2AVJL-S9360 Robot Vacuum Cleaner

After-sales Service Warranty period The warranty period for Rabat and accessories is 1 ye ar. For detailed information, please contactyour local authorized dealer. Warranty content Name Warranty content Warranty period Rabat Rabat (includes built-in lithium battery) 1 year Accessorles Charging deck; Power cord; Water tank 1 year Consumables Main brush, Side Brush, Main brush cover, Filter, / Main brush cleaning tools, Dust bin Note: consumables included have NOwarranty. Non-warranty regulations 1. Unauthorized repairs, misuses, collisions, negligence, accidents, modifications, im proper use of non-product accessories, etc., or tearing, altering stickers or anti-counterfeiting labels. 2. Beyond the warranty period. 3. Damage caused byforce majeure. 4. Does not meet the performance failures listed in the product performance fail u re ta ble. 5. Due to human reasons, this product and its accessories have performance problems listed in the product performance failure table. FCCWarning This equipment has been tested and found to complywith the limits fora Class B digital device, pursuantto part 15 ofthe FCC Rules. These li mits are designed to provide reasonable protection agai nst harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not insta l led and used in accordance with the instructions, may cause ha rmfu I interference to radio commu nications. However, there is no guarantee that interference will not occur in a particular Installation. lfthis equipment does cause harmful interference to radio or television reception, which can be determined by turni ng the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • lncrease the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radiofTV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authorityto operate this eq uipment. This device c ompl ies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 J This device may not cause harmful interference, and (2) this device must accept any interfer­ ence received, including interference that may cause undesired operation. T his equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in co njunction with any other antenna o r transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. -28- Warranty Card User's Information Name Tel. E-mail __________ _ Post/Zi p Code _______ _ Mdre�------------------------ Product Information Mode l ________________________ _ Co l or ________________________ _ Serial No. ______________________ _ Service Record Service Failure record information -29- Service Service technician date signature

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 9 External Photos for SZEM1912021136CR FCC ID: 2AVJL-S9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 9 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 8 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 9 of 9

Size Location

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 14 Internal Photos for SZEM1912021136CR FCC ID:2AVJL-S9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 14 1 EUT Constructional Details Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 8 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 9 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 10 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 11 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 12 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 13 of 14 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 14 of 14

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113602 Page: 1 of 7 Keny Xu EMC Laboratory Manager 1 Cover page RF Exposure Evaluation Report Application No.: SZEM1912021136CR Applicant: Beijing One More Hour Technology Co., Ltd. Address of Applicant: Room 701, 7th Floor, Bldg 2, 1st to 17th Floors, No.6 yard, No.102, Jiuxianqiao Road, Chaoyang Dist, Beijing, China Manufacturer: Shenzhen Silver Star Intelligent Technology Co., Ltd Address of Manufacturer: Building A1, Silver Star Hi-Tech Industrial Park, Guanguang Road, Guanlan Street , Longhua District, Shenzhen, Guangdong, China Factory: Shenzhen Silver Star Intelligent Technology Co., Ltd Address of Factory: Building A1, Silver Star Hi-Tech Industrial Park, Guanguang Road, Guanlan Street , Longhua District, Shenzhen, Guangdong, China Equipment Under Test (EUT): Product Name: 360 Robot vacuum cleaner Model No.: S9, S6 Pro, X90, S90, S91 ♣ ♣ ♣♣ ♣ Please refer to section 4.1 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: 2AVJL-S9 Standards: 47 CFR Part 1.1307 47 CFR Part 1.1310 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2019-12-11 Date of Test: 2019-12-13 to 2020-01-14 Date of Issue: 2020-01-16 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113602 Page: 2 of 7 2 Version Revision Record Version Chapter Date Modifier Remark 01 2020-01-16 Original Authorized for issue by: Bill Chen /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113602 Page: 3 of 7 3 Contents Page 1 COVER PAGE .............................................................................................................................................. 1 2 VERSION ...................................................................................................................................................... 2 3 CONTENTS .................................................................................................................................................. 3 4 GENERAL INFORMATION .......................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF EUT ................................................................................................................. 4 4.2 TEST LOCATION .......................................................................................................................................... 5 4.3 TEST FACILITY ............................................................................................................................................ 5 4.4 DEVIATION FROM STANDARDS ..................................................................................................................... 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS............................................................................................ 5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ................................................................................. 5 5 RF EXPOSURE EVALUATION .................................................................................................................... 6 5.1 RF EXPOSURE COMPLIANCE REQUIREMENT ................................................................................................ 6 5.1.1 Limits ................................................................................................................................................ 6 5.1.2 Test Procedure ................................................................................................................................ 6 4.1.3 EUT RF EXPOSURE EVALUATION ............................................................................................................... 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113602 Page: 4 of 7 4 General Information 4.1 General Description of EUT Power Supply: Adapter: Model: SK05T-2400200Z Input:AC 100-240V 50/60Hz 1.5A Output:DC 24V 2A Rechargeable battery DC 14.4V 5200mAh (Charger by adapter) Cable: DC cable:150cm(A magnetic) Operation Frequency: 802.11b/g/n(HT20): 2412MHz to 2462MHz Modulation Type: 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g/n: OFDM (64QAM, 16QAM, QPSK, BPSK) Number of Channels: 802.11b/g/n(HT20):11 Channel Spacing: 5MHz Antenna Type: FPC Antenna Antenna Gain: 1dBi Remark: Model No.: S9, S6 Pro, X90, S90, S91 Only the model S9 was tested, since the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model name. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113602 Page: 5 of 7 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G- …

Text truncated - open the document above for the full version.

I2C1 I2C0_SCL I2C0_SDA I2C0 VCCIO1 VCC_IO GPIO0_B4/I2C1_SCL GPIO0_B3/I2C1_SDA GPIO1_D1/UART1_TX/I2C0_SCL/SPI2_CSN0 GPIO1_D0/UART1_RX/I2C0_SDA/SPI2_CLK HYM8563 Read A3H Write A2H Reserve MPU6500 SN3236 P ortPin nameDomain Bus name Pull-up voltage Slave Device I2C2 I2C1_SCL I2C1_SDA GPIO2_A3/UART0_RTSN/SPI0_CSN0/I2C2_SCL GPIO2_A2/UART0_CTSN/SPI0_CLK/I2C2_SDA VCCIO2 S lave Addr (MS 7Bits) Note Slave Bus Capability I2C2_SCL I2C2_SDA APIO2_VDD VCCIO0 VCC_IO I2C MAP MIC Array Connector-Analog(Option)0x3C/0x3F VL6180 0X29(7bit) ST Proximity sensing module RTC CW2015/CW2013 Read 0XC5 Write 0XC4 Fuel Gauge(Option) AD0=0 0x68 AD0=1 0x69 RTL 8201F PA:XA8326 LDO 5 3.3V RK3308B AVDD_CODEC_3V3 WiFI Module VBAT Default Res erve LDO4 RK3308B VCCIO3 PowerDomain eMMC or FLASH Nand VCCQ 1.8V 3.3V Default 1.8V 3.3VDefault 300mA 300mA Res erve Def ault1.8V 1.8V Power Diagram and Sequence RK3 308B VCCIO2 PowerDomain RK3308B VCCIO4 PowerDomain 3.3V VDD_CORE VDD_LOGSlot:2 DCDC DCDC Slot:2 1.0V 1.0V DVFS 1.0V LDOVDD_1V0Slot:2 1.0V 1.0V 500 mA LDO 2 VCC _1V8 RK3308B PLL_AVDD_1V8 RK3308B SARADC_AVDD_1V8 RK3308B OTP_AVDD_1V8 RK3308B USB_AVDD_1V8 1A VCC_IO BUC K4 TF Card RK3 308B VCCIO0& VCCIO1& VCCIO5 PowerDomain RK3308B USB_AVDD_3V3 SPDIF OUT/IN Port LCM 3.3V Supply D DR3=1.5V DDR3L=1.35V DDR3=1.5V DDR3L=1.35V Power up Timing V CC_DDR Normal voltage Default voltage DCDC PowerNametimer Slot:2 5.0VDCDCVCC5V0_SYSSlot:1 5.0V RES ET BYPASS:RESET IC 300mA LDO 3 1.8 V VCCIO_WIFI Cha rger IC(PowerPath) Power Control 1A BUC K3 VCC _DDRRK3308B DDR PHY DDR Device Cur rent limiting IC 5V USB 0 OTG VCC 5V0_SYS 2 4V/1A Adapter 3A BUCK V CC_1V8 LDOSlot:2 1.8V 1.8V VCCIO_SDIO LDO(1.8V) or VCC_IO Slot:2 1.8V or 3.3V Slot:2 1.8V 1.8V or 3.3V LDO(1.8V) or VCC_IO VCCIO_FLASH 1.8V VCC_IO DCDCSlot:2 3.3V 3.3V 50mSReset VCCIO0 VCCIO3 VCCIO2 VCCIO1 VCCIO5 VCCIO4 Voltage 3 .3V Support Voltage 1 .8VIO PowerDomain 3.3V(Default) SDMMC 1.8V(Default) eMMC 3.3V(Default) PMUIO Support MOT ORx5 1.8 V(Default) WiFi(SDIO) Support Support Support 1.8V(Default) I2S0 3.3V(Default) LCDC Support Bat tery Option Option Option RK3308B CODEC_AVDD_1V8 Option Option RK3308B Logic VDD_LOG VDD_1V0RK3308B C/DPLL_DVDD_1V0,A/GPLL_DVDD_1V0 RK3308B USB_DVDD_1V0 2A BUC K1 VDD _CORE RK3308B ARM Core 1A Res erve BUCK2 Note:A ll the Power filter capacitors should be placed close to the power pins of RK3308B Trace>60mil(Max 1.5A) Trace>30mil(Max 0.5A) RK3308B Part-LRK3308B Part-N RK3308B Part-M A RM Logic RK3308B Part-A If share clk source with WiFi, Accuracy <= 10ppm. Otherwise <=20ppm for Independent crystal design O SC PLL N POR/WIFI_CLK Fix 1.8V RK3308B Part-K Power Filter Note:A ll the Power filter capacitors should be placed close to the power pins of RK3308B Not e: Reserver for RK3308G/H RK3308G/H: DDR2_VREF D DR RK3308B Part-E N AND FLASH/eMMC/SFC/SPI RK3308B Part-I U SB2.0 RK3308B Part-J S WITCH B AYX L L X=X0 Y=Y0 L H X=X1 Y=Y1 LH X=X2 Y=Y2 H H X=X3 Y=Y3 S ARADC OTP RK3308B Part-C H ardware ID0 U ART/SPI2/JTAG/I2C0 L CDC/I2S1_8CH/PDM_8CH/MAC RK3308B Part-F RK3308B Part-G S DMMC/UART2 S DIO U ART4 I2S0_2CH RK3 308B Part-B RK3308B Part-D Over t emperature protection T SADC Hardwa re ID1 Hardware ID2 SPDIF 1:VCCI O_FLASH=1.8V 0:VCCIO_FLASH=3.3V NOTE: PIN R3 Default as FLASH_SEL Function UART0/SPI0/I2C2 I2S0_8CH/PDM_8CH RK3308B Part-H A CODEC 2 4V DC IN Charger IC Battery 4cell POWER Control N ormal Charging:CHGOK=LOW Complete charge:CHKOK=HIGH Ic hg=200mV/RS1=200mV/(0.4||0.2)=1.5A Ttrickle=30Min*Ctmr/0.1uf=30Min Ttotal=3Hour*Ctmr/0.1uF=3Hour SL AVE ADDRESS READ A3H WRITE A2H RT C RTC POWER WX 7233M VIN<=30V,Vout=1.5V~12V,Iout=150mA SGM2200 VIN<=26.4V,Vout=1.5V~5V,Iout=50mA For ce Powerdown(Option) B5 819W VBR=40V DC Not DC Not Power ADCCASE 1.8V ~0.9V ~0.7V as ..DC=20K Vi n=4.5V~30V 3A VEN threshold=1.2V 5V BUCK 5. 1V/3A Vf b=0.6V + - + F B=0.6V De fault 1.04V E TA3409A/CS4175-E:1.0uH/2A SY8089AAAC:2.2uH/2A DD R3L 1.35V 150K DDR3 DDR Type VCC_DDR Voltage R2208 1.5V 150K R2210 100K 120K VCC_DDR VCC_1V8 Default 1.5V Layout Note:The power of VCC_1V8 must be according to star style to each load VDD_1V0VDD_LOG VCCIO_FLASH De fault 3.3V V CC_IO FLASH_SEL (Pin R3 of RK3308) 3.3V 1.8V eMMC Nand Flash 1.8V (Default) 3.3V VCCIO_FLASH H L H L Sleep:ARM=0.965V F B=0.6V RK 3308DCDC FB OUT VD D Feedback from RK3308 E TA3409A/CS4175-E:1.0uH/2A SY8089AAAC:2.2uH/2A De fault ARM=1.125V VDD_ARM VCC3V3_S0 VBAT_MOTOR + OT G POWER OTG HO ST use for U-Disk download fireware .if no use,remove all. OPTION US B OTG DET D+D- HSD1 O TG(Default) HSD2 UART S H L US B OTG/DEBUG UART connector OPTION OPTION Rem ind: Refer to the latest AVL for parts selection. DDR 3 1x16bit Nand Flash Remind : Refer to the latest AVL for parts selection. Note if use toshiba and sandisk DDR mode, VCCQ1 and VCCQ4 must be connected to VCCIO_FLASH els e 128MB SLC (Default) R4102 DNP 0R Type of Flash Layout Note:As soon as possible reduce the branch of FLASH_D0 Remind:Short two TP points to Enter MaskRom. Remind : Refer to the latest AVL for parts selection. SPI Nor Flash Layout Note:As soon as possible reduce the branch of FLASH_D4/SFC_CLK Remind:Short two TP points to Enter MaskRom. WIF I/BT Module-1T1R Module Power SP EAKER Class AB(Option) L IDAR COLLISION_DET_LIDAR 20190412 Itrip Itrip Vvprop i=5*Itrip*Rsense<=2.5V Vsense<=500mV Rated Current:Itrip<=Vsense/Rsense~=500mA + + FAN SWEEP MOTOR Ga in_MID=1+68K/10K=7.8 Rated Current=470+-94mA=564mA MID SWEEP MOTOR PCB Note: GND_OPA plane for OPA. separate from GND plane. PCB Note: GND_OPA plane for OPA. separate from GND plane. Gain=1+220K/10K=23 SID E SWEEP MOTOR Water Pump MOTOR 4. 5V~5.5V OPT ION Ra ted Current=2A Gain_SIDE=1+68K/10K=7.8 Rated Current=430mA SIDE_ADCmax=0.989V(R*G*430mA) Rated Current=500mA PUMP_ADCmax=1.15V(R*G*500mA) Gain=1+220K/10K=23 Current limit=VREF/10xRs=2.3A O PTION ST ALL CURRENT 1.38A STALL CURRENT=2A 20190408 20190412 Cu rrent limit=VREF/10xRs=1.3A 20 190415 - +OPA + OP A - - + OPA + OP A - COLLIS ION L DET Water Tank/Trainer/Drg DET GR…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113601 Page: 1 of 105 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM1912021136CR Applicant: Beijing One More Hour Technology Co., Ltd. Address of Applicant: Room 701, 7th Floor, Bldg 2, 1st to 17th Floors, No.6 yard, No.102, Jiuxianqiao Road, Chaoyang Dist, Beijing, China Manufacturer: Shenzhen Silver Star Intelligent Technology Co., Ltd Address of Manufacturer: Building A1, Silver Star Hi-Tech Industrial Park, Guanguang Road, Guanlan Street , Longhua District, Shenzhen, Guangdong, China Factory: Shenzhen Silver Star Intelligent Technology Co., Ltd Address of Factory: Building A1, Silver Star Hi-Tech Industrial Park, Guanguang Road, Guanlan Street , Longhua District, Shenzhen, Guangdong, China Equipment Under Test (EUT): EUT Name: 360 Robot vacuum cleaner Model No.: S9, S6 Pro, X90, S90, S91   Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: 2AVJL-S9 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2019-12-11 Date of Test: 2019-12-13 to 2020-01-14 Date of Issue: 2020-01-16 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113601 Page: 2 of 105 Revision Record Version Chapter Date Modifier Remark 01 2020-01-16 Original Authorized for issue by: Bill Chen /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113601 Page: 3 of 105 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.209 & 15.247(d) Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.209 & 15.247(d) Pass Remark: Model No.: S9, S6 Pro, X90, S90, S91 Only the model S9 was tested, since the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model name. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191202113601 Page: 4 of 105 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 3 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 7 4.4 TEST LOCATION .................................................................................................................................... 8 4.5 TEST FACILITY ...................................................................................................................................... 8 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 8 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 8 5 EQUIPMENT LIST ...................................................................................................................................... 9 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 12 6.1 ANTENNA REQUIREMENT .................................................................................................................... 12 6.1.1 Test Requirement: ....................................................................................................................... 12 6.1.2 Conclusion ................................................................................................................................... 12 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 13 7.1 MINIMUM 6DB BANDWIDTH .................................................................................................................. 13 7.1.1 E.U.T. Operation ..............................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM1912021136CR FCC ID: 2AVJL-S9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs 1.1 Radiated Emissions Test Setup Below 1GHz Above 1GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3