2AVEB-ISB13Bluetooth speaker

Product Name：Bluetooth speaker Model：ISB13 Function description 1.(MODE )Press to change source modes to blue tooth, USB, or micro SD/TF 2. ( △play button) Press to play or pause music tracks. Press and hold for 3s to disconnect blue tooth device and enter pairing mode. 3. (-button) Press to decrease volume level. Press and hold to play the previous track. 4. (+button) Press to increase volume level. Press and hold to play the next track. 5.(Light button) Press repeatedly to cycle through LED light settings. Press and hold for 5s to turn voice prompts on/off. 6. (TF card port) supports TFCARD/Micro SDCARD and can play music in the card. 7. (USB port) supports USB and can play music in USB. 8. (DC 5V) when the DC 5V cable is plugged in, the LED lights up. (Bluetooth connection) -When powered on, the speaker will enter blue tooth mode automatically. If you are playing from a different source, press the mode button to select blue tooth mode. -Open your device in BT mode, search for new devices and select ISB13. Refer to the manual for your specific device for instructions on pairing and connecting blue tooth devices. -After the device is successfully paired, a voice prompt will announce the connection. -Use the controls on the connected device to select and begin playing audio. Use the controls on the speaker or the connected device to play, pause, and adjust volume. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications t o this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SHENZHEN E-BESTA ENTERPRISES CO., LTD Agent Authorization Company: SHENZHEN E-BESTA ENTERPRISES CO., LTD Address: 11Floor, Building No. 87, the 1st Industrial Zone, Lisonglang Gongming Street, Guangming New District, Shenzhen, China Product Name: Bluetooth speaker Model Number(s): ISB13, EB-S1203 Product Description: Bluetooth speaker We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022.11.25 Name: Simon Meng Title: Manager Company: SHENZHEN E-BESTA ENTERPRISES CO., LTD

SHENZHEN E-BESTA ENTERPRISES CO., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: November 25, 2022 Subject; Request for Confidentiality FCC ID: 2AVEB-ISB13 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Simon Meng Title: Manager

SHENZHEN E-BESTA ENTERPRISES CO., LTD Model Difference Statement Dear Sir/Madam, Added modelsEB-S1203 basis of the original product ISB13. The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same Sincerely, Name: Simon Meng Title: Manager Company name: SHENZHEN E-BESTA ENTERPRISES CO., LTD Address: 11Floor, Building No. 87, the 1st Industrial Zone, Lisonglang Gongming Street, Guangming New District, Shenzhen, China

EUT PHOTO(External Photos) FCC ID: 2AVEB-ISB13

Page 1 of 1 Label and Information FCC Label Sample FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

EUT PHOTO(Internal Photos) FCC ID: 2AVEB-ISB13 BT:ANT ※※※※※ END OF REPORT ※※※※※

FCC ID: 2AVEB-ISB13 RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06 and part 2.1093， Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. For BR+EDR Max Conducted Power(dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 0.96 0(±1) 1 1.259 2402 5 0.390249 3.0 So a SAR test is not required

Report No: SSP22110054A Antenna Test Report Page 1 of 4 Antenna Test Report Test Standard: IEEE 149-1979 Manufacturer: SHENZHEN E-BESTA ENTERPRISES CO., LTD Product Name: 2.4GHz Antenna Model: ISB13 Report No.: SSP22110054A Tested Date: 2022-11-03 Issued Date: 2022-11-05 Tested By: William Liu (Engineer) Approved By: Lahm Peng (Manager) Prepared By: Shenzhen ZRLK Testing Technology Co., Ltd. 1F, No. 35 Building, Changxing Technology Industrial Park, Yutang Street, Guangming New District, Shenzhen City, Guangdong Province, China Tel.: +86-755-33019599 Fax.: +86-755-33019599 Website: www.zrlklab.com Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen ZRLK Testing Technology Co., Ltd. Report No: SSP22110054A Antenna Test Report Page 2 of 4 1. General Information 1.1 Product Information Manufacturer Manufacturer: SHENZHEN E-BESTA ENTERPRISES CO., LTD Address of Manufacturer: 11Floor, Building No. 87, the 1st Industrial Zone, Lisonglang Gongming Street, Guangming New District, Shenzhen, China General Description of Antenna Product Name: 2.4GHz Antenna Model No.: ISB13 Frequency Range: 2400MHz-2483.5MHz Type of Antenna: PCBAntenna Antenna Gain: 0dBi (Max.) Impedance: 50 ohm Antenna View (15mm*1.6mm) 1.2 Test Methodology All measurements contained in this report were conducted with standards IEEE 149-1979 for IEEE Standard Test Procedures for Antennas. 1.3 Test Facilities Testing Lab: Shenzhen ZRLK Testing Technology Co., Ltd. All measurement facilities used to collect the measurement data are located at 1F, No. 35 Building, Changxing Technology Industrial Park, Yutang Street, Guangming New District, Shenzhen City, Guangdong Province, China Report No: SSP22110054A Antenna Test Report Page 3 of 4 2. OTA Test 2.1 Gain Frequency Peak Gain (dBi) Polarity 2402MHz 0 Horizontal 2402MHz -0.5 Vertical 2442MHz -0.8 Horizontal 2442MHz -1.1 Vertical 2480MHz -1.5 Horizontal 2480MHz -1.8 Vertical 2.2 Radiation Pattern View Report No: SSP22110054A Antenna Test Report Page 4 of 4

Project No.: ZKT-221115L8534E Page 1 of 73 FCC TEST REPORT FCC ID:2AVEB-ISB13 Report Number. ................................ : ZKT-221115L8534E Date of Test ......................................... November 12, 2022 to November 24, 2022 Date of issue ..................................... : November 29, 2022 Total number of pages ....................... 73 Test Result ...................................... : PASS Testing Laboratory. ........................ : Shenzhen ZKT Technology Co., Ltd. Address ........................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name ......................... : SHENZHEN E-BESTA ENTERPRISES CO., LTD Address ........................................... : 11Floor, Building No. 87, the 1st Industrial Zone, Lisonglang Gongming Street, Guangming New District, Shenzhen, China Manufacturer's name ................... : SHENZHEN E-BESTA ENTERPRISES CO., LTD Address ........................................... : 11Floor, Building No. 87, the 1st Industrial Zone, Lisonglang Gongming Street, Guangming New District, Shenzhen, China Test specification: Standard ........................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Test procedure ................................. : / Non-standard test method .............. : N/A Test Report Form No. .................... : TRF-EL-112_V0 Test Report Form(s) Originator .... : ZKT Testing Master TRF ................................... : Dated: 2021-07-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name ................................. : Bluetooth speaker Trademark ....................................... : ILIVE Model/Type reference ....................... : ISB13, EB-S1203 Ratings .............................................. : DC 3.7V by battery, USB 5V charging Project No.: ZKT-221115L8534E Page 2 of 73 Testing procedure and testing location: Testing Laboratory ..................................... :Shenzhen ZKT Technology Co., Ltd. Address ...................................................... :1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Jim Liu Tested by (name + signature) .................... : Jackson Fang Reviewer (name + signature) ..................... : Lake Xie Approved (name + signature) .................... : Project No.: ZKT-221115L8534E Page 3 of 73 Table of Contents Page 1. VERSION ............................................................... 5 2. TEST SUMMARY ........................................................ 6 2.1 TEST FACILITY ......................................................... 7 2.2 MEASUREMENT UNCERTAINTY ......................................... 7 3. GENERAL INFORMATION ................................................ 8 3.1 GENERAL DESCRIPTION OF EUT ........................................ 8 3.2 Test Setup Configuration .................................................. 9 3.3 Support Equipment ....................................................... 9 3.4 Test Mode ............................................................. 10 3.5 EQUIPMENTS LIST FOR ALL TEST ITEMS ................................ 11 4. EMC EMISSION TEST ................................................... 13 4.1 Conducted emissions .................................................... 13 4.1.1 POWER LINE CONDUCTED EMISSION Limits ........................... 13 4.1.2 TEST PROCEDURE ................................................... 13 4.1.3 DEVIATION FROM TEST STANDARD ................................... 13 4.1.4 TEST SETUP ......................................................... 13 4.1.5 EUT OPERATING CONDITIONS ........................................ 14 4.1.6 Test Result ........................................................... 15 4.2 Radiated emissions ..................................................... 17 4.2.1 Radiated Emission Limits ............................................... 17 4.2.2 TEST PROCEDURE ................................................... 17 4.2.3 DEVIATION FROM TEST STANDARD ................................... 18 4.2.4 TEST SETUP ......................................................... 18 4.2.5 EUT OPERATING CONDITIONS ........................................ 19 4.2.6 TEST RESULTS ...................................................... 20 5. RADIATED BAND EMISSION MEASUREMENT ............................ 28 5.1 Test Requirement: ...................................................... 28 5.2 TEST PROCEDURE .................................................... 28 5.3 DEVIATION FROM TEST STANDARD .................................... 29 5.4 TEST SETUP .......................................................... 29 5.5 EUT OPERATING CONDITIONS ......................................... 29 5.6 TEST RESULT ......................................................... 30 6. CONDUCTED BAND EDGE AND SPURIOUS EMISSION .................... 31 6.1 Limit ................................................................... 31 6.2 Test Setup ............................................................. 31 6.3 Test procedure ......................................................... 31 6.4 DEVIATION FROM STANDARD .......................................... 31 6.5 CSE Test Result ........................................................ 32 7. 20DB&99% BANDWIDTH ................................................ 43 7.1 Test Setup ............................................................. 43 7.2 Limit ......…

Text truncated - open the document above for the full version.

EUT TEST PHOTO FCC ID: 2AVEB-ISB13 Radiated band emission (30MHz-1GHz)： Conducted emission： Radiated band emission (Above 1GHz)：