2AVI6-UT-16WIRELESS CHARGER

FCC Statement ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help important announcement Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

JE DEVELOPMENT GROUPLIMITED FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Tel: +86- 13923797929 E-mail: [email protected] Series Models Description Date: 2020/01/04 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD FCC ID: 2AVI6-UT-16 Dear Sir/Madam, We, JE DEVELOPMENT GROUPLIMITED Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only color and model number is different for these model: Product name:WIRELESS CHARGER Model no.:UT-16, WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT-30 Sincerely, Name:JEWAY.SHEN Company:JE DEVELOPMENT GROUPLIMITED Address: FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Phone: +86- 13923797929 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: Jan. 04, 2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AVI6-UT-16UT-16, WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT- 30 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name:JEWAY.SHEN Company:JE DEVELOPMENT GROUPLIMITED Address: FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Phone: +86- 13923797929 Fax: N/A E-Mail: [email protected]

JE DEVELOPMENT GROUPLIMITED FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Tel: +86- 13923797929 E-mail: [email protected] Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2020-01-09 To whom it may concern: We, JE DEVELOPMENT GROUPLIMITED the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AVI6-UT-16 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name:JEWAY.SHEN Company:JE DEVELOPMENT GROUPLIMITED Address: FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Phone: +86- 13923797929 Fax: N/A E-Mail: [email protected]

FCC ID: 2AVI6-UT-16 FCC ID: 2AVI6-UT-16 FCC ID: 2AVI6-UT-16

FCC ID: 2AVI6-UT-16 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may caus e undesired operation.

FCC ID: 2AVI6-UT-16 Ant Coils FCC ID: 2AVI6-UT-16

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong TEST REPORT Report Reference No. ..................... : FCC ID. ............................................ : GTS20190903009-1-4-2 2AVI6-UT-16 Compiled by ( position+printed name+signature) .. : File administrators Jimmy Wang Supervised by ( position+printed name+signature) .. : Test Engineer Aaron Tan Approved by ( position+printed name+signature) .. : Manager Jason Hu Date of issue ..................................... : Dec. 18, 2019 Representative Laboratory Name .: Shenzhen Global Test Service Co., Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : JE DEVELOPMENT GROUPLIMITED Address ............................................ : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Test specification ...........................: Standard ........................................... : FCC Rules and Regulations part 2.1091 KDB680106 D01v03 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ....................................... : Dated 2014-12 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: WIRELESS CHARGER Trade Mark ....................................... : N/A Manufacturer .................................... : JE DEVELOPMENT GROUPLIMITED Model/Type reference....................... : UT-16 Listed Models .................................. : WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT-30 Modulation Type ............................... : ASK Operation Frequency ........................ : From 110KHz~205KHz Rating ............................................... : 12V2A Result................................................ : PASS Report No.: GTS20190903009-1-4-2 Page 2 of 12 T E S T R E P O R T Test Report No. : GTS20190903009-1-4-2 Dec. 18, 2019 ____________________________________________________________________________________ Date of issue Equipment under Test : WIRELESS CHARGER Model /Type : UT-16 Listed Models : WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT-30 Applicant : JE DEVELOPMENT GROUPLIMITED Address : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Manufacturer : JE DEVELOPMENT GROUPLIMITED Address : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Factory : SHEN ZHEN JEWAY TECHNOLOGY CO, LTD Address : C BUILDING YANBIAN XUEZIWEI INDUXTRY SHAJING CITY BAOAN DIS SHENZHEN, CHINA Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20190903009-1-4-2 Page 3 of 12 Contents 1 S U M M A R Y ............................................................................ 4 1.1 General Remarks 4 1.2 Product Description 4 1.3 Description of the test mode 4 1.4 Modifications 4 2 T E S T E N V I R O N M E N T .............................................................. 5 2.1 Address of the test laboratory 5 2.2 Test Facility 5 2.3 Environmental conditions 5 2.4 Summary of measurement results 6 2.5 Statement of the measurement uncertainty 6 2.6 Equipments Used during the Test 6 3 T E S T C O N D I T I O N S A N D R E S U L T S ............................................. 7 3.1 Applicable Standard 7 3.2 Limit 7 3.3 Test Setup 7 3.4 Measurement Procedure 8 3.5 Test Result of E and H field Strength 8 3.6 Simultaneous E-Filed Strength and H-Filed Strength 9 3.7 Equipment Approval Considerations 11 3.8 Conclusion 11 4 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 12 Report No.: GTS20190903009-1-4-2 Page 4 of 12 1 S U M M A R Y 1.1 General Remarks Date of receipt of test sample : Sep. 20, 2019 Testing commenced on : Dec. 17, 2019 Testing concluded on : Dec. 18, 2019 1.2 Product Description Product Name: WIRELESS CHARGER Model/Type reference: UT-16 Power supply: DC 12V from adapter Adapter information: Model: TEKA024-1202000UK Input: 100-240V~, 50/60Hz;0.7A MAX Output: 12V2A Wireless Charger Antenna Type Coil Antenna Antenna Gain 0.0dBi Operation frequency 110KHz~205KHz Modulation Type ASK 1.3 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Charging and communication mode Test Conditions Description TM1 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1(Battery Status: <1%) Pre-tested TM2 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1(Battery Status: <50%) Pre-tested TM3 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1(Battery Status: 100%) Pre-tested TM4 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 2(Battery Status: <1%) Pre-tested TM5 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 2(Battery Status: <50%) Pre-tested TM6 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 2(Battery Status: 100%) Pre-tested TM7 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 3(Battery Status: <1%) Pre-tested TM8 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 3(Battery Status: <50%) Pre-tested TM9 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 3(Battery Status: 100%) Pre-tested TM10 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1+ Mobile…

Text truncated - open the document above for the full version.

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong FCC PART 15 SUBPART C TEST REPORT Report Reference No. ..................... : FCC ID. ............................................ : GTS20190903009-1-4 2AVI6-UT-16 Compiled by ( position+printed name+signature) .. : File administrators Jimmy Wang Supervised by ( position+printed name+signature) .. : Test Engineer Aaron Tan Approved by ( position+printed name+signature) .. : Manager Jason Hu Date of issue ..................................... : Dec. 18, 2019 Representative Laboratory Name .: Shenzhen Global Test Service Co., Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : JE DEVELOPMENT GROUPLIMITED Address ............................................ : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Test specification ...........................: Standard ........................................... : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2013 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ....................................... : Dated 2014-12 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: WIRELESS CHARGER Trade Mark ....................................... : N/A Manufacturer .................................... : JE DEVELOPMENT GROUPLIMITED Model/Type reference....................... : UT-16 Listed Models .................................. : WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT-30 Modulation Type ............................... : ASK Operation Frequency ........................ : From 110KHz~205KHz Rating ............................................... : 12V2A Result................................................ : PASS Report No.: GTS20190903009-1-4 Page 2 of 23 T E S T R E P O R T Test Report No. : GTS20190903009-1-4 Dec. 18, 2019 ____________________________________________________________________________________ Date of issue Equipment under Test : WIRELESS CHARGER Model /Type : UT-16 Listed Models : WG-3B, UT-15, UT-22, UT-14, UT-21, UT-20, UT-30 Applicant : JE DEVELOPMENT GROUPLIMITED Address : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Manufacturer : JE DEVELOPMENT GROUPLIMITED Address : FLAT BO7 FLO023, HOVER INDUSTRIAL BUILDING, NO 26-38 KWAI CHEONG ROAD. N.T. HONG KONG Factory : SHEN ZHEN JEWAY TECHNOLOGY CO, LTD Address : C BUILDING YANBIAN XUEZIWEI INDUXTRY SHAJING CITY BAOAN DIS SHENZHEN, CHINA Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20190903009-1-4 Page 3 of 23 Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Description of the test mode 5 2.4 Modifications 5 3 T E S T E N V I R O N M E N T .............................................................. 6 3.1 Address of the test laboratory 6 3.2 Test Facility 6 3.3 Environmental conditions 6 3.4 Summary of measurement results 7 3.5 Statement of the measurement uncertainty 7 3.6 Equipments Used during the Test 7 4 T E S T C O N D I T I O N S A N D R E S U L T S ............................................. 9 4.1 AC Power Conducted Emission 9 4.2 Radiated Emission 12 4.3 Occupied Bandwidth 16 4.4 Antenna Requirement 17 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 18 6 PH O T O S O F T H E E U T ........................................................... 19 Report No.: GTS20190903009-1-4 Page 4 of 23 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 15 Subpart C (Section 15.207): Conducted limits. FCC Rules and Regulations Part 15 Subpart C (Section 15.209): Radiated emission limits; general requirements. ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices Report No.: GTS20190903009-1-4 Page 5 of 23 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Sep. 20, 2019 Testing commenced on : Dec. 17, 2019 Testing concluded on : Dec. 18, 2019 2.2 Product Description Product Name: WIRELESS CHARGER Model/Type reference: UT-16 Power supply: DC 12V from adapter Adapter information: Model: TEKA024-1202000UK Input: 100-240V~, 50/60Hz;0.7A MAX Output: 12V2A Wireless Charger Antenna Type Coil Antenna Antenna Gain 0.0dBi Operation frequency 110KHz~205KHz Modulation Type ASK 2.3 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Charging and communication mode Test Conditions Description TM1 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1 Pre-tested TM2 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 2 Pre-tested TM3 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 3 Pre-tested TM4 AC/DC Adapter (12V/2A) + EUT + Mobile Phone 1+ Mobile Phone 2 Pre-tested TM5 AC/DC Adapter (12V/2A) + EUT + Mobile…

Text truncated - open the document above for the full version.

FCC ID: 2AVI6-UT-16