2AUYFRMX5056Mobile Phone

RMX5056 This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Regulations: Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. FCC Note: RF Exposure Information (SAR) This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the separation of 15 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR in formation on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2AUYFRMX5000 For this device, the highest reported SAR value for usage against the head is 1.17 W/kg, for usage near the body is 1.00 W/kg. While there may be dierences between the SAR levels of various phones and at various positions, they all meet the government requirements. SAR compliance for body-worn operation is based on a separation distance of 15 mm between the unit and the human body. Carry this device at least 15 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body-worn operation, choose the belt clips or hol sters, which do not contain metallic components, to maintain a separation of 15 mm between this device and your body. RF exposure compliance with any body-worn accessory, which contains metal, was not tested and certified, and use such body-worn accessory should be avoided. Regulatory Steps to search E-label : Go to Settings -About device - regulatory. This guide briey show you how to use the phone and its important functions. For more and detailed information of the phone and user guidance, please visit: www.realme.com/eu/support. Greetings from realme mobile Warning Do not place the phone or battery near or inside heating equipment, cooking equipments, high pressure vessels (such as microwave ovens, induction cooker, electric oven, heater, pressure cooker, water heater, gas stove, etc.) to prevent the battery overheating which may lead to an explosion. Back cover can’t be removed. The original charger, data cable and battery shall be used. Unapproved chargers, data cables, or batteries that are not certied by the manufacturer may result in electric shock, re, explosion, or other hazards. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with temperature ranging from 5 °C~35°C. How to reboot the phone Press and hold the Power Button and Volume Up Button at the same time until the realme boot animation is displayed to reboot the phone. How to Transfer Old Mobile Content to a New Mobile You can use realme Clone Phone to easily transfer photos, videos, music, contacts, messages, apps, etc from your old phone to the new one. 1. If you have an old Android phone, rst scan the QR code below, then download and install Clone Phone, next open Clone Phone on both the new and old phones, and follow the on-screen instructions to complete the operation. 2. If you have an old iPhone, open Clone Phone on the new phone directly, and follow on-screen instructions to sign in to iCloud account and sync the les. Standard accessories 1 Phone, 1 Charger, 1 USB data cable, 1 Safety Guide, 1 Quick Guide, 1 SIM Ejector Tool, 1 Protective Case. https://i.clonephone.coloros.com/download Благодарим за выбор смартфона realme realme В данном руководстве пользователя описаны наиб…

Text truncated - open the document above for the full version.

U.S. Agent Designation for Service of Process TO: Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Innopeak Technology, Inc. FRN: 0033456872 Contact Name: Richard Wahng Physical U.S. address: 2479 E Bayshore Rd #120, Palo Alto, CA 94303 Email: [email protected] This letter is to confirm that we Innopeak Technology, Inc. have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: September 18, 2024 Signed by (Printed Name/Title): Richard Wahng / General Counsel The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission- rel ated proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Realme Chongqing Mobile Telecommunications Corp., Ltd. Grantee Code: 2AUYF FRN: 0028939957 Contact Name: Mega Huang Address: No.178 Yulong Avenue, Yufengshan Yubei District, Chongqing, China. Email: [email protected] Applicant Signature: Date: September 18, 2024 Signed by (Printed Name/Title): Mega Huang/Manager realme

Realme Chongqing Mobile Telecommunications Corp., Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: December 05, 2024 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, Realme Chongqing Mobile Telecommunications Corp., Ltd. certifies that the equipment FCC ID: 2AUYFRMX5056 for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Realme Chongqing Mobile Telecommunications Corp., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, ________________________ Name: Mega Huang E-mail: [email protected]

Realme Chongqing Mobile Telecommunications Corp., Ltd. Date: December 05, 2024 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AUYFRMX5056 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Parts List Operational Description Tune Up software security requirement The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for a period of 180days: External Photos, Internal Photos, Test Setup Photos User Manual Sincerely, (signature) Contact Person: Mega Huang E-mail: [email protected]

RF_160, Issue 04 Realme Chongqing Mobile Telecommunications Corp., Ltd. Declaration of Authorization We Name: Realme Chongqing Mobile Telecommunications Corp., Ltd. Address: No.178 Yulong Avenue, Yufengshan Yubei District City: Chongqing Country: China Declare that: Name Representative of agent: Sherlock Fang Agent Company name: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Address: No.1 Workshop, M-10, Middle Section, Science & Technology Park City: Shenzhen Country: China is authorized to apply for Certification of the following product(s): Product description: Mobile phone Type designation: RMX5056 Trademark: realme FCC ID: 2AUYFRMX5056 on our behalf. Sincerely yours, Contact Person: Mega Huang Applicant: Realme Chongqing Mobile Telecommunications Corp., Ltd. Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 5 Appendix External Photos for SZCR2410003917WM SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 5 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 5

E-Label 1. The information that will be displayed on the e-label and information that will remain in the user manual is shown below: Information on E-label In Manual FCC ID number Yes No 15.19 statement (“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”) Yes Yes Class A / B Digital Device user manual statements* No Yes Caution to the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment1 No Yes Describe any other FCC regulatory information included in e-label* * If the e-label includes information typically included in the manual then the e-label shall clearly differentiate between information required to be on the device’s surface and information required to be in the manual – refer to KDB 784748 D02 e labelling v02r01. E-label show： B. Access to the required information on the e-label 1.Users are able to access the information in no more than three steps in a device’s menu. The actual steps are: To access the e-label information, in the device, Choose 1: Settings > About device > Regulatory, No special access codes or permissions are required to go through the above steps beyond enter- ing a userdefined password to protect against unauthorized access to the device. 2.The information is stored on the device, no special accessories or supplemental plug-ins (e.g., a SIM/USIM card) are required to access the information. Yes 3. Users are provided specific instructions on how to access the information. The information to the user is provided in the iPhone Info document. C. Labeling for Importation and Purchasing 1. Products utilizing e-labels are required to have a physical label on the product at the time of importation, marketing and sales. For devices imported in bulk and not packaged individually, a removable adhesive label or, for devices in protective bags, a label on the bags is acceptable for this purpose. Any removable label shall be of a type intended to survive normal shipping and handling and must only be removed by the customer after purchase. For devices imported already in individual packages ready for sale, the information may alternatively be provided on the package. It shall contain: 1.The FCC ID and/or the SDoC logo (if applicable); and 2.Any other information required by specific rule to be provided on the surface of the product unless such information is permitted to be included in the User’s manual or other packaging inserts. The FCC ID and Model number are present on the product packaging、physical label. D. Other considerations 1. The above information must be programmed by the responsible party and the information must be secured in such a manner that third-parties cannot modify it. The e-label information is pre-programmed by the grantee. The user cannot modify the e-label information. 2. All the applicable regulatory information required on the packaging or user instructions must be provided according to the rules even if it is displayed electronically. For example, hearing aid compatibility (HAC) ratings for the phones as specified in 47 C.F.R. § 20.19. Yes, it is provided

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 7 Appendix Internal Photos for SZCR2410003917WM SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 7 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 5 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 7 of 7 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR241000391707 Page: 1 of 34 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2410003917WM Applicant: Realme Chongqing Mobile Telecommunications Corp., Ltd. Address of Applicant: No.178 Yulong Avenue, Yufengshan, Yubei District, Chongqing, China Manufacturer: Realme Chongqing Mobile Telecommunications Corp., Ltd. Address of Manufacturer: No.178 Yulong Avenue, Yufengshan, Yubei District, Chongqing, China Equipment Under Test (EUT): EUT Name: Mobile Phone Model No.: RMX5056 Trade Mark: realme FCC ID: 2AUYFRMX5056 Standard(s) : 47 CFR Part 15, Subpart B Date of Receipt: 2024-10-23 Date of Test: 2024-11-02 to 2024-11-05 Date of Issue: 2024-12-10 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR241000391707 Page: 2 of 34 Revision Record Version Chapter Date Modifier Remark 01 2024-12-10 Original Authorized for issue by: Sherlock Fang/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR241000391707 Page: 3 of 34 2 Test Summary Emission Part Item Standard Method Requirement Result Conducted Emissions at Mains Terminals (150kHz-30MHz) 47 CFR Part 15, Subpart B ANSI C63.4:2014 15.107(a);Class B Pass Radiated Emissions (30MHz-1GHz) ANSI C63.4:2014 15.109(a);Class B Pass Radiated Emissions (Above 1GHz) ANSI C63.4:2014 15.109(g);Class B Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR241000391707 Page: 4 of 34 3 Contents Page 1 Cover Page ......................................................................................................................................... 1 2 Test Summary ..................................................................................................................................... 3 3 Contents ............................................................................................................................................. 4 4 General Information............................................................................................................................ 5 4.1 Details of E.U.T. ........................................................................................................................... 5 4.2 Description of Support Units ......................................................................................................... 5 4.3 Test modes .................................................................................................................................. 5 4.4 Measurement Uncertainty ............................................................................................................ 6 4.5 Test Location ............................................................................................................................... 7 4.6 Test Facility .................................................................................................................................. 7 4.7 Deviation from Standards ............................................................................................................. 7 4.8 Abnormalities from Standard Conditions ....................................................................................... 7 5 Equipment List ................................................................................................................................... 8 6 Emission Test Results ......................................................................................................................10 6.1 Conducted Emissions at Mains Terminals (150kHz-30MHz) ........................................................10 6.1.1 E.U.T. Operation .....................................................................................................................10 6.1.2 Test Mode Description ............................................................................................................10 6.1.3 Test Setup Diagram ................................................................................................................11 6.1.4 Measurement Procedure and Data .........................................................................................11 6.2 Radiated Emissions (30MHz-1GHz) ............................................................................................18 6.2.1 E.U.T. Operation .....................................................................................................................18 6.2.2 Test Mode Description ............................................................................................................18 6.2.3 Test Setup Diagram ................................................................................................................19 6.2.4 Measurement Procedure and Data .........................................................................................19 6.3 Radiated Emissions (Above 1GHz)..............................................................................................26 6.3.1 E.U.T. Operation .....................................................................................................................26 6.3.2 Test Mode Description ............................................................................................................26 6.3.3 Test Setup Diagram ................................................................................................................27 6.3.4 Measurement Procedure and Data .........................................................................................27 7 Test Setup Photo ...............................................................................................................................34 8 EUT Constructi…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 1 of 13 Appendix Test Setup Photos for SZCR2410003917WM SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 2 of 13 Test Setup Photo for WWAN Radiated Spurious Emissions Below 1GHz 9K-30MHz 30M-1GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 3 of 13 Radiated Spurious Emissions Above 1GHz 1G-18GHz 18G-40GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 4 of 13 Test Setup Photo for part 15B Conducted Emissions at Mains Terminals (150kHz-30MHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 5 of 13 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 6 of 13 Radiated Emissions (30MHz-1GHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 7 of 13 Radiated Emissions (Above 1GHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 8 of 13 Test Setup Photo for WLAN Conducted Emissions at AC Power Line (150kHz-30MHz) Radiated Emissions (Below 1GHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 9 of 13 Radiated Emissions (Above 1GHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 10 of 13 Radiated Emissions which fall in the restricted bands SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 11 of 13 DFS SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 12 of 13 Test Setup Photo for NFC Conducted Emissions at Mains Terminals (150kHz-30MHz) Emission Mask SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 13 of 13 Radiated Emissions (9kHz-30MHz) Radiated Emissions (30MHz-1GHz) - End of the Appendix -