2AVMOANT-5-XMicrowave sensor

This function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice before switch-off. The sensor offers 3 levels of light: 100%-->dimmed light (natural light is insufficient) -->off; and 2 periods of selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area. With suffcient natural light, the light does not switch on when presence is detected. With insufficient natural light, the sensor switches on the light automatically when presence is detected. After hold-time, the light dims to stand-by level if the surrounding natural light is below the daylight threshold. Light switches off automatically after the stand-by period elapses. Corridor Function The ANT-5-4 is a motion sensor that dims lighting from high to low based on movement. This slim, low-profile sensor is designed for installation inside the bottom of a light fixture body. The sensors use microwave sensing technology that reacts to changes in movement within the coverage area. Once the sensor stops detecting movement and the time delay elapses lights will go from high to low mode and eventually to an OFF position if it is desired. Sensors must directly “see” motion of a person or moving object to detect them, so careful consideration must be given to sensor luminaire placement and lens selection. Avoid placing the sensor where obstructions may block the sensor’s line of sight. -1--2- INTRODUCTION SPECIFICATIONS Bi-level Microwave Sensor For High Bay Light ANT-5-4 Instruction Bi-level Microwave Sensor For High Bay Light ANT-5-4 Instruction RC-100 Every 30min Check Hold-time ends Power On Dim 100% On Off motion No motion When the natural light level exceeds setpoint off to light,the light will turn off even if when the space is occupied. 100% on when movement detected, and dims to 10% in long absence. 13 goes in cycle at night ... 4 08:10 The light automatically turns on at 10% when natural light is insuffcient (no motion). 5 17:40 Daylight Sensor Function Open the daylight sensor by push when remote control is in setting condition. The light dims to stand-by level after the hold-time. The light switches on at 100% when there is movement detected. 1 21:00 The light remains in dimming level at night. 3 21:40 2 21:10 Settings on this demonstration: Hold-time: 30min Setpoint on:50lux Stand-by Dim: 10% Stand-by period: +∞ Setpoint off:300lux (when the smart photocell sensor open, the stand-by time is only +∞) SENSOR COVERAGE Coverage Side View 0'6'12'30'12'6'30'20'20' 0 10' 20' 30' 40' ' 0'3'6'12' 30' 12'6'3'27' 30' 20' 20' 0' 3' 6' 3' 6' 12' 27' 30' 12' 27' 20' 20' 60 ft 30' 27' V1.2 41.3 12.5 7.5 7.3 43 G1/2 51 2-R1.6 55 23° ANT-5-4 ANT-5-4T （sensor） ANT-5-4B （connecting base） Cable length: 300mm WARNING NOTE: Warm up time is 15seconds. After the sensor connects input power first time, the light will keep on 15seconds, then go to dimming to work normally. NOTE: Factory Default Setting: 100% sensitivity, Hold on time: 5min, Daylight sensor is , Dimming level: 30%,Dimming time: 60minitues. NOTE: Any setting changed by remote control, the led light that sensor connect will on/off as confirm. Cable specifications: AWM 2464 /22AWG /80°C /300V 18.4 24.8 25 28.5 23.2 31.2 3- 2.39 44 18 9 G1/2 0-10V, max. 25mA sinking current 12V-24V DC, >50mA 5.8GHz±75MHz Detection radius 20%/50%/75%/100%(1-8m) Max 50ft.(15meters) IP65 -4°F ~ +140°F (-20°C ~ +60°C) 10s/1min/5min/10min/15min/20min/30min/60min 24H/10LUX/30LUX/50LUX Dim control output Power supply HF System Mounting height IP rating Temperature Time setting Light-control Transmission power <0.2mW WIRING DIAGRAMS 1 2 V D I M - L E D + L E D - D I M + L N L E D D r i v e r L N 0 - 1 0 V Black: 12-24Vdc Gray: DIM - Purple: DIM + FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIALZONE,HAISHU DISTRICT,NINGBO 315171,CHINA 053019 – 12 Authority to Act as Agent Date: March 10, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Intertek Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b),to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: Dec 30, 2020 By:_______________________________ Zhu Hui______ (Signature 1 )(Print name) Title:______manager__ _____________ On behalf of: ___Ningbo Sharkward Electronics Co.,Ltd_____ (Company Name) Telephone: +86-574-87795321 1 -Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIALZONE,HAISHU DISTRICT,NINGBO 315171,CHINA 053019 – 12 Request for Confidentiality Date: March 10, 2020 Subject: Confidentiality Request for: ______( FCC ID:2AVMOANT-5-X )_____ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality RequestedExhibit ☐Short Term☒PermanentBlock Diagrams ☐Short TermExternal Photos ☐Short Term☐Permanent * 2 Internal Photos ☐Short Term☒PermanentOperation Description/Theory of Operation ☐Short Term☐PermanentParts List & Placement/BOM ☐Short Term☐PermanentTune-Up Procedure ☐Short Term☒PermanentSchematics ☐Short TermTest Setup Photos ☐Short Term☐Permanent * 3 User’s Manual NINGBO SHARKWARD ELECTRONICS CO.,LTD.has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 3 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:________________________________Z hu Hui__________ (Signature/Title 4 )(Printname) 2 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 3 - Please refer tohttp://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdffor complete details. 4 -Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FCC ID: 2AVMOANT-5-X External Picture FCC ID: 2AVMOANT-5-X

Label Label Location

FCC ID: 2AVMOANT-5-X Internal Picture FCC ID: 2AVMOANT-5-X FCC ID: 2AVMOANT-5-X FCC ID: 2AVMOANT-5-X FCC ID: 2AVMOANT-5-X

NINGBO SHARKWARD ELECTRONICS CO.,LTD. SAR COMPLIANCE REPORT Report Type: FCC SAR assessment report Model: ANT-5-X REPORT NUMBER: 200100536SHA-002 ISSUE DATE: March 10, 2020 DOCUMENT CONTROL NUMBER: TTRFFCCSAR-01_V1 © 2018 Intertek Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCSAR-01_V1© 2018 Intertek Page 2 of 8 Report no.: 200100536SHA-002 Applicant: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA Manufacturer: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA Manufacturing site: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA FCC ID: 2AVMOANT-5-X SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: KDB447498 D01 General RF Exposure Guidance v06 FCC Part2.1091, FCC Part2.1093 FCC Part1.1307(b) PREPARED BY: REVIEWED BY: Project Engineer Stephanie Zhang Reviewer Wakeyou Wang Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 3 of 8 Revision History Report No. Version Description Issued Date 200100536SHA-002 Rev. 01 Initial issue of report March 10, 2020 Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 4 of 8 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: Microwave sensor Type/Model: ANT-5-X (X -For numbers, and representing different botton shell structure, but they are electrical identical) Description of EUT: EUT is a microwave sensor that dims lighting from high to low based on movement. It’s a transceiver with HF system 5.8GHz. Rating: Input: 12-24V Output: 0-10V 5.8GHZ Category of EUT: Class B EUT type: Table top Floor standing Software Version: / Hardware Version: / Sample received date: 2020.01.15 Date of test: 2020.01.16 ~ 2020.2.25 1.2 Technical Specification Frequency Range: 5725MHz – 5875MHz Support Standards: NA Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 5 of 8 1.3 Description of Test Facility Name: Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is recognized, certified, or accredited by these organizations: CNAS Accreditation Lab Registration No. CNAS L0139 FCC Accredited Lab Designation Number: CN1175 IC Registration Lab Registration code No.: 2042B-1 VCCI Registration Lab Registration No.: R-4243, G-845, C-4723, T-2252 NVLAP Accreditation Lab NVLAP LAB CODE: 200849-0 A2LA Accreditation Lab Certificate Number: 3309.02 Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 6 of 8 2 SAR Assessment Test result: Pass 2.1 SAR Test Exclusion Limit 100 MHz – 6 GHz and ≤ 50 mm Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 7 of 8 100 MHz – 6 GHz and > 50 mm < 100 MHz and < 200 mm Report No.: 200100536SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 8 of 8 2.2 Assessment Results The highest EIRP adjusted with tune-up tolerance is 73.10 dBuV/m, which is equivalent to -22.1dBm = 0.079mW < 6mW (Test Exclusion Thresholds of 5800MHz at 5mm). Therefore, the SAR requirement is deemed to be satisfied without test. ******************************************* END ************************************

NINGBO SHARKWARD ELECTRONICS CO.,LTD. RF TEST REPORT Report Type: FCC Part 15.249 & ISED RSS-210 RF report Model: ANT-5-X REPORT NUMBER: 200100536SHA-001 ISSUE DATE: March 10, 2020 DOCUMENT CONTROL NUMBER: TTRF15.249_V1 © 2018 Intertek Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.249_V1 © 2018 Intertek Page 2 of 25 Report no.: 200100536SHA-001 Applicant: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA Manufacturer: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA Manufacturing site: NINGBO SHARKWARD ELECTRONICS CO.,LTD. #88 GONGMAO ROAD NO.3,JISHIGANG INDUSTRIAL ZONE,HAISHU DISTRICT,NINGBO 315171,CHINA FCC ID: 2AVMOANT-5-X SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2018): Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices RSS-210 Issue 9 (August 2016): Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment RSS-Gen Issue 5 (April 2018): General Requirements for Compliance of Radio Apparatus PREPARED BY: REVIEWED BY: Project Engineer Stephanie Zhang Reviewer Wakeyou Wang Report No.: 200100536SHA-001 TEST REPORT TTRF15.249_V1 © 2018 Intertek Page 3 of 25 Content REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 6 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST ................................................................................................................... 8 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 8 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 8 2.5 TEST ENVIRONMENT CONDITION: ............................................................................................................................ 8 2.6 INSTRUMENT LIST ................................................................................................................................................ 9 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 10 3 RADIATED EMISSION ................................................................................................................................. 11 3.1 LIMIT .............................................................................................................................................................. 11 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 11 3.3 TEST CONFIGURATION ........................................................................................................................................ 13 3.4 TEST RESULTS OF RADIATED EMISSIONS ................................................................................................................. 15 4 POWER LINE CONDUCTED EMISSION ......................................................................................................... 19 4.1 LIMIT .............................................................................................................................................................. 19 4.2 TEST CONFIGURATION ........................................................................................................................................ 19 4.3 MEASUREMENT PROC…

Text truncated - open the document above for the full version.

FCC ID: 2AVMOANT-5-X Test Setup Radiated Emission 30M-1G FCC ID: 2AVMOANT-5-X >1G FCC ID: 2AVMOANT-5-X Conducted emission