = 55.6% Maximum value of SAR (measured) = 11.6 W/kg 0 dB = 11.6 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A…

Text truncated - open the document above for the full version.

MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Annex D Plots of Maximum SAR Test Results Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.20 GSM850_GPRS(4 TX slots)_Right Cheek_Ch189_Ant 2 Communication System: UID 0, GSM850(class 12) (0); Frequency: 836.4 MHz;Duty Cycle: 1:2.08 Medium: HSL_900 Medium parameters used: f = 836.4 MHz; σ = 0.943 S/m; ε r = 42.978; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(10.10, 10.10, 10.10) @ 836.4 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Ch189/Area Scan (71x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.604 W/kg Ch189/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 20.03 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 0.728 W/kg SAR(1 g) = 0.426 W/kg; SAR(10 g) = 0.276 W/kg Maximum value of SAR (measured) = 0.566 W/kg 0 dB = 0.566 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.28 GSM1900_GPRS(3 TX slots)_Right Tilt_Ch810_Ant 2 Communication System: UID 0, PCS1900(class 11) (0); Frequency: 1909.8 MHz;Duty Cycle: 1:2.77 Medium: HSL_2000 Medium parameters used: f = 1910 MHz; σ = 1.381 S/m; ε r = 39.997; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(8.27, 8.27, 8.27) @ 1909.8 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Ch810/Area Scan (71x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.05 W/kg Ch810/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 9.074 V/m; Power Drift = -0.05 dB Peak SAR (extrapolated) = 1.30 W/kg SAR(1 g) = 0.655 W/kg; SAR(10 g) = 0.302 W/kg Maximum value of SAR (measured) = 1.00 W/kg 0 dB = 1.00 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.28 WCDMA Band II_RMC 12.2Kbps_Right Tilt_Ch9400_Ant 2 Communication System: UID 0, UMTS-FDD (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium: HSL_2000 Medium parameters used: f = 1880 MHz; σ = 1.366 S/m; ε r = 40.167; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(8.60, 8.60, 8.60) @ 1880 MHz; Calibrated: 2022.03.21 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Ch9400/Area Scan (71x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.14 W/kg Ch9400/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 18.32 V/m; Power Drift = 0.10 dB Peak SAR (extrapolated) = 1.55 W/kg SAR(1 g) = 0.766 W/kg; SAR(10 g) = 0.348 W/kg Maximum value of SAR (measured) = 1.13 W/kg 0 dB = 1.13 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhen Morlab Communications Technology Co., Ltd. Date: 2023.03.27 WCDMA Band IV_RMC 12.2Kbps_Right Tilt_Ch1513_Ant 2 Communication System: UID 0, UMTS-FDD (0); Frequency: 1752.6 MHz;Duty Cycle: 1:1 Medium: HSL_1800 Medium parameters used: f = 1753 MHz; σ = 1.454 S/m; ε r = 39.5; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7624; ConvF(8.6, 8.6, 8.6) @ 1752.6 MHz; Calibrated: 2022.03.31 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn480; Calibrated: 2022.06.22 - Phantom: SAM 2; Type: QD000P40CC; Serial: TP:1464 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Ch1513/Area Scan (71x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.15 W/kg Ch1513/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 14.58 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 1.48 W/kg SAR(1 g) = 0.744 W/kg; SAR(10 g) = 0.350 W/kg Maximum value of SAR (measured) = 1.17 W/kg 0 dB = 1.17 W/kg MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Test Laboratory: Shenzhe…

Text truncated - open the document above for the full version.

MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ23030174S01 Annex E Conducted Power Note: Conducted power unit: dBm The target power was recorded in the manufacture document. 128189251128189251 824.2836.4848.8824.2836.4848.8 32.6032.6432.6133.5023.6023.6423.6124.50 32.6332.6732.6333.5023.6323.6723.6324.50 30.5630.6030.5531.5024.5624.6024.5525.500.05 28.7428.7828.7530.0024.4824.5224.4925.740.04 27.4227.4627.4329.0024.4224.4624.4326.000.04 27.7827.8927.8529.0018.7818.8918.8520.000.11 26.5426.6726.6527.5020.5420.6720.6521.500.13 24.4924.6324.5925.0020.2320.3720.3320.740.14 22.1722.2822.2422.5019.1719.2819.2419.500.11 Max.32.67Max.24.60 512661810512661810 1850.218801909.81850.218801909.8 29.5229.8129.8030.5020.5220.8120.8021.50 29.5629.8529.8230.5020.5620.8520.8221.50 27.4827.5927.5428.5021.4821.5921.5422.500.11 26.0026.0726.0227.5021.7421.8121.7623.240.07 24.1024.1224.1825.5021.1021.1221.1822.500.08 28.8228.5528.5629.0019.8219.5519.5620.000.27 28.6628.5128.2129.0022.6622.5122.2123.000.45 25.3224.8424.9325.5021.0620.5820.6721.240.48 23.6523.5823.2323.8020.6520.5820.2320.800.42 Max.29.85Max.22.66 926294009538131214131513413241824233 966298009938153716381738435744074458 1852.418801907.61712.41732.61752.6826.4836.4846.6 3GPP Rel 99RMC 12.2Kbps23.1123.1823.1224.0023.0923.1323.0824.0023.4523.4823.4624.50 3GPP Rel 6HSDPA Subtest-122.0222.1022.0223.0022.1022.1022.2623.0022.3422.2422.1323.50 3GPP Rel 6HSDPA Subtest-221.9122.0222.0023.0022.1122.1422.2323.0022.3522.2522.1523.50 3GPP Rel 6HSDPA Subtest-321.9121.9321.9223.0022.0322.0922.1823.0022.2722.2122.1123.50 3GPP Rel 6HSDPA Subtest-421.9121.9321.9223.0022.0422.1022.1923.0022.3122.2922.1223.50 3GPP Rel 8DC-HSDPA Subtest-122.1122.1722.0823.0022.1422.2122.0923.0022.5322.3422.2723.50 3GPP Rel 8DC-HSDPA Subtest-222.1522.1422.0623.0022.1822.2722.1423.0022.5922.3822.3423.50 3GPP Rel 8DC-HSDPA Subtest-322.1022.1422.0423.0022.1922.2522.1423.0022.5222.3322.2723.50 3GPP Rel 8DC-HSDPA Subtest-422.1222.1622.0523.0022.2122.2722.1623.0022.5322.3422.2823.50 3GPP Rel 6HSUPA Subtest-121.4821.2521.5423.0021.6821.9321.9223.0021.9421.6721.5023.50 3GPP Rel 6HSUPA Subtest-221.0720.9921.1422.0021.1721.3821.3122.0020.5420.4120.4022.50 3GPP Rel 6HSUPA Subtest-321.0521.1621.0922.0021.6721.8921.8522.0020.5220.6120.4922.50 3GPP Rel 6HSUPA Subtest-421.7621.8421.7523.0021.7221.5321.8823.0021.9921.7521.5623.50 3GPP Rel 6HSUPA Subtest-522.8623.0522.9724.0022.6022.8422.7424.0023.3523.3623.1724.50 3GPP Rel 7 HSPA+ (16QAM) Subtest-122.8822.6822.7424.0022.8923.0322.9724.0023.3123.3423.1624.50 Cable Loss0.8Cable Loss0.8Cable Loss0.6 Max.23.18Max.23.13Max.23.48 Tune-up Limit (dBm) Mode Attenuator Tune…

Text truncated - open the document above for the full version.