2AV2O-ITS-AXX-XXVehicle detection radar sensor

(Model: ITS-AX3-4) User Manual Anti-fall Type Vehicle Detection Sensor 1 Please carefully read this manual before installation Thank you for purchasing our barrier anti-smash- ing radar product. To ensure that the radar can perform at its best, please read this user manual carefully and install and operate strictly according to the manual. The copyright of this product's hardware and software design is protected by law and shall not be infringed by any unit or individual. In order to further improve the quality and performance, the specifications and design of this product may be changed without prior notice. Please understand. 1.Introduction...................................... 2.Technical Specifications................ 3.Features.............................................. 4.Installation Instructions.................. 5.Cable interface Definition............. 6.Configuration Instructions............. 7.Precautions......................................... 8.Common problems......................... 9.Packing list.......................................... Content 2 3 4 6 8 9 5 16 18 18 1.Introduction 3 The Vehicle detection radar for the gate is developed for the management needs of entrance and exit management such as parking lots and underground garages. It can accurately control the rise and fall of the gate bar by working in coordination with the gate machine main control board. At the same time, it can effectively prevent the gate bar from "accidentally injuring" the target passing through the radar field of view, realizing intelligent anti-smashing. The radar adopts a highly integrated RF chip SoC solution, which has the chara cteristics of small size, low cost, all-day and all-weather operation, high detection sensitivity, high accuracy, simple debugging and installation, and stable and reliable. The operating frequency of this radar is 60-64GHz, using a linear frequency modulation continuous waveform and a distance resolution of up to 4cm. The millimeter wave antenna adopts a multi-tra nsmit and multi-receive method, with high angular resolution and angle measurement accuracy. Through the joint optimization design of software and hardware, this product can accurately identify and distinguish pedestrians, vehicles and other targets pa ssing through the gate bar area, avoiding phenomena such as "smashing ca rs", "smashing people", and "not falling bars". 2.Technical Specifications 4 FeatureParameterTechnical indicators System Properties Detect Range Upgrade & debug Operating Voltage Power Protect level Communication interface Operating temperature Shell Size Detection width Detection distance Online debug Online upgrade 485；Bluetooth 485；Bluetooth Application Straight boom barrier 1-6m(Default 3m) The default setting is ±0.5 meters, and can be customized within ±1.5 meters according to actual conditions. RS485；Bluetooth IP55 < 0.5W 9-24V (12V/1A) -40°C～+85°C 107.6*73.3*18.3mm 3.Features 5 Figure 1. Appearance and dimensions of Vehicle detection sensor The appearance of the radar is shown in Figure 1. Its main features are: LED indicator： There are two LED indicators on the front of the sensor. The red one is the power light, which stays on after the power is turned on; the green one is the status light, which turns on when a target is detected in the area and turns off when the target disappears； Configuration parameter saving: Can automatically save the detection area and other configurations, and use the most recently saved configuration parameters after power failure and restart; Firmware upgrade: No need to disassemble and install, upgrade the firmware online through 485/Bluetooth interface, and restart the sensor after the upgrade is completed to take effect; Stable performance: The sensor operation is not affected by external environment such as light, dust, rain and snow. Detection area configuration: The default sensing area of the sensor is 3 meters forward, and different detection areas can be set through the mobile phone app or computer debugging software; 4.Installation Instructions 6 The sensor should be installed on the surface of barrier gate box and vertically to the ground. The installation must follow the below steps: Step 1: Confirm the radar installation hole position The inner side of the straight rod is 200-300mm away from the radar installation hole position, 650-750mm from the lane ground (not the safety island) (for cars and vans), 750-800mm (for trucks with chassis higher than 700mm); the installation position is shown in Figure 2. Figure 2. Schematic diagram of the installation location of the sensor Step 2: Installation hole Use an electric drill to drill a fixing hole suitable for M16 at the selected position of the gate box. The recom- mended hole drill bit diameter is 18mm. 7 Step 3: Installation and Fixing Figure 3 Gate radar installation effect diagram As shown in the figure below, the radar is fixed to the gate box through the bottom bolts (torque value is less than 20N.m). First, insert the radar into the gate box, then cover it with a gasket and tighten it with an M16 screw, then insert the wiring harness end downward into the radar and tighten the metal buckle. The final installation effect is shown in Figure 3. 5.Cable interface definition 8 NoCable IDColorDescription 12V GND B-/RX A+/TX NO1 NO1 Red Black White Gray Blue Green Positive Negative 485 485A+ Normally open1 Normally open1 B- 1 2 3 4 5 NC2BrownNormally Close27 NC2PurpleNormally Close28 6 Gate control signal 485 line connection The wiring harness functions and connection relationships are as follows: Power connection The red wire "12V" is connected to the positive output terminal of the 12V power supply; The black wire "GND" is connected to the negative output terminal of the 12V power supply. The green and blue wires are relay normally open signals, connecting the ground sensor coil terminal and the common terminal (not distinguishing between positive and negative) of the gate cont…

Text truncated - open the document above for the full version.

Company Name: Changsha Microbrain Intelligent Technology Co., Ltd. Add: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China Tel: 0731-89909918 Fax: N/A E-mail: [email protected] Signature: Printed Name: Lu Tan Title: Senior Certificate DECLARATION Date: 2024/07/08 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 We, Changsha Microbrain Intelligent Technology Co., Ltd. hereby declare that product name: Vehicle detection radar sensor (FCC ID: 2AV2O-ITS-AXX-XX, model name: ITS-AX3-4, ITS-AXX-XX) are electrically identical with the PCB design, components and electromagnetic compatibility characteristics, and model: ITS-AX3-4 has been tested by Bay Area Compliance Laboratories Corp.(Dongguan). The differences of them are as follows: The model name and the enclosure Please contact me if there is need for any additional clarification or information.

Signature: Print Name: Lu Tan Title: Senior Certificate Company Name : Changsha Microbrain Intelligent Technology Co., Ltd. Add: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China Tel: 0731-89909918 Fax: N/A E-mail: [email protected] Authorization 'DWH7 10 FEDERAL COMMUNICATIONS COMMI SSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 7RZKRPLWPD\FRQFHUQ Our product: Vehicle detection radar sensorModel number: ITS-AX3-4, ITS-AXX-XX )&&,'2AV2O-ITS-AXX-XX, for marketing purpose, this product only supports BLE 1M (2402~2480MHz) and Radar (60~64GHz) the other functions, bands and modes were disabled to use by manufactu reU in the software, the end user has no capability to activate it. Sincerely Yours,

Company: Changsha Microbrain Intelligent Technology Co., Ltd Add: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China Tel: 0731-89909918 Fax: N/A E-mail: [email protected] CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 07/10/2024 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: 2AV2O-ITS-AXX-XX Changsha Microbrain Intelligent Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Changsha Microbrain Intelligent Technology Co., Ltd (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Print Name: Lu Tan Title: Senior Certificate

U.S. AGENT LETTER OF ATTESTATION Date: 2024-08-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AV2O-ITS-AXX-XX Changsha Microbrain Intelligent Technology Co., Ltd certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Changsha Microbrain Intelligent Technology Co., Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Ap plicant: Changsha Microbrain Intelligent Technology Co., Ltd Address:3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China FRN: 0029376712 Tel: 0731-89909918 Email: [email protected] Signed by (printed name):Tan lu Signature:

QA-FR-170-B Company: Changsha Microbrain Intelligent Technology Co., Ltd Add: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China Tel: 0731-89909918 Fax: N/A E-mail: [email protected] FCC Authorization Date: 2024-07-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Changsha Microbrain Intelligent Technology Co., Ltd, Hereby authorizes Bay Area Compliance Laboratories Corp.(Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp.(Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely, Signature: Print Name: Lu Tan Title: Senior Certificate

QA-FR-171-A Company: Changsha Microbrain Intelligent Technology Co., Ltd Add: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China Tel: 0731-89909918 Fax: N/A E-mail: [email protected] FCC Confidential Authorization Date: 2024/07/10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AV2O-ITS-AXX-XX In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (Changsha Microbrain Intelligent Technology Co., Ltd) hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Print Name: Lu Tan Title: Senior Certificate

Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-EXP Page 1 / 5 EUT EXTERNAL PHOTOS Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-EXP Page 2 / 5 Model: ITS-AX3-4 Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-EXP Page 3 / 5 Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-EXP Page 4 / 5 Model: ITS-AXX-XX Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-EXP Page 5 / 5

Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 1 / 8 EUT INTERNAL PHOTOS Model: ITS-AX3-4 Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 2 / 8 Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 3 / 8 Bluetooth Antenna Radar Chip Radar Antenna TX ANT RX ANT Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 4 / 8 Model: ITS-AXX-XX Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 5 / 8 Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 6 / 8 Buletooth Chip+ Antenna Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 7 / 8 Radar Chip Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-INP Page 8 / 8 Radar Antenna

MAXIMUM PERMISSIBLE EXPOSURE EVALUATION REPORT Applicant: Changsha Microbrain Intelligent Technology Co., Ltd. Address: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China P r o d u c t N a m e : Vehicle detection radar sensor F C C I D : 2AV2O-ITS-AXX-XX Standard(s): 47 CFR §1.1310, 47 CFR §2.1091, 47 CFR §15.255(g) Report Number: 2402V64080E-RF-00D Report Date: 2024/12/4 The above device has been tested and found compliant with the requirement of the relative standards by Bay Area Compliance Laboratories Corp. (Dongguan). Reviewed By: Pedro Yun Approved By: Gavin Xu Title: Project Engineer Title: RF Supervisor Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: The information marked ▲ is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with ★.This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. Each test item follows the test standard(s) without deviation. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: 2402V64080E-RF-00D Report Template Version: FCC §2.1091-V1.0 Page 2 of 5 GENERAL INFORMATION General Description Of Equipment under Test EUT Name: Vehicle detection radar sensor EUT Model: ITS-AX3-4 Multiple Models: ITS-AXX-XX Rated Input Voltage: DC 9-24V (Typical DC 12V) Serial Number: 2O5W-1 EUT Received Date: 2024/7/9 EUT Received Status: Good Note: The multiple models are electrically identical with the test model. The difference is only the enclosure. Please refer to the declaration letter for more detail, which was provided by manufacturer. Radio Parameters▲ Radio Frequency (MHz) Conducted output power including Tune-up Tolerance (dBm) Antenna Gain (dBi) EIRP including Tune-up Tolerance (dBm) BLE 2402-2480 -2.0 1.83-0.17 Radar 60000-64000 -6.0 12.0 6.0 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: 2402V64080E-RF-00D Report Template Version: FCC §2.1091-V1.0 Page 3 of 5 RF EXPOSURE EVALUATION (MPE) RF Exposure Evaluation Applicable Standard According to subpart 15.247(i) ,15.255(g)and subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculation formula Prediction of power density at the distance of the applicable MPE limit S = PG/4R² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); For simultaneously transmit system, the calculated power density should comply with: Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: 2402V64080E-RF-00D Report Template Version: FCC §2.1091-V1.0 Page 4 of 5 Calculated Data: Operation Modes Frequency (MHz) Antenna Gain Conducted output power including Tune-up Tolerance Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric)(dBm)(mW) BLE 2402-2480 1.83 1.52 -2 0.63 20.00 0.0002 1.0 Radar 60000-64000 12 15.85 -6 0.25 20.00 0.0008 1.0 Simultaneous transmission: BLE and Radar can transmit simultaneously: =S BLE /S limit- BLE + S Radar /S limit-Radar =0.0002/1.0+0.0008/1.0 =0.001 < 1.0 Result: Compliant. The device compliant RF Exposure at 20cm distances. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: 2402V64080E-RF-00D Report Template Version: FCC §2.1091-V1.0 Page 5 of 5 EXHIBIT A - EUT PHOTOGRAPHS Please refer to the attachment 2402V64080E-RF-EXP EUT EXTERNAL PHOTOGRAPHS and 2402V64080E-RF-INP EUT INTERNAL PHOTOGRAPHS. ***** END OF REPORT *****

1、Supplier ZhuHai JieLi Technology Co.,Ltd Address: 3rd Floor, Block A, Chentai Science and Technology Park, No. 56 Wanglong Road, Yuelu District, Changsha City 2. Antenna detail Size Antenna Size 3. Antenna S parameter The Bluetooth antenna operates at 2402-2480MHz and resonates in this band. The following table shows the main parameters of the antenna. Antenna S parameter 4、Antenna radiation performances： Frequency Gain (dBi) Test Efficiency (%) 2400MHz 1.73 40 2420MHz 1.78 38 2440MHz 1.79 38 2460MHz 1.79 38 2480MHz 1.79 38 2500MHz 1.83 38 Frequency (MHz) 2400-2500MHz Impedance 50 0hm Nominal Return Loss -19.2 dB Max Radiation Omni-Directional Gain (Peak) 1.83dBi 5. Antenna Simulation radiation Pattern Radiation pattern of 2.4GHz Radiation pattern of 2.45GHz Radiation pattern of 2.50GHz 6. Antenna test 3D Radiation Pattern (Free Space)

TEST REPORT Applicant: Changsha Microbrain Intelligent Technology Co., Ltd. Address: 3th Floor, Building A, Chentai Science Park, Wanglong Road No.56, Yuelu District, Changsha, China P r o d u c t N a m e : Vehicle detection radar sensor F C C I D : 2AV2O-ITS-AXX-XX Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2020 KDB 558074 D01 15.247 Meas Guidance v05r02 Report Number: 2402V64080E-RF-00A Report Date: 2024/12/6 The above device has been tested and found compliant with the requirement of the relative standards by Bay Area Compliance Laboratories Corp. (Dongguan). Reviewed By: Pedro Yun Approved By: Gavin Xu Title: Project Engineer Title: RF Supervisor Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: The information marked ▲ is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with ★.This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. Each test item follows the test standard(s) without deviation. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.:2402V64080E-RF-00A Report Template Version: FCC-BLE-V2.0 Page 2 of 46 CONTENTS DOCUMENT REVISION HISTORY ································································ 4 1. GENERAL INFORMATION ······································································· 5 1.1 GENERAL DESCRIPTION OF EQUIPMENT UNDER TEST ················································ 5 1.2 ACCESSORY INFORMATION ················································································· 5 1.3 ANTENNA INFORMATION DETAIL▲ ······································································ 5 1.4 EQUIPMENT MODIFICATIONS ·············································································· 5 2. SUMMARY OF TEST RESULTS ································································· 6 3. DESCRIPTION OF TEST CONFIGURATION ················································ 7 3.1 OPERATION FREQUENCY DETAIL ········································································· 7 3.2 EUT OPERATION CONDITION ·············································································· 7 3.3 SUPPORT EQUIPMENT LIST AND DETAILS ······························································· 7 3.4 SUPPORT CABLE LIST AND DETAILS ······································································ 7 3.5 BLOCK DIAGRAM OF TEST SETUP ········································································· 8 3.6 TEST FACILITY ······························································································ 10 3.7 MEASUREMENT UNCERTAINTY ·········································································· 10 4. REQUIREMENTS AND TEST PROCEDURES ············································· 11 4.1 AC LINE CONDUCTED EMISSIONS ······································································· 11 4.1.1 Applicable Standard ······························································································ 11 4.1.2 EUT Setup·········································································································· 12 4.1.3 EMI Test Receiver Setup ························································································· 12 4.1.4 Test Procedure ····································································································· 13 4.1.5 Corrected Result& Margin Calculation ········································································ 13 4.1.6 Test Result ········································································································· 13 4.2 RADIATION SPURIOUS EMISSIONS ······································································· 14 4.2.1 Applicable Standard ······························································································ 14 4.2.2 EUT Setup·········································································································· 14 4.2.3EMI Test Receiver & Spectrum Analyzer Setup ······························································· 16 4.2.4 Test Procedure ····································································································· 16 4.2.5 Corrected Result & Margin Calculation ········································································ 16 4.2.6 Test Result ········································································································· 16 4.3 MINIMUM 6 DB BANDWIDTH ············································································· 17 4.3.1 Applicable Standard ······························································································ 17 4.3.2 EUT Setup·········································································································· 17 4.3.3 Test Procedure ····································································································· 17 4.3.4 Test Result ········································································································· 17 4.4 MAXIMUM CONDUCTED OUTPUT POWER ····························································· 18 4.4.1 Applicable Standard ········································································…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-00A-TSP TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-00A-TSP Radiated Emission 9k-30MHz Parallel View Radiated Emission 9k-30MHz Perpendicular View Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-00A-TSP Radiated Emission 9k-30MHz Ground-parallel View Radiated Emission 30M-1GHz View Bay Area Compliance Laboratories Corp. (Dongguan) EXHIBIT No.: 2402V64080E-RF-00A-TSP Radiated Emission 1-18GHz View Radiated Emission 18-25GHz View