2AVJR-X8wireless charger pad

Instruction manual IH-Ql1102W Wireless Charger Pad Thanks for choosing us! Is a very special wireless charging pad, allowing you to charge your iPhone 8/iPhone X and Apple watch on one pad simultaneously, effectively and stably. It will bring you the exceptional fast wireless charging experiences and give you a genuine wireless living.It supports various mobile phones and electronic devices with wireless charging function under Qi standard.Before using the , please check this manual carefully and keep it well for backup checking. Product components Technical Speclflcatlons Madel: IH-Qll 102W lnpul: 9V/1.67A or 5V/2A Charging a「ea Output: 9V/1.1A or SV/1.SA Conversion Rale:s80% Weight :90g Size: 174mm(L)*88mmx(W)*9.Smm(H) P.S.: It applies only to Apple watch cha「gerwith 1 M or 0.3M long cable. IH-QI 1102W英文说明书 Apple watch charger with 0.3M long cable Silicone pad Apple Watch charger setup instructions lnslallaHon steps: USB port 1. Pis use original Apple watch charge「with 1 M or 0.3M long cable. 2. Open the back cove「fromthe OPEN sign 3. Embed the Apple watch charger first and then put the cable in the duct, after that, plug in the USB port. 4. Put the cable in order and make sure the cover can be closed smoothly. 5. Remove the sticker of the silicone pad and stick it on the backside of the embedded watch charger. Smartphone and Watch wireless charging simultaneously Smartphone wireless charging Smartphone wireless charging 1. When the power ,s connected, the led indicator flashes and then goes out, showing IH-QI 1102W in standby status. 2. When the charging device in put in place, Is in working status, the led indicator keeps on. 3. When the charging device is removed. the led indicator goes out, showing resumes to standby status 4. The led indicator will keep flashing or the charging pad will switch off by itself when charging goes wrong. Walch wireless charging Embed the watch wireless charger and power on, then the watch can be wirelessly charged. Safety In SfrucHons 1. Do not disassemble or throw into fire or water.to avoid causing a short ci「cuitleakage . 2. Do not use wireless charger in severely hot.humidor corrosive environments.to avoid circuit damage and occurs leakage phenomenon. 3. Do not place too close with magnetic stripe or chip card (IDcard,bank ca闪s,etc.)toavoid magnetic fa缸e. 4. Please keep the distance at least 20cm between implantable medical devicesotential interference with the medical device. 5.To take care of the children.to ensure that they won't play the wireless charger as a toy.to avoid unnecessary accidents. Notes 1. Please use qualified AC adopter. The AC odopte「should be 9V 1.67 A or QC2.0 or above, otherwise insufficient input eleclric current might cause unstable charging. 2. Do not place too close with magnetic stripe or chip card (IDcard,bank cards,etc.)to avoid magnetic failure. 3. Make sure the plate doesn't get too hot. If the plate is too worm, take your phone aft the plate, and switch the plate off. The plate may switch off automatically if it is too hot. when the plate has cooled down, try charging again. FAQ and Solution 1. Why the led lndlcato『keepflashing and my phone do not receive any cha『ge? - - Please make sure your mobile device is Qi-standard supported. - - Make sure you find the right charging position - - Make SU「eyou use an qualified AC adapte「 --Please make sure you use 9V /1.67 A or QC2.0 or above AC adapter. 2.Why II charges slowly than my original adapter came with the mobile device? --The wi「eless charging current size allowed by the phone itself or external receiver coil is different. - -When the phone is charging. the standby power consumption is large, so it is recommended to reduce the phone standby program 3.ls radiation from wireless charging harmful to one's heath? The wireless charger emits non-ionizing radiation which is not harmful to humans. 4从ydevice Is hot while charging, Is II normal? If you don't cha「geyou「devicein a good cha「gmgarea, the heat dissipation may not good and it will cause your phone hot during charging. Is has overheat protection function. 5.Walch not charged? Watch wireless charger is not setup correctly or product failure, pis contact with afte「 - sales Warranty We provide all our customers 12 months warranty from the date of purchase. FCCWarnlng This device complies with part 15 of the FCC Rules. Operation is sub」ectto the following two conditions: (l) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause 归mfulinterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the 「eceiveris cannected -Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC RF exposure statement The equipment complies with …

Text truncated - open the document above for the full version.

Shenzhen Funxim Innovation Technology Co., Ltd Statement Product Name: wireless charger pad Model N o.: IH-QI1102W, X8, X9, S8 We(Shenzhen Funxim Innovation Technology Co., Ltd, Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China.) hereby state that all models above are identical in interior structure, electrical circuits and components, and just the model names are different for marking requirement. Signature: Name / title: Xueshouzhen / general manager Tel: 0755-23025697 Email: [email protected] Date: 2020‐02‐27

C5266091_X8_Ed.1 1/1 Letter of Authorization Shenzhen Funxim Innovation Technology Co., Ltd Company: Shenzhen Funxim Innovation Technology Co., Ltd Address: Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China. Product Name: wireless charger pad Model Number: IH-QI1102W, X8, X9, S8 FCC Identifier: 2AVJR-X8 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Xueshouzhen Date: 2/27/2020 Title: general manager Signature of applicant:

C5266091_X10_Ed.1 1/1 Shenzhen Funxim Innovation Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2/27/2020 Subject: Request for Confidentiality FCC ID: 2AVJR-X8 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Xueshouzhen 2/27/2020 Title: general manager

- Page 1 of 4 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China APPENDIX 1: EUT PHOTO Photo 1 (For model IH-QI1102W) Photo 2 - Page 2 of 4 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 3 Photo 4 - Page 3 of 4 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 5 Photo 6 - Page 4 of 4 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 7 ----END OF REPORT----

- Page 1 of 5 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China APPENDIX 1: EUT PHOTO Photo 1 (For model IH-QI1102W) Photo 2 - Page 2 of 5 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 3 Photo 4 - Page 3 of 5 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 5 Photo 6 - Page 4 of 5 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 7 Photo 8 - Page 5 of 5 - Report No.: MTi19120416-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 9 Photo 10 ----END OF REPORT---- Wireless Charging Ant

EXPOSURE REPORT FCC ID: 2AVJR-X8 Date of issue: Jan. 04, 2020 Report Number: MTi19120416-1E2 Sample Description: wireless charger pad Model(s): IH-QI1102W, X8, X9, S8 Applicant: Shenzhen Funxim Innovation Technology Co., Ltd Address: Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China. Date of Test: Dec. 17, 2019 - Jan. 04, 2020 Shenzhen Microtest Co., Ltd. http://www.mtitest.com Test Result Certification Applicant’s name: Shenzhen Funxim Innovation Technology Co., Ltd Address: Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China. Manufacture's name: Shenzhen Funxim Innovation Technology Co., Ltd Address: Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China. Product name: wireless charger pad Trademark: N/A Model name: IH-QI1102W, X8, X9, S8 Standard: FCC CFR 47 PART 1 , 1.1310 RF Exposure Procedures: KDB 680106 D01 RF Exposure Wireless Charging App v03 This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Tested by: Danny Xu Jan. 04, 2020 Reviewed by: Leo Su Jan. 04, 2020 Approved by: Tom Xue Jan. 04, 2020 1 General Information 1.1 Description of EUT Product name: wireless charger pad Brand name: N/A Model name: IH-QI1102W Series model: X8, X9, S8 Deference in serial model: All the model are the same circuit and RF module, except the model No.. Operation frequency: 115–205 kHz Operational mode: Wireless charging Modulation type: Load modulation Antenna type: Coil Antenna Power source: DC 9V from adapter AC 120V/60Hz Battery: N/A Adapter information: N/A 1.2 Ancillary equipment list Equipment Model S/N Manufacturer Adapter EQ-24BCN / Huizhou Dongyang Yienbi Electronics Co., Ltd. Mobile phone S9+ / SAMSUNG Apple Watch / / Apple 1.3 Measurement uncertainty Measurement Uncertainty for a Level of Confidence of 95 %, U=2xUc(y) Radiated emission(150kHz~30MHz) ± 2.5 dB Radiated emission(30MHz~1GHz) ± 4.2 dB Radiated emission (above 1GHz) ± 4.3 dB Temperature ±1 degree Humidity ± 5 % 2 Testing site Test Site Shenzhen Microtest Co., Ltd Test Site Location No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China FCC Registration No.: 448573 3 List of test equipment Equipment No. Equipment Name Manufacturer Model Serial No. Calibration date Due date MTI-E068 Broadband Field Meter Narda Safety Test Solutions GmbH NBM- 520 D-1699 2019/07/13 2020/07/12 MTI-E069 Probe E-Field Narda Safety Test Solutions EF0691 H-0571 2019/07/13 2020/07/12 4 Test Results 4.4 Maximum permissible exposure 4.4.1 Limit Frequency range(MHz) Electric field strength(V/m) Magnetic field strength(A/m) Power density(mW/cm2) Averaging time(minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 *100 6 3.0-30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 6 300-1500 f/300 6 1500-100000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *100 30 1.34-30 824/f 2.19/f *180/f 2 30 30-300 27.5 0.073 0.2 30 300-1500 f/1500 30 1500-100000 1 30 f = frequency in MHz * = Plane-wave equivalent power density 4.4.2 Test Procedures E and H-field measurements should be made with the center of the probe at a distance of 15 cm surrounding the device and 20 cm above the top surface of the primary/client pair. These measurements should be repeated for three different client battery levels, 1%, 50%, and 99%. Record the test results. KDB 680106 D01 RF Exposure Wireless Charging App v03: (1) Power transfer frequency is less than 1MHz. (2) Output power from each primary coil is less than or equal to 15 watts. (3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. (4) Client device is placed directly in contact with the transmitter. (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). (6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Note: The device is in compliance with KDB 680106 D01 RF Exposure Wireless Charging App v03 6 conditions. 4.4.3 Test Setup Right Side 15cm Field Probe Top Side Left Side Bottom Side Front Side Back Side 4.4.4 Test Result Maximum permissible Exposure Battery levels Test sides Test distance(cm) E –field(V/m) H–field(A/m) <1% Top 20 0.424 0.116 <1% Bottom 15 0.420 0.110 <1% Left 15 0.423 0.113 <1% Right 15 0.421 0.106 <1% Front 15 0.418 0.104 <1% Back 15 0.410 0.112 Limit 614 1.63 Margin Limit (%) 0.069% 7.12% Maximum permissible Exposure Battery levels Test sides Test distance(cm) E –field(V/m) H–field(A/m) <50% Top 20 0.422 0.119 <50% Bottom 15 0.409 0.115 <50% Left 15 0.411 0.113 <50% Right 15 0.414 0.108 <50% Front 15 0.413 0.110 <50% Back 15 0.419 0.107 Limit 614 1.63 Margin Limit (%) 0.069% 7.30% Maximum permissible Exposure Battery levels Test sides Test distance(cm) E –field(V/m) H–field(A/m) <99% Top 20 0.431 0.120 <99% Bottom 15 0.425 0.107 <99% Left 15 0.421 0.106 <99% Right 15 0.416 0.102 <99% Front 15 0.420 0.113 <99% Back 15 0.417 0.106 Limit 614 1.63 Margin Limit (%) 0.070% 7.36% 4.4.5 MPE Setup photo ----END OF REPORT----

This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Test Report FCC ID: 2AVJR-X8 Date of issue: Jan. 04, 2020 Report number: MTi19120416-1E1 Sample description: wireless charger pad Model(s): IH-QI1102W, X8, X9, S8 Applicant: Shenzhen Funxim Innovation Technology Co., Ltd Address: Room 510, Bozhi Center, No.62, 1st BaoTian Road, Baoan District, Shenzhen, China. Date of test: Dec. 17, 2019 – Jan. 04, 2020 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 25 - Report No.: MTi19120416-1E1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Table of Contents 1 GENERAL INFORMATION ................................................................................................................................. 4 1.1 FEATURE OF EQUIPMENT UNDER TEST (EUT) ................................................................................................................... 4 1.2 TEST MODE .............................................................................................................................................................. 4 1.3 EUT TEST SETUP ....................................................................................................................................................... 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 1.5 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 5 2 SUMMARY OF TEST RESULT ............................................................................................................................. 6 2.1 OPERATION CHANNEL LIST ........................................................................................................................................... 6 2.2 TEST CHANNEL .......................................................................................................................................................... 6 3 TEST FACILITIES AND ACCREDITATIONS ............................................................................................................ 7 3.1 TEST LABORATORY ..................................................................................................................................................... 7 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 3.3 MEASUREMENT UNCERTAINTY ...................................................................................................................................... 7 3.4 TEST SOFTWARE ........................................................................................................................................................ 7 4 LIST OF TEST EQUIPMENT ................................................................................................................................ 8 5 TEST RESULTS .................................................................................................................................................. 9 5.1 ANTENNA REQUIREMENT ............................................................................................................................................ 9 5.1.1 Standard requirement ................................................................................................................................. 9 5.1.2 EUT Antenna ............................................................................................................................................... 9 5.2 CONDUCTED EMISSION ............................................................................................................................................. 10 5.2.1 Limits ......................................................................................................................................................... 10 5.2.2 Test Procedures ......................................................................................................................................... 10 5.2.3 Test Setup .................................................................................................................................................. 10 5.2.4 Test Result ................................................................................................................................................. 10 5.3 RADIATED EMISSION ................................................................................................................................................. 15 5.3.1 Limits ......................................................................................................................................................... 15 5.3.2 Test Procedures ......................................................................................................................................... 16 5.3.3 Test Setup .................................................................................................................................................. 17 5.3.4 Test Result ................................................................................................................................................. 17 5.4 OCCUPIED BANDWIDTH ...........................................................................................................…

Text truncated - open the document above for the full version.

Model: IH-QI1102W Radiated emission Conducted emission