2AVEACE-P43-7005Monitor

Public View Monitor Manual CE-M8XXXXXXXXXX CE-M10XXXXXXXXXX CE-P10XXXXXXXXXX CE-P13XXXXXXXXXX CE-M16XXXXXXXXXX CE-M21XXXXXXXXXX CE-P21XXXXXXXXXX CE-M24XXXXXXXXXX CE-27XXXXXXXXXX CE-M27XXXXXXXXXX CE-M32XXXXXXXXXX CE-P32XXXXXXXXXX CE-M43XXXXXXXXXX CE-P43XXXXXXXXXX for models: Disclaimer: Clinton Electronics Corporation makes no representations or warranties, either expressed or implied, with respect to the contents of this document. Clinton Electronics Corporation reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. Check clintonelectronics.com for the most current model specifications. For additional technical support visit support.clintonelectronics.com II IMPORTANT SAFEGUARDS Federal Communications Commission Statement (FCC) This Class A device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense. The user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution To assure continued compliance, any changes or modifications not expressly approved by Clinton Electronics for compliance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Warning: Operation of this equipment in a residential environment could cause radio interference. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. A shielded-type power cord is required in order meet FCC emission limits and also to prevent interference to the nearby radio and television reception, It is essential that only the supplied power cord be used. 2. Use only shielded cables to connect I/O devices to this equipment. 3. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. ENG III IMPORTANT SAFEGUARDS Safety Warnings • Read all of these instructions. • Save these instructions for later use. • Follow all warnings and instructions marked on the monitor. • If provided with a 3-pin attachment plug on the power cord, (either from a supplied power cord or from external power supply) plug the cord into a grounded (earthed) 3-pin outlet. If you are unable to insert the plug into the outlet, contact a qualified electrician to replace the outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter or by breaking the grounding pin off. The grounding pin is an important safety feature. • This monitor should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to use, consult the products specifications online or check with qualified service person. • Do not overload wall outlets, power strips and/or extension cords as this can result in fire or electric shock. • Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. • When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that has the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. • The monitor shall be connected to ITE product with Limited Power Source(LPS) Output approved by Underwriters Laboratories (UL OR TUV) • Do not attempt to service this monitor yourself since opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. • Upon completion of any service or repairs to this monitor, ask the service technician to perform routine safety checks to determine that the monitor is in safe operating condition. The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of imp…

Text truncated - open the document above for the full version.

Covered list attestation FCC application letter Kiwa Page 1 of 2 RF_755_03 06-06-2024 [PLACE COMPANY LOGO HERE OR PUT ON COMPANY LETTERHEAD] Certification Application Attestation Statements VITA ELECTRONICS CO LTD 0029052990 5th FI 103 Chou Tze St Neihu District 114 Taipei, Taiwan Subject: FCC ID: 2AVEACE-P43-7005 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) VITA ELECTRONICS CO LTD certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> VITA ELECTRONICS CO LTD certifies that, the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered list installed on the device, nor will it be installed by the applicant anytime after certification. Statement for 47 CFR section 2.911(d)(5)(ii) [Insert Company Name Here] (“the applicant”) certifies that, as of the date of the filing of this application, the applicant - is / - is not (3) identified on the Covered List as an entity producing “covered” equipment. Date: 06/16/2026 City: 5th FI 103 Chou Tze St Neihu District Name (2) : Jack Tseng Function: Electrical Safety Engineer Telephone number: 02-26595977 Email address: [email protected] Signature: 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . (2): For FCC it must be the Grantee Code “owner” or the authorized agent. (3): double click on the appropriate box and select ‘’checked” then “OK” Covered list attestation FCC application letter Kiwa Page 2 of 2 RF_755_03 06-06-2024 [PLACE COMPANY LOGO HERE OR PUT ON COMPANY LETTERHEAD] Revision Record Sheet: Revision Section number Page number Date Remark(s) issued by 01 07-02-2023 1 st version RvM 02 1 15-02-2023 Changed Applicant to Company and added “Subject: FCC ID: “ RvdM 03 1 06-06-2024 FRN added at certification application and included [Insert Company Name Here] for the statements RvdM Issued/modified by : Richard van de Meer Function : Certification assessor Revision : 03 Date : 06-06-2024 Verified by : Willem Jan Jong Function : Team Lead Date : 06-06-2024 Released by : Axel Gase Function : Manager Quality Assurance Date of release: : 06-06-2024

RF_160_06 Declaration of Authorisation Date of issue 13-08-2025 (On manufacturer’s company letter heading) Declaration of Authorization We Name: VITA ELECTRONICS CO LTD Address: 5th FI 103 Chou Tze St Neihu District City: Taipei. Country: Taiwan. Declare that: Name Representative of agent: Jack Chang. (1) Agent Company name: TÜ V SÜ D Asia Ltd., Taiwan Branch. Address: No.31, Dinghu Rd.,.. City: Taoyuan City.. Country Taiwan (R.O.C.). is authorized to apply for Certification of the following product(s): Product description: Monitor. Type designation: CE-P43E-B / CE-P43XXXXXXXXXX. Trademark: clintonelectronics. Validity/ expiry date on our behalf. Date: .. City: Taipei.. Name: Jack Tseng.. (2) Function: Electrical Safety Engineer............................... Signature: 06/16/2026. Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent. Revision Record Sheet: Revision Section number Page number Date Remark(s) issued by 05 1 02-01-2023 History sheet added AG 06 all 13-08-2025 Kiwa logo change AG Issued/modified by : Axel Gase Function : Manager Quality Assurance Revision : 06 Date : 13-08-2025 Verified by : Willem Jan Jong Function : Team Lead Date : 13-08-2025 Released by : Axel Gase Function : Manager Quality Assurance Date of release: : 13-08-2025

FCC, Request for non-disclosure Date: 18-08-2025 RF_501, Issue 12 Page 1 of 2 Company Name: VITA ELECTRONICS CO LTD Address: 5th FI 103 Chou Tze St Neihu District City: Taipei Country: Taiwan To: Kiwa Netherlands B.V., Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Request for confidentiality FCC ID: 2AVEACE-P43-7005 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Date: 06/16/2026 Name and signature of applicant: Jack Tseng Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should state in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Kiwa NL B.V. at least 7 days before date of actual marketing or before expiration of the STC period FCC, Request for non-disclosure Date: 18-08-2025 RF_501, Issue 12 Page 2 of 2 Revision Record Sheet: Revision Section number Page number Date Remark(s) issued by 10 1 02-01-2023 History sheet added AG 11 1 & 2 23-06-2023 Corrected date and page# WJJ 12 all 18-08-2025 Kiwa logo change AG Issued/modified by : Axel Gase Function : Manager Quality Assurance Revision : 12 Date : 18-08-2025 Verified by : Willem Jan Jong Function : Team Lead Date : 18-08-2025 Released by : Axel Gase Function : Manager Quality Assurance Date of release: : 18-08-2025

Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 1 of 8 Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 2 of 8 Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 3 of 8 Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 4 of 8 External Ant Connecter Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 5 of 8 ANT Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 6 of 8 Label Location Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 7 of 8 Appendix EP Photographs of EUT Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 8 of 8

Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 1 of 3 Label Location Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 2 of 3 Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name: clintonelectronics Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 3 of 3

Appendix EP Photographs of EUT Brand Name: clintonelectronics Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 1 of 4 Appendix EP Photographs of EUT Brand Name: clintonelectronics Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 2 of 4 Appendix EP Photographs of EUT Brand Name: clintonelectronics Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 3 of 4 RF module Appendix EP Photographs of EUT Brand Name: clintonelectronics Product: TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Type Identification: CE-P43E-B / CE-P43XXXXXXXXXX Page 4 of 4 RF IC ANT

TÜ V SÜ D Asia Ltd., Taiwan Branch 7F., No. 37, Sec. 2, Zhongyang S. Rd., Beitou District, Taipei City, 11270, Taiwan (R.O.C.) Phone: + 886 2 2898-6818 Fax: + 886 2 2895-1598 Revision: 1.0 Effective: 2024-06-07 Page 1 of 9 RF Exposure Evaluation Applicant : VITA ELECTRONICS LTD Product : TFT LCD COLOR MONITOR PUBLIC VIEW MONITOR Brand : clintonelectronics Model : CE-P43E-B / CE-P43XXXXXXXXXX FCC ID : 2AVEACE-P43-7005 In accordance with FCC rule Part §1.1310 RESPONSIBLE FOR NAME SIGNATURE DATE Approved By Jack Chang 2025.10.14 Prepared By Ariel Hsu 2025.10.14 Signatures in this approval box have checked this document in line with the requirements of TÜ V SÜ D Product Service control rules. EXECUTIVE SUMMARY TÜ V SÜ D Asia Ltd., reports apply only to the specific samples tested under stated test conditions. Construction of the actual test samples has been documented. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. The manufacturer/importer is responsible to the Competent Authorities for any modifications made to the production units which result in non-compliance to the relevant regulations. TÜ V SÜ D Asia Ltd. shall have no liability for any deductions, inferences or generalizations drawn by the client or others from TÜ V SÜD Asia Ltd. issued reports. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. Page 2 of 9 Contents 1 General Information ....................................................................................................................3 1.1 Report Modification Record ...........................................................................................................3 1.2 Introduction ....................................................................................................................................3 1.3 Applied Standard ...........................................................................................................................4 1.4 Deviation from standards ..............................................................................................................4 1.5 Reference Test Report ..................................................................................................................4 2 General EUT Information ............................................................................................................5 2.1 Technical Specification of EUT .....................................................................................................5 2.2 Antenna List ..................................................................................................................................7 2.3 Variation of family model(s) ...........................................................................................................7 3 FCC Maximum Permissible Exposure Evaluation ...................................................................8 3.1 Introduction ....................................................................................................................................8 3.2 Reference Levels ..........................................................................................................................8 3.3 Classification of the Assessment Methods....................................................................................9 3.4 Power Density Calculation (Worst Case) ......................................................................................9 Page 3 of 9 1 General Information 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. History of this test report Issue Description of Change Date of Issue 1 Initial Issue 2025-10-14 1.2 Introduction The information contained in this report is intended to show verification of RF qualification approval. The testing requirements of the standards for the tests listed in Section 1.5. Applicant : VITA ELECTRONICS LTD Address : 5F., No. 103, Chou Tze St., Neihu Dist., Taipei City 114, Taiwan (R.O.C.) Manufacturer : VITA ELECTRONICS LTD Brand Name : clintonelectronics Product Name : TFT LCD COLOR MONITOR PUBLIC VIEW MONITOR Model Number(s) : CE-P43E-B / CE-P43XXXXXXXXXX Date of Receipt of EUT : 2025-06-30 Start of Test : 2025-09-02 Finish of Test : 2025-09-17 Test Laboratory : TÜ V SÜ D Asia Ltd., Taiwan Branch Address : 7F., No. 37, Sec. 2, Zhongyang S. Rd., Beitou District, Taipei City 11270, R.O.C. Taiwan Test Location : TÜ V SÜ D Asia Ltd., Taiwan Branch, Guishan Laboratory Address : No. 31, Dinghu Road, Guishan District, Taoyuan City, TAIWAN (R.O.C.) The test facility is accredited by TAF (member of ILAC), under number 2573 according to ISO/IEC 17025: 2017. FCC Designation Number No.: TW2573 Page 4 of 9 1.3 Applied Standard FCC rule Part §2.1091 FCC Part §1.1310 FCC KDB 447498 D04 Interim General RF Exposure Guidance v01 OET Bulletin 65 1.4 Deviation from standards None 1.5 Reference Test Report Test Lab TÜ V SÜ D Asia Ltd., Taiwan Branch Report Number 6128625036401, 6128625036601 Page 5 of 9 2 General EUT Information All information in this chapter was provided by the applicant. 2.1 Technical Specification of EUT WLAN 2.4G Items EUT information Operating Frequency 2412 ~ 2462 MHz Channel number 802.11b/g/n HT20: 11 Maximum Output Power (dBm) 802.11b: 20.35 dBm 802.11g: 24.08 dBm 802.11n HT20:23.94 dBm Operation Voltage 24V.0dc From Adapter Modulation DSSS (DBPSK, DQPSK, CCK) OFDM (BPSK, QPSK, 16QAM, 64QAM) Test Software Version Ampak RFTestTool, VER: 6.0 Sample ID Radiated Sample: 718873488-E1-003 Conducted Sample: 718873488-E1-004 Page 6 of 9 WLAN 5G Items EUT information Operating Frequency Band 1: 5180 MHz to 5240 MHz Band 2a: 5260 M…

Text truncated - open the document above for the full version.

無線2.4-2.5G 5G 5.8G 4.9-5.9G天線的4dBi全向高增益天線 2.4GHz 5G

TÜ V SÜ D Asia Ltd., Taiwan Branch 7F., No. 37, Sec. 2, Zhongyang S. Rd., Beitou District, Taipei City, 11270, Taiwan (R.O.C.) Phone: + 886 2 2898-6818 Fax: + 886 2 2895-1598 Revision: 1.0 Effective: 2024-06-07 Page 1 of 254 RF Test Report Report Number : 6128625036601 Applicant : VITA ELECTRONICS LTD Product : TFT LCD COLOR MONITOR PUBLIC VIEW MONITOR Brand : clintonelectronics Model : CE-P43E-B / CE-P43XXXXXXXXXX FCC ID : 2AVEACE-P43-7005 Applicable Standard: FCC rule Part §15.407 RESPONSIBLE FOR NAME SIGNATURE DATE Approved By Jack Chang 2025.10.14 Prepared By Ariel Hsu 2025.10.14 Signatures in this approval box have checked this document in line with the requirements of TÜ V SÜ D Product Service control rules. EXECUTIVE SUMMARY TÜ V SÜ D Asia Ltd., reports apply only to the specific samples tested under stated test conditions. Construction of the actual test samples has been documented. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. The manufacturer/importer is responsible to the Competent Authorities for any modifications made to the production units which result in non-compliance to the relevant regulations. TÜ V SÜ D Asia Ltd. shall have no liability for any deductions, inferences or generalizations drawn by the client or others from TÜ V SÜD Asia Ltd. issued reports. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. Report Number: 6128625036601 Page 2 of 254 Contents 1 General Information ....................................................................................................................3 1.1 Report Modification Record ...........................................................................................................3 1.2 Introduction ....................................................................................................................................3 1.3 Reference Measurement Document .............................................................................................4 1.4 Summary of Test Results ..............................................................................................................4 2 General EUT Information ............................................................................................................5 2.1 Technical Specification of EUT .....................................................................................................5 2.2 Antenna List ..................................................................................................................................6 2.3 Variation of family model(s) ...........................................................................................................6 3 EUT Setup Configuration ...........................................................................................................7 3.1 Block Diagram ...............................................................................................................................7 3.2 Support Equipment ........................................................................................................................9 3.3 Support Cable(s) ...........................................................................................................................9 3.4 Channel list and Power Setting .................................................................................................. 10 3.5 Test Configuration ...................................................................................................................... 12 3.6 Test Condition ............................................................................................................................ 13 4 Technical Requirements .......................................................................................................... 14 4.1 Duty Cycle .................................................................................................................................. 14 4.2 Maximum Conducted Output Power .......................................................................................... 15 4.3 Bandwidth Measurement ........................................................................................................... 17 4.4 Maximum Power Spectral Density ............................................................................................. 19 4.5 Frequency Stability ..................................................................................................................... 20 4.6 Radiated Spurious Emissions and Band Edges ........................................................................ 22 4.7 AC Power Line Conducted Emission Measurement .................................................................. 26 5 Measurement Uncertainty ....................................................................................................... 27 Appendix A. Test Equipment ................................................................................................................... 28 Appendix B. Duty Cycle ............................................................................................................................ 29 Appendix C. Maximum Conducted Output Power ................................................................................. 33 Appendix D. Bandwidth Measurement ................................................................................................... 45 Appendix E. Maximum Power Spectral Density ..................................................................................... 53 Appendix F. Frequency Stability ............................................................................................................. 61 Appe…

Text truncated - open the document above for the full version.

Report Number: 6128625036601 Page 29 of 254 Appendix B. Duty Cycle 802.11a *Duty cycle = 1 *If duty cycle of test signal is ≥ 98%, duty factor is not required. *If duty cycle of test signal is < 98%, duty factor shall be considered. 6Mbps Duty On (ms): - Duty Cycle = Ton / (Ton + Toff) Duty OnOff (ms): - Duty Cycle (%): 100 VBW (Hz): 10 Report Number: 6128625036601 Page 30 of 254 802.11ac20 *Duty cycle = 1 *If duty cycle of test signal is ≥ 98%, duty factor is not required. *If duty cycle of test signal is < 98%, duty factor shall be considered. MCS0 Duty On (ms): - Duty Cycle = Ton / (Ton + Toff) Duty OnOff (ms): - Duty Cycle (%): 100 VBW (Hz): 10 Report Number: 6128625036601 Page 31 of 254 802.11ac40 *Duty cycle = 0.666ms/1.695ms = 0.95827 *If duty cycle of test signal is ≥ 98%, duty factor is not required. *If duty cycle of test signal is < 98%, duty factor shall be considered MCS0 Duty On (ms): 0.666 Duty Cycle = Ton / (Ton + Toff) Duty OnOff (ms): 0.695 Duty Cycle (%): 95.827 VBW (Hz): 2k Report Number: 6128625036601 Page 32 of 254 802.11ac80 *Duty cycle = 0.338ms/0.371ms = 0.91105 *If duty cycle of test signal is ≥ 98%, duty factor is not required. *If duty cycle of test signal is < 98%, duty factor shall be considered MCS0 Duty On (ms): 0.338 Duty Cycle = Ton / (Ton + Toff) Duty OnOff (ms): 0.371 Duty Cycle (%): 91.105 VBW (Hz): 3k Report Number: 6128625036601 Page 33 of 254 Appendix C. Maximum Conducted Output Power Maximum Output Power (Band 1) <11a> Channel Channel Frequency Maximum Output Power Power Setting Limit (dBm) (MHz) (dBm) (mW) 36 5180 12.94 19.678863 32 24 40 5200 12.71 18.663797 32 24 48 5240 13.59 22.855988 32 24 <11n20> Channel Channel Frequency Maximum Output Power Power Setting Limit (dBm) (MHz) (dBm) (mW) 36 5180 12.51 17.823788 32 24 40 5200 12.81 19.098533 32 24 48 5240 13.65 23.173946 32 24 Report Number: 6128625036601 Page 34 of 254 Maximum Output Power (Band 1) <11n40 > Channel Channel Frequency Maximum Output Power Power Setting Limit (dBm) (MHz) (dBm) (mW) 38 5190 10.61 11.508004 12 24 46 5230 11.08 12.823306 12 24 <11ac20 > Channel Channel Frequency Maximum Output Power Power Setting Limit (dBm) (MHz) (dBm) (mW) 36 5180 12.53 17.906059 32 24 40 5200 12.85 19.275249 32 24 48 5240 13.71 23.496328 32…

Text truncated - open the document above for the full version.