2AVLZ-PESDEYE-GRechargeable Soundwear Eye Mask

USER MANUALUSER MANUAL MODEL: PESDEYE-GMODEL: PESDEYE-G 13 2 IMPORTANT SAFETY INSTRUCTIONS DO NOT DESTROY 1. Read and follow all operating instructions prior to using this product. 2. Stop using this product immediately if it becomes damaged or is found to be defective. 3. Do not attempt to disassemble the battery unit if the battery unit is broken, cracked, or ruptured. If it is broken, avoid contact with skin and discard immediately. In the event of contact with skin, mouth, or eyes, flush immediately with cold water and consult a physician. 4. Discontinue use immediately if infrared heating elements become uncomfortably hot. 5. Keep out of reach of children. 6. Do not use this product if the battery unit, temperature controller or heating elements will be directly exposed to water or wet conditions. 7. This device contains a lithium-ion battery. The battery must be recycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal. PRODUCT SPECIFICATIONS Size:19.6” x 4.7” x 1.1” Weight:0.33 lb Charger Input:100-240V, 50/60Hz Output: DC 5V 1A Battery Type: Lithium-ion 350mAh 3.7V Battery Life:4-8 hours Battery Charge Time:Approximately 1 hour Material:100% polyester 23 USING THE EYE MASK Turn On/Off Power To turn on: Press and hold the Power Button until the blue Power Light comes on. To turn off: Press and hold the Power Button until the blue Power Light turns off. Turn On Sound Press the Music Button. The blue Music Indicator Light will turn on: • 1st press - Nature Sound #1 • 2nd press - Nature Sound #2 • 3rd press - Nature Sound #3 • 4th press - Bluetooth Mode (use to stream music or podcasts) NOTE: Wave is designed with soft speaker technology to help you relax. It is best used to play soft, soothing sounds. Pairing Bluetooth 1. Disconnect phone or other electronic device from other Bluetooth devices. 2. Turn on the eye mask’s sound and enter Bluetooth Mode. 3. Access Bluetooth pairing in phone or other device. 4. Select the Bluetooth device named "PESDEYE-G" and connect to it. Answering or Making Phone Calls There is no phone call setting built int o this device. Please make and answer calls directly from the smartphone paired to the device. Adjusting Volume • Press the ( - ) Volume Decrease Button to turn down the volume • Press the ( + ) Volume Increase Button to turn up the volume Low Power Warning When the eye mask is low on power, you will hear a reminder sound. Please charge the device with the included charger. While the device is charging, the Charging Light is red. When the battery is fully charged the Charging Light turns off. INTRODUCTION Thank you for purchasing the Wave Sound Therapy Eye Mask with Bluetooth Speakers from Pure Enrichment. This luxurious eye mask effectively blocks out light while providing soothing sounds to lull you to sleep. PRODUCT FEATURES We designed the Wave Sound Therapy Eye Mask with several features that make it a calming and comforting eye mask. These include: • Easy Touch Controls • Built-In Battery • Adjustable Fit • Removable Cover • Bluetooth Connectivity • 3 Nature Sounds: Rain, Stream, and Ocean CONTROL P ANEL DIAGRAM 45 1. Power Button 2. Charging Light 3. Volume Increase Button 4. Music Button 5. Music Indicator Light 6. Volume Decrease Button 7. Power Light 45 CARE & MAINTENANCE To prolong the life of your Wave eye mask, proper care and cleaning are essential. Follow these instructions to preserve the softness of the fabric and protect the electrical components. 1. Always unplug the eye mask from the electrical outlet, connecting cable, and battery before cleaning. 2. Remove the outer cover. 3. Spot clean with a damp clot h or hand wash in cold water with mild detergent. Do not place it in the washing machine. 4. Hang dry. WARRANTY The Wave Sound Therapy Eye Mask comes with an industry- leading 5 Year Warranty that begins on the date of purchase. The warranty applies to the sound therapy eye mask and necessary parts and labor relating thereto. The warranty does not apply to damage resulting from failure to follow the operating instructions, accidents, abuse, alterations, or disassembly by unauthorized individuals. PRODUCT REGISTRATION To ensure your full warranty and to receive product updates and streamlined customer support, remember to register your product at: www.pureenrichment.com/productregistration 67 FCC NOTICE Model: Wave Sound Therapy Eye Mask (PESDEYE-G) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The product is protected against unauthorized use. DO NOT modify it without the authorization of the manufacturer, or the user’s authority to operate could be voided. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful int erference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Bear Down Brands…

Text truncated - open the document above for the full version.

Bear Down Brands LLC. Agent Authorization Company: Bear Down Brands LLC. Address: 14505 Astronautics Lane Huntington Beach, CA 92647 Product Name: Rechargeable Soundwear Eye Mask Model Number(s ): PESDEYE-G Product Description: Rechargeable Soundwear Eye Mask We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2020/01/13 Name: Mat Weiss Title: Manager Company: Bear Down Brands LLC.

Bear Down Brands LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020/01/13 Subject; Request for Confidentiality FCC ID: 2AVLZ-PESDEYE-G To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Mat Weiss Title: Manager

External Photos

Size: 2.5*5.45 in with stich space Label location

Internal Photos Antenna

RF EXPOSURE EVALUATION METHOD FCC ID: 2AVLZ-PESDEYE-G SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. BT-EDR max possible output power (PK,conducted)：2±1dbm 0dBi logarithmic terms convert to numeric result is nearly 1 3dbm=2.00mW 2402MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]=2.00/5*√2.402 =0.62≤3.0 Modulation Frequency (MHz) Output Power (dBm) Max Antenna Gain (dBi) GFSK 2402 -0.91 0 GFSK 2441 -1.78 0 GFSK 2480 -2.83 0 Pi/4 DQPSK 2402 1.51 0 Pi/4 DQPSK 2441 0.63 0 Pi/4 DQPSK 2480 -0.47 0 8DPSK 2402 2.15 0 8DPSK 2441 1.25 0 8DPSK 2480 0.17 0 Threshold at which no SAR required is 10mw and ≤ 3.0 for 1-g SAR, Separation distance is 5mm. 2441MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 2.00/5*√2.441 =0.62≤3.0 Threshold at which no SAR required is 10mw and ≤ 3.0 for 1-g SAR, Separation distance is 5mm. 2480MHz [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]=2.00/5*√2.48=0.63≤3.0 Threshold at which no SAR required is 10mw and ≤ 3.0 for 1-g SAR, Separation distance is 5mm. Conclusion: No SAR is required.

Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E FCC Part 15C Test Report FCC ID: 2AVLZ-PESDEYE-G Product Name: Rechargeable Soundwear Eye Mask Trademark: N/A Model Name : PESDEYE-G Prepared For : Bear Down Brands LLC Address : 14505 Astronautics Lane Huntington Beach, CA 92647 Prepared By : Shenzhen BCTC Testing Co., Ltd. Address : BCTC Building & 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Test Date: Dec. 17, 2019 – Dec. 26, 2019 Date of Report : Dec. 26, 2019 Report No.: BCTC1912001526E Te s t Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-0 07 Ver.：A.0 Page 1 of 69 Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E TEST RESULT CERTIFICATION Applicant’s name ............. : Bear Down Brands LLC Address .............................. : 14505 Astronautics Lane Huntington Beach, CA 92647 Manufacture's Name ........ : Dongguan Taishin Electronic CO., Ltd Address .............................. : Building E, Dadi lndustrial Park, Chukeng, Dongkeng, Dongguan, China Product description Product name..................... : Rechargeable Soundwear Eye Mask Trademark ......................... : N/A Model and/or type reference PESDEYE-G Standards ......................... : FCC Part15.247 ANSI C63.10:2013 This device described above has been tested by BCTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of BCTC, this document may be altered or revised by BCTC, personal only, and shall be noted in the revision of the document. Prepared by(Engineer): Willem Wang Reviewer(Supervisor): Eric Yang Approved(Manager): Zero Zhou Te s t Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-0 07 Ver.：A.0 Page 2 of 69 Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E Table of Contents Test Report Declaration Page 1. TEST SUMMARY ...................................................... 5 2. TEST FACILITY ....................................................... 6 3. MEASUREMENT UNCERTAINTY........................................ 6 4. GENERAL INFORMATION .............................................. 7 4.1 GENERAL DESCRIPTION OF EUT ...................................... 7 4.2 Test Setup Configuration ................................................ 8 4.3 Support Equipment ..................................................... 8 4.4 Channel List ........................................................... 9 4.5 Test Mode ............................................................ 10 5. TEST FACILITY AND TEST INSTRUMENT USED ........................ 11 5.1 Test Facility ........................................................... 11 5.2 Test Instrument Used .................................................. 11 6. CONDUCTED EMISSIONS ............................................. 13 6.1 Block Diagram Of Test Setup ........................................... 13 6.2 Limit ................................................................. 13 6.3 Test procedure ........................................................ 13 6.4 Test Result ........................................................... 15 7. RADIATED EMISSIONS ............................................... 17 7.1 Block Diagram Of Test Setup ........................................... 17 7.2 Limit ................................................................. 18 7.3 Test procedure ........................................................ 18 7.4 Test Result ........................................................... 20 7.5 RADIATED BAND EMISSION MEASUREMENT AND RESTRICTED BANDS OF OPERATION ........................................................... 24 8. CONDUCTED EMISSION .............................................. 27 8.1 Block Diagram Of Test Setup ........................................... 27 8.2 Limit ................................................................. 27 8.3 Test procedure ........................................................ 27 8.4 Test Result ........................................................... 28 9. 20 DB BANDWIDTH .................................................. 37 9.1 Block Diagram Of Test Setup ........................................... 37 9.2 Limit ................................................................. 37 9.3 Test procedure ........................................................ 37 9.4 Test Result ........................................................... 38 10. MAXIMUM PEAK OUTPUT POWER .................................... 43 10.1 Block Diagram Of Test Setup .......................................... 43 10.2 Limit ................................................................ 43 10.3 Test procedure ....................................................... 43 10.4 Test Result .......................................................... 44 11. HOPPING CHANNEL SEPARATION .................................... 49 11.1 Block Diagram Of Test Setup .......................................... 49 Te s t Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-0 07 Ver.：A.0 Page 3 of 69 Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E 11.2 Limit ................................................................ 49 11.3 Test procedure ....................................................... 49 11.4 Test Result .......................................................... 50 12. NUMBER OF HOPPING FREQUENCY .................................. 55 12.1 Block Diagram Of Test Setup .......................................... 55 12.2 Limit ................................................................ 55 12.3 Test procedure ....................................................... 55 12.4 Test Result .......................................................... 56 1…

Text truncated - open the document above for the full version.

Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E 16. EUT TEST SETUP PHOTOGRAPHS Conducted Measurement Photos Te s t Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-0 07 Ver.：A.0 Page 68 of 69 Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC1912001526E Radiated Measurement Photos ※※※※※ END OF REPORT ※※※※※ Te s t Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-0 07 Ver.：A.0 Page 69 of 69